015-02-06 V1.00.00 Note: This manual applies to iCarsoft 2nd generation serial products and CR Plus and is subject to change without prior written notice. In addition, all instructions and illustrations herein are mainly prepared based on iCarsoft 2nd generation serial products. Please kindly note that no further descriptions will be given for CR Plus as most major operation differences (excluding user interface) between iCarsoft 2nd generation serial products and CR Plus are clearly marked.
iCarsoft English User’s Manual Disclaimer To take full advantage of the unit, you should be familiar with the engine. All information, illustrations, and specifications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make change at any time without notice.
iCarsoft English User’s Manual Table of Contents 1. INTRODUCTION................................................................................................... 1 1.1 ICARSOFT 2ND GENERATION SERIAL PRODUCTS............................................ 1 1.2 CR PLUS........................................................................................................... 1 2. General Information...............................................................................................3 2.
iCarsoft English User’s Manual 1. INTRODUCTION 1.1 iCarsoft 2nd Generation Serial Products The iCarsoft 2nd generation Serial products cover the following models: MB II, FD II, VAG II, POR II, VOL II, OP II, LR II, TYT II, CP II, RT II, FT II, G-M II, NIS II and MMA II, which are especially designed for the DIY users and the servicemen of small service workshop.
iCarsoft English User’s Manual In addition to amazing & powerful diagnosing function, CR Plus also features some special functions such as Oil/ Service lamp reset, EPB and SAS etc. It can be upgraded via TF card: Download the upgrade package into the TF card and then insert the TF card into your tool to keep it updated with the latest software version.
iCarsoft English User’s Manual 2. General Information 2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed.
iCarsoft English User’s Manual 2.3 Location of the Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic code readers interface with the vehicle’s on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location.
iCarsoft English User’s Manual 3. Product Descriptions 3.1 Outline of iCarsoft Serial products / CR Plus Figure 2-1 1 OBD-16 Connector Connects the iCarsoft Serial products / CR Plus to the vehicle’s Data Link Connector (DLC) via the diagnostic cable. ▲/▼Button Move cursor up or down for selection. 2 ►/◄ Button Move cursor right or left for selection; Or turn page up or down when more than one page is displayed. 3 OK Button Confirms a selection (or action) from a menu list.
iCarsoft English User’s Manual previous screen. 5 Button To retrieve the DTCs in the database. 6 LCD Display Indicates test results. 7 USB Port To connect to PC to install the new software 8 TF card slot Insert the TF card into it to update your tool. 3.2 Specifications 1) Screen: 4.
iCarsoft English User’s Manual 4. Connections & Settings 4.1 Install TF card 1) Take out the TF card from package box. 2) Insert the TF card into the TF card slot perpendicularly. Make sure is fully inserted in the right place with the “micro” label facing upward. Note: You can hear a clicking sound if you insert the TF card in the right place. Press the card slightly, it will be ejected automatically. 4.2 Connections 1) Turn the ignition off. 2) Locate the vehicle’s DLC socket.
iCarsoft English User’s Manual 4.2 Settings Select [Settings] in the main menu and press [OK] to enter. Figure 3-2 1) Language This option enables you to set the user interface language. Note: Due to continuous software upgrade, language interface may differ from different software versions. 2) Unit of Measure This option allows you to set measurement unit. 3) Beeper It is used to set On/Off the buzzer. 4.3 Help This menu enables you to view device information and OBD introduction.
iCarsoft English User’s Manual Figure 3-3 1) DLC Location Position This option helps you to find the location of vehicle’s DLC. 2) DTC Library In Figure 3-3, select [DTC Library] and press [OK] to enter the following screen. Figure 3-4 Press [►]/[◄] to move the highlight bar to different position; press [▲]/[▼] to alter the value, and then press [OK] to retrieve the definitions of the DTC. 3) Abbreviation In Figure 3-3, select [Abbreviation] and press [OK] to enter the abbreviation word list.
iCarsoft English User’s Manual Figure 3-5 Press [►]/[◄] to turn to next or previous page; press [▲]/[▼] to select different items, and then press [OK] to view its full name and explanations. 4) Tool Information In Figure 3-3, select [Tool Information] and press [OK] to view the related information of iCarsoft Serial products / CR Plus.
iCarsoft English User’s Manual 5. Diagnose Select [Diagnose] in main menu screen and press [OK], the screen will display as follows: Figure 5-1 In Figure 5-1, press [OK] to enter system, a screen similar to Figure 5-2 will appear: Figure 5-2 (For iCarsoft Serial products) Note: For different models, this page may vary from different vehicle makes.
iCarsoft English User’s Manual Figure 5-2 (For CR Plus) 5.1 OBDII/EOBD Diagnosing This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related. In Figure 5-2 (For iCarsoft Serial products), press [OK] and the screen will enter Fig. 5-3.
iCarsoft English User’s Manual Figure 5-4 It mainly includes the following functions: 1. Read Codes -- This option is used to identify which section of the emission control system has malfunctioned. 2. Erase Codes -- It is used to clear the diagnostic trouble codes. 3. I/M Readiness -- I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. 4. Read Data Stream 5.
iCarsoft English User’s Manual Number (VIN), the Calibration Verification Number (CVN), and other information of the test vehicle. 5.2 System Diagnosing (For iCarsoft Serial products) This function is specially designed to diagnose all electronic control systems of single vehicle model. Note: Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your iCarsoft Serial products.
iCarsoft English User’s Manual Select Vehicle Model (Note: For different vehicles, vehicle make selection may differ. Generally we can choose a vehicle via make year. But for BENZ, we need to choose it via chassis.) Select test system Automatic (Note: This mode allows your tool to scan the vehicle test system automatically.) Manual Select (Note: In this case, you need to choose the desired system manually. Just follow the on-screen instructions to proceed.
iCarsoft English User’s Manual SRS (Supplemental Restraint System) Note: Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your CR Plus. Refer to the flowchart illustrated as below to diagnose a vehicle: Note: For vehicles manufactured by different vendors, it is possible that it has different diagnostic menus. For details, please follow the instructions on the screen to proceed.
iCarsoft English User’s Manual 6. Register & Update Hardware Requirement: 1. A computer that can access to the Internet. 2. A TF card reader/writer and a TF card that need to be updated. Follow the steps described as below to proceed registration and update: 1. Install the iCarsoft Serial products update tool and launch it. 2. You will be prompted to type in the Serial Number (located on the back of the tool) Figure 5-1 3. After the Serial Number is entered, click [Update] to enter Figure 5-2.
iCarsoft English User’s Manual (If you need the Register Code, proceed to the steps 4-7) (If you have the Register Code, proceed to step 8 directly) 4. The Register Code can be found by connecting the supplied USB cord to the iCarsoft Serial products / CR Plus and inserting into the computer. 5. When the tool has powered up, highlight “Help” icon and press [OK]. 6. Select Tool Information, press [OK]. Figure 5-3 7. This is the Register Code for inputting in step 3.
iCarsoft English User’s Manual 9. Reopen the update tool and select the update or click “Select All” and click “Download”. Figure 7 10. Once all steps are complete, reinsert the TF card into the tool and power the tool via USB in computer or via OBD2 port in vehicle. The tool will prompt you to upgrade, click “OK” to start updating and a progress bar will appear. It may take several minutes to finish update if your upgrade package file is too large, please wait. Figure 8 11.
iCarsoft English User’s Manual 7. FAQ Here we list some frequently asked questions and answers relating to iCarsoft Serial products / CR Plus. Question: System halts when reading data stream. What is the reason? Answer: It may be caused by a slackened connector. Please turn off the iCarsoft Serial products / CR Plus, firmly connect the connector, and switch on it again. Question: Screen of main unit flashes at engine ignition start.
21
