CR MAX BT User Manual PROFESSIONAL . FAST . SMART .
Trademarks iCarsoft, CR MAX BT is trademarks of iCarsoft Technology Inc, registered in the United States and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of iCarsoft.
safety messages are introduced by a signal word indicating the hazard level. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders. Safety Instructions The safety messages herein cover situations iCarsoft is aware of.
CONTENTS 1 Using this Manual.............................................................................................................. 1 1.1 Conventions ............................................................................................................ 1 2 General Introduction ......................................................................................................... 1 2.1 CR MAX BT Display Tablet.....................................................................................
.2 Play Back ...............................................................................................................35 6.3 User Manual ...........................................................................................................37 6.4 Training ..................................................................................................................37 6.5 Report.....................................................................................................................
1 Using this Manual This manual contains device usage instructions. Some illustrations shown in this manual may contain modules and optional equipment that are not included in your system. 1.1 Conventions The following conventions are used. 1.1.1 Illustrations Illustrations used in this manual are samples, the actual testing screen may vary for each vehicle being tested. Observe the menu titles and on-screen instructions to make correct option selection. 1.1.
This manual describes the construction and operation of the device and how it works to deliver diagnostic solutions. 2.1 CR MAX BT Display Tablet 2.1.1 Functional Description Figure 2-1 Display Tablet Front View 1. 7.0” LCD Capacitive Touchscreen. Figure 2-2 CR MAX BT Display Tablet Back View 2. 3. Collapsible Stand – extends from the back to allow hands-free viewing of the Display Tablet. Heat Sink or Speaker.
Figure 2-3 CR MAX BT Display Tablet Top View 4. 5. 6. Mini USB Port. USB Port –For connection of adapters, computers or VCI, etc. Lock/Power Button – long press button to turn tablet off and on. Quick press button to lock screen. 2.1.
Connectivity Body Color Audio Input/ Output Black Input: N/A Output: Buzzer & Speaker Power and Battery Mini USB 2.0 USB 2.0 Wi-Fi (2.4GHz) Bluetooth OBDII OBD DLC Voltage Range:9-18V 3.7V/5000mAh lithium-polymer battery Charges via 5V DC power supply Tested Battery Life Around 5 hours of continuous use Battery Charging Input 5V / 2A Power Consumption 500mA (LCD on with default brightness, Wi-Fi on) @3.7 V Operating Temp. 0 to 40°C (32 to 104°F) Storage Temp.
Figure 2-4 VCI view 1. Vehicle data connector (16-pin)-connects VCI directly to the vehicle's 16-pin diagnostic interface (DLC). 2. Mini USB Port - The CR MAX BT can be connected to the VCI through a USB cable. 3. Power indicator: red - When the VCI is connected to a power source, connected to a vehicle, or bound to a device, this indicator light is always bright red. 4.
Communication BT5.0 dual mode Wireless frequency 2.4 GHz Input voltage range 9V DC -- 18V DC Power supply current 100mA@12 V Operating temp. 0°C to 50°C(32°F to 122°F) Storage temp. -20°C to 70°C(-4°F to 158°F) Dimensions (L * W * H) 94 mm (3.7’’) * 56mm (2.2’’) * 28 mm (1.1’’) Weight ≈69g (0.152 lb.) 2.2.4 VCI Device binding VCI binds to tablet devices via Bluetooth or USB cable, generally the USB cable is faster. For the first binding, you can do as follows: 1.
Figure 2-6 VCI Device binding screen 2 3. After Bluetooth is connected, wait for the device to be searched, and tap the tablet with the same serial number as the VCI device to bind. Figure 2-7 VCI Device binding screen 3 4. After the binding is successful, the page will display a successful signal and display the serial number of the VCI device.
Figure 2-8 VCI Device binding screen 4 5. If you need to unbind, tap the unbind button in the lower right corner, and the device will be unbound, and you can re-bind with other VCI devices. 6. If the binding is successful, the VCI binding option on the setting page will display the serial number of the bound VCI device. 7.
connected to the data link connector (DLC) of the vehicle through the VCI Extended Cable, Transfer vehicle data to CR MAX BT tablet. Figure 2-12 VCI adapter 2.3.2 Other Accessories Mini USB Cable Connects the Display Tablet to the PC or DC external power adapter. USB External Power Adapter Together with the mini USB cable, connects the Display Tablet to the external DC power port for power supply. VCI Adapter Holder VCI Extended Cable Connect the vehicle and VCI device.
User Manual Tool operations instructions. Quick Guide Device connection and product unpacking list, product description, etc. 3 Getting Started Ensure the tablet is sufficiently charged or is connected to the external power supply (see Power Sources on section 2.1.2). NOTE The images and illustrations depicted in this manual may differ from the actual ones. 3.1 Powering Up Press the Lock/Power button on the top right side of the tablet to power the unit on.
1. 2. 3. Figure 3-1 Sample CR MAX BT Job Menu Application Buttons Navigation Buttons Status Icons NOTE The tablet screen is locked by default upon startup. It is recommended to lock the screen when not in use to protect the information in the system and conserve the power. Almost all operations on the tablet are controlled through the touchscreen.
Service Accesses special functions menu. See Service Operations on chapter 5. User Data Accesses the organization system for saved data files. See User Data Operations on chapter 6. Upgrade Checks for the latest update available for the CR MAX BT system, and performs updates. See Upgrade Operations on chapter 7. Shop Information Accesses the workshop information service program, including customer information records and test vehicle history records. See Shop Manager Operations on chapter 8.
3.1.2 Locator and Navigation Buttons Operations of the Navigation buttons at the bottom of the screen are described in the table below: Table 3-2 Locator and Navigation Buttons Button 3.2 Name Description Locator Indicates the location of the screen. Swipe the screen left or right to view the previous or next screen. Back Returns to the previous screen. Android Home Returns to Android System’s Home screen. Recent Apps Displays a list of applications that are currently in use.
4.1 Getting Started The Diagnostics operations require connecting the CR MAX BT to the test vehicle’s DLC using the main cable. 4.1.1 Vehicle Menu Layout When the tablet is properly connected to the vehicle, the platform is ready to start vehicle diagnosis. Tap on the Diagnostics application button on the CR MAX BT Job Menu, the Vehicle Menu then displays. Figure 4-1 Sample Vehicle Menu 1. 2.
History Displays stored test vehicle history records. USA Displays the USA vehicle menu. Europe Displays the European vehicle menu. Asia Displays the Asian vehicle menu. Search Searches for a specific vehicle make. Manufacturer Buttons The vehicle manufacturer buttons display the vehicle brands currently compatible with the tool. After establishing communication with the vehicle. Tap the desired manufacturer button to start a diagnostic session. 4.2 1. 2.
3. Figure 4-2 Sample VIN Identification Screen Once the test vehicle is successfully identified, the screen will show the Vehicle information: include VIN, model code, brand etc., then tap OK to enter the diagnosis. Figure 4-3 Sample Vehicle information Screen Manual VIN Input For some vehicles that not supporting the Auto VIN Scan function, the CR MAX BT diagnostic system allows you to enter the vehicle VIN manually. To perform Manual VIN Input 1.
2. 3. Select vehicle brand. If some vehicles do not support automatic VIN code recognition, you need to enter the VIN code manually. Tap the input box and enter the correct VIN. Figure 4-4 Sample VIN input Screen 4. 5. 4.2.2 Tap OK. The vehicle will be identified and the Vehicle Diagnostics screen will display. Tap Cancel to exit Manual Input.
Figure 4-5 Sample Diagnosis mode Screen The diagnostic screens typically include four sections. 1. Status Information Bar 2. Main Section Status Information Bar The Status Information Bar at the top of the Main Section displays the following items: 1) Back button – Returns to the CR MAX BT Job Menu. 2) Menu Title – displays the menu heading of the Main Section. 3) Voltage Icon – displays the vehicle’s voltage status.
This type of messages displays a warning that a selected action may result in an irreversible change or loss of data. The typical example of this is the “Erase Codes” message. Error Messages Error messages display when a system or procedural error has occurred. Examples of possible errors include a disconnection or communication interruption. 4.3.3 Making Selections The Diagnostics application is a menu driven program that presents a series of choices.
Right side – Show vehicle control unit status. Fault | (2) ： Indicates that the fault code is detected; 2 represents the number of faults detected. Pass ： Indicates that the vehicle is equipped with this system and has no fault code. Fitted ： Indicates that the vehicle is equipped with this system. Not Fitted ： Indicates that it is detected that the vehicle is not equipped with this system. Unknown ： Indicates that it is detected that it is unknown whether the vehicle is equipped with this system.
the program will guide you to the diagnostic function menu after selections are made. Figure 4-7 Sample Diagnostic Operation Screen The Function Menu options vary slightly for different vehicles. The function menu may include: 1. Module Information – Read full electronic system module information, such as VIN, part number, version, supplier, production date of ECU. 2. Read fault code – Read full electronic system module fault code, show state and description of fault code. 3.
including unit type, version numbers and other specifications. Also you can save these data by press save button. The sample Module Information screen displays as below: Read Fault Codes This function retrieves and displays the DTCs from the vehicle’s control system. The Read Codes screen varies for each vehicle being tested. On some vehicles, freeze frame data can also be retrieved for viewing.
1. Figure 4-8 Sample View Data Screen Main Section Name Column – displays the parameter names. a) Check Box – tap the check box on the left side of the parameter name to make item selection. Tap the check box again to de-select the item. b) Drop-down Button – tap the drop-down button on the right side of the parameter name to open a sub menu that provides various choices for data display mode. Value Column – displays the values of the parameter items.
Reading of status parameters, such as a switch reading, which are mostly in word form, such as ON, OFF, ACTIVE, and ABORT, can only be displayed in Text Mode. Whereas reading of value parameters, such as a sensor reading, can be displayed in text mode and other graph modes. 3) 2. Waveform Graph Mode – displays the parameters in waveform graphs. When this mode is applied, you can use two fingers to zoom in or out. 4) Digital Gauge Mode – displays the parameters in form of a digital gauge graph.
Window regulator front / rear left / right: down / up Through the window regulator action test item, you can control the whole vehicle window up and down to test whether the window up and down works normally. Windshield wiper motor (V) stage 1 / 2 Through the action test item of windshield wiper motor, the wiper can be controlled to work at 1 / 2 gear to test whether the wiper motor works normally 4.
NOTE Tapping ○ i button beside the function name to display additional function information. Select a function option to continue. Read Codes Erase Codes I/M Readiness Live Data Freeze Frame Vehicle Information O2 Monitor Test On-Board Monitor Evap System(mode$8) NOTE Some functions are supported only on certain vehicle manufacturers. 4.6.
erased. This Drive Cycle – displays the status of monitors since the beginning of the current drive cycle. Live Data This function displays the real time PID data from ECU. Displayed data includes analog inputs and outputs, digital inputs and outputs, and system status information broadcast on the vehicle data stream. Live data can be displayed in various modes, see View Data on section 4.5 for detailed information. Freeze Frame In most cases the stored frame is the last DTC that occurred.
diagnostic session step-by-step. From the Vehicle Menu screen, tap the Back button on the top toolbar; or tap the Back button on the navigation bar at the bottom of the screen. 3. Or tap the Home button on the diagnostics toolbar to exit the application directly and return to the CR MAX BT Job Menu.
Figure 5-1 Sample Service Function List After entering each special function, the screen will display the Vehicle Manufacturer, you need to make a step-by-step selection according to your test vehicle. 5.1 ABS Bleeding (BLD) Service When the ABS contains air, or the ABS computer / ABS pump / brake master cylinder / brake cylinder/ brake fluid is replaced, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. 5.
and effectively. The applications include deactivating and activating the brake control system, assisting with brake fluid control, opening and closing brake pads, and setting brakes after disc or pad replacement. Electronic Parking Brake (EPB) system maintenance, deactivates and reactivates the EPB system for replacement and initialization. 5.
each vehicle being tested. Observe the menu titles and on-screen instructions to make correct option selections. 3) Before starting the procedure, make sure the vehicle has an ESC button. Look for the button on dash. Steering Column Calibration If the steering column or instrument cluster is replaced or the instrument cluster software is updated, a body system steering column calibration is required. 5.
The ECM monitors driving style and selects a suitable time to employ regeneration. Cars driven primarily at idling speed and low load will attempt to regenerate earlier than cars driven with higher loads and at higher speed. For regeneration to occur, a prolonged high exhaust temperature must be obtained. In the event that the vehicle has been driven in such a way that regeneration is not possible, a diagnostic trouble code will be registered, DPF light and “Check Engine” indicator will display.
inputting TPMS sensor replacement IDs and testing sensors. Select tire pressure sensor replacement (Front right wheel sensor) as an example. 1) NOTE This function will require the sensor ID be inputted on the screen. 2) The sensor IDs can be read directly from the sensor or by using a sensor activation tool that can read the ID. 3) Once the IDs have been entered, the vehicle may have to be driven at a certain speed for a certain time to complete procedure. Follow the instructions displays.
and matching functions need to be performed to make the air filter work normally. 5.15 Fuel Pump After the fuel pump is disassembled, repaired or replaced, it may cause the fuel pump to be unable to continuously provide fuel to the fuel injection nozzle. At this time, the function needs to be executed to activate the replaced fuel pump so that the car can start to inject fuel normally and make the engine achieve the ideal Running status. 5.
Different models will have different menu modes. This manual is for reference. Everything in kind shall prevail. If there is any increase or decrease in the function of the product, the actual product shall prevail. 6 User Data The User Data application is used to store and view saved files. Contains images, play back, user manual, Training, Report, DLC Location. Details are explained in the following sections. 6.1 Image Files The Image section contains all captured screenshot images.
Figure 6-2 Sample Play Back Screen 2 3. Select the check box in the lower right corner of each list, tap the button in the upper right corner to execute PDF output function or delete. Figure 6-3 Sample Play Back Screen 3 Perform PDF output function： 1） Select one or more data lists and tap the button to enter the interface. In this interface, you can still move up, down, and delete.
corner, and an interface for outputting the report to PDF appears. Fill in the file name, vehicle, customer, and operator, and press the save button. 3） After the save is complete, the screen will show a message indicating that the save is successful, and inform the user of the save path of the report. Return to the previous menu, you can view the converted PDF report in "Report". Figure 6-4 Sample Play Back Screen 6 6.
The Update application allows you to download the latest released software. The updates can improve the CR MAX BT applications’ capabilities, typically by adding new tests, new models, or enhanced applications. The tablet automatically searches for available updates for the CR MAX BT software when it is connected to the internet. Any updates that are found can be downloaded and installed on the device. This section describes installing an update to the CR MAX BT System.
b) Tap Pause to suspend the software update. c) Tap Continue to resume updating the software. To update the software and database 1. Make sure the Display Tablet is connected to a power source with stable access to the internet. 2. Tap the Upgrade application button from the CR MAX BT Job Menu; or tap the update notification message when received; or tap the Upgrade icon on Vehicle Menu in Diagnostics application. The Update application screen displays. 3.
8.1 Modify edit and save Tap this button to save the modified customer information and vehicle information. Add Customer Notes Tap this button to open a note form. New customer notes can be added. Workshop Info Use the Workshop Information form to edit, input and save the detailed workshop information, such as shop name, address, phone number and other remarks, which when printing vehicle diagnostic reports and other associated test file, will display as the header of the printed documents.
Figure 8-1 Sample Customer Info Sheet 1 3. Tap on the input field that needs to be altered or supplemented, and enter updated information. 4. Tap the Modify edit and save button on the top toolbar to save the updated information, or tap the Back button on the top toolbar to exit without saving. To delete a customer account 1. Select Customer Info in the Shop Info application. 2. Select a customer account by tapping the corresponding name card. A Customer Information sheet displays. 3.
8.3 Vehicle History This function stores test vehicle history records, including vehicle information and the retrieved DTCs from previous diagnostic sessions. All information is displayed in summarized details. Tap on a record to resume a diagnostic session on a “stored vehicle”. Figure 8-2 Sample Vehicle History Screen To activate a test session for the recorded vehicle 1. Select Vehicle History in the Shop Info application. 2. Or, tap the vehicle record thumbnail to view record. 3.
System Settings Click To Restore Factory Settings This section describes the operation procedures for the settings. 9.1 VCI Binding The VCI binding option provides an entry for binding the VCI device and the tablet, and the user can perform VCI binding or unbinding operations here. For details, refer to section 2.2.4. 9.2 Unit This option allows you to change the measurement unit for the diagnostic system. Select the required measurement unit, Metric or Imperial.
Access the Android background system setting screen to adjust operating system settings including wireless and network settings, sound and display and system security settings. Android device information is also displayed. 9.10 Restore Factory Settings This option allows you to return to factory settings. This operation will initialize all data in the application settings, including unit, brightness, data switch, screen sleep and vehicle logo sorting.
provide information feedback. 1. Select the check box behind the log, you can select multiple logs at the same time, tap the delete button in the upper right corner to delete. 2. Select the check box behind the log, you can select multiple logs at the same time, tap 3. the feedback button in the upper right corner. The interface for information feedback will appear. Enter the title, description, vehicle information, etc. in the input box, "*" is required. Then tap the Upload button to submit feedback.
15 About The About screen lists the CR MAX BT’s version, hardware, and serial number, storage and etc.. 16 Maintenance and Service 16.1 Maintenance Instructions The following shows how to maintain your devices, together with precautions to take. Use a soft cloth and alcohol or a mild window cleaner to clean the touch screen on the tablet. Do not use any abrasive cleansers, detergent, or automotive chemicals to the tablet.
Make sure the tablet is connected to a power source or the battery is charged. D. When you are unable to charge the tablet: Your charger maybe out of order. Contact your nearest dealer. You may be attempting to use the device in an overly hot/cold temperature. Try changing the charging environment. Your device may have not been connected to the charger properly. Check the connector. NOTE If your problems persist, please contact iCarsoft’s technical support personnel or your local selling agent. 16.
This section introduces information for technical support, repair service, and application for replacement or optional parts. 16.4.1 Technical Support If you have any question or problem on the operation of the product, please contact us (see the following contact info) or your local distributor. ICARSOFT USA HQ Website: www.icarsoft.us www.icarsoft.com Email: support@icarsoft.com 16.4.
WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device is declared to be in compliance with the European RoHS Directive 2011/65/EU&2015/863/EU. CE COMPLIANCE This product is declared to conform to the essential requirements of the following Directives and carries the CE mark accordingly: EMC Directive RED Directive Low Voltage Directive 18 Warranty Limited One Year Warranty iCarsoft Technology Inc.
iCarsoft Technology Inc. www.icarsoft.us www.icarsoft.
