User's Manual

Smart Health Case
User Manual
5折页说明书 14.7X40cm 128g铜版纸
A
B
APP operation instructions
Step 1
Scan QR code to download and install APP:
Mobile phone system requirements：
Android 5.1 and above iOS 11.0 and above
Structural illustration
Main
Charge
1、right finger electrode
2、right finger auxiliary electrode
3、left finger electrode
4、PPG sensor window
5、LED indicator
6、power button
7、the host charging contact point
8、charger indicator
9、charger charging contact point
10、charging cable
11、USB charging plug
Welcome
This product uses advanced low-power Bluetooth technology and
all-in-one biosensor to achieve simple operation, measurement and
evaluation of ECG waveform, PPG waveform, heart rate, blood oxygen,
blood pressure trend, HRV and other physiological parameters anytime
and anywhere.
1. BLE4.2 technology support for IOS and Android operating systems
2. single measurement time of 1 minute, the number of measurements
can be more than 120 times
3.All-in-one sensor, reduce measurement equipment, reduce measure-
ment complexity and user cost
4.Small size, carry with the phone, easy to measure at any time
5.Measurable parameters include ECG waveform, PPG waveform, heart
rate, blood oxygen, blood pressure trend, HRV, etc
6.Personalized health analysis report
7. Cloud platform stores personal security data
Product Features
This User Manual describes in detail the use, functions, and usage of this
product (Smart Health Case Mode：ICX-SD-001). Before using this
product, please read and understand the contents of this manual to
ensure that the product can be used correctly.
All illustrations provided in this manual are for reference only and the
illustrations may not exactly match your product.
This User Manual contains proprietary material protected by copyright
law. All rights reserved. No part of this User Manual may be
photocopied, copied or translated into another language without the
written consent of the manufacturer.
The contents contained in this User Manual can be changed without
notice.
Summary
Power on
After long press of the button switch for about 0.5S, the green light
flashes to indicate that it has been turned on, and the green light is
flashed every 10 seconds when the power on status.
Automatic Power off
The red lights flashes 5 times when the power is turned off，The specific
logic is as follows
1、After the device is not connected to the APP, it will be turned off after
1 minute.
2、The APP is connected to the device after power-on. It is turned off
after 4 minutes without operation (3 minutes for keeping the
connection state, 1 minute for the scanable state).
Manual Power off
Press and hold the power button for more than 3S, the red-light flashes,
release the button, and the device is turned off.
Charging
The charger is connected to the host, and the USB port is plugged into
an adapter with an output voltage of 5V. If the voltage is not matched,
the device will be damaged.
The charger indicator status is as follows：
1 Charging: red light flashing 2 fully charged :red light is always on
Note: Do not use the device while charging
Click the measurement icon to start the measurement (the measure-
ment site is recommended for the fingertips of both hands)：
Step 4
Note: You need to keep your body still and calm
during measurement. The hands need to have
support. Do not leave the host electrode after
the measurement starts. Otherwise, the
measurement will fail. It is recommended to
clean your hands before measuring to make the
fingertips clean and moist. The required
measurement posture is shown below：
Step 5 Measurement completed
Charging input
Battery specification
Continuous test time
Shutdown standby time
Operating temperature
Storage temperature
Charging time
Waterproof
Determine whether there is no power or
low power state, try to power on after
charging
1、Please confirm that the device has
been automatically power off
2、Re-search for devices and connect
1、Determine whether to use in an
environment with more WiFi Bluetooth
devices. Please use it in a relatively
clean environment.
2、Reconnect after disconnecting the
device or restart the app after trying to
close the app
5V/50MA
3.7V/45mAh
120 Times
>180 day
0℃-50℃
-20℃-70℃
about 1 hour
IPX65
APP can't find device
Can not be turned on
Test Waveform delay or
APP tips for low Bluetooth speed
APP Tips Bluetooth disconnect
Please ensure that mobile data is unblocked
APP Tips measurement failed
APP Tips unable to connect
to the server
Electrical parameter
indicator status
Troubleshooting Method
Power on
Bluetooth connection
Normal operation
Bluetooth disconnect
Low power
Power off
Green light flashes 5 times
Green light flashes 3 times
Green light 10S flashes once
Red light flashes 3 times
Red light 10S flashes once
Red light flashes 5 times
from the following three aspects:
1、Whether the bluetooth of the mobile phone is
turned on (Mobile phone system settings)
2、Whether the device is turned on (the green light
flashes every 10S after starting up)
3、Restart the app or device
1、Keep your arms and body still when
measuring, ensuring correct
measurement posture
2、Wash your hands before measuring so
that your fingers are clean and moist
3、Click Cancel to restart measurement
Safety warnings and recommendations
After-sales and warranty terms
Manufacturer information
Official WeChat
Manufacturer:Shenzhen iCarbonX Living
Healthcare Management Co., Ltd.
address:311,3F,2B, Shahe Industrial Zone，No.
4018，Qiaoxiang Road，Nanshan District.Shen-
zhen
Website:www.icarbonx.com/
Warranty policy: Warranty or return according to the corresponding
national terms
Customer Service Phone: [phone]
1、Please read the safety instructions carefully and keep them for
future use.
2、Please keep this product away from fire, high temperature and
high-pressure environment.
3、Do not disassemble the host without permission. It is not allowed
to modify the product in any way.
4、Do not use chemical reagents to clean. Chemical reagents may
corrode the body surface.
5、Do not subject the surface of the body to gravity shock to avoid
damage to the machine.
6、charging requires the use of standard 5V adapter, otherwise
vulnerable to damage.
7、Do not use this device while charging.
8、When disposing of this product, please do not disassemble or
discard it. Please follow the relevant regulations in your area.
Maintenance and cleaning
The surface of the main unit can be wiped clean with a soft towel. Do
not use chemical cleaners.
Do not use for a long time, it is recommended to charge once every 3
months.
Store the main unit and charger in a cool dry place.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Register or log in to account settings
for personal information settings and
blood pressure calibration
Step 2
Step 3
Click the Bluetooth icon in the upper
right corner of the APP main interface
to scan the connected device：
Operating instructions
Use the host as shown below