Intercom: Monitor IC REALTIME SECURITY SOLUTIONS IHD-7310: Indoor Monitor Instruction Manual
IC REALTIME SECURITY SOLUTIONS IH-7310 Intercom Monitor Instruction Manual IC Realtime 3050 N Andrews Ave Ext Pompano Beach, FL 33064 Phone 954.772.5327 • Fax 866.860.
Table of Contents 1. Features and Specifications ....................................................................... 1 a. Overview .......................................................................................... 1 b. Features ............................................................................................ 1 c. Specifications ................................................................................... 2 d. Dimensions ...........................................................
I C R E A L T I M E S E C U R I T Y 1 Chapter S O L U T I O N S Features and Specifications This section outlines the primary features of the ICRealtime IH-7310 Intercom Monitor. It also outlines basic Architectural and Engineering specifications. 1.a Overview T his IC Realtime series product is design to work together with our other Intercom solution devices. The monitor incorporates a fully touch enabled screen for easy operation.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S Compression Format H.264 video and G.711 audio enables high quality video streaming while maintaining the lowest file sizes possible for smoother monitoring Local Operation Full system control is available at the monitor itself. No need to access over the network as well configurations can be made at the unit itself. 1.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S 1.
I C R E A L T I M E S E C U R I T Y 2 Chapter S O L U T I O N S Monitor Installation This section outlines the proper way to mount and install an IH-7310 series intercom monitor. The suitable method of installing the monitor is limited to Wall installations only. Note that hardware including screws and anchors are included for the camera installation. 2.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S 2.b Step by Step Guide Note: Reference the labeled table below for screw type Step 1: Install Wall Bracket to Gang Box (86 Box) Begin by using screw 'a' to fasten the wall bracket to your gang box (86 box). Assure a snug fit from the back plate to the wall and Gang Box. Step 2: Fasten to Wall Use screw 'b' to fasten to the actual wall. If you need, use anchors ('c') to fasten the screws better to the wall.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S 2.c Connections No. 1 Port Name Alarm Port Description Tie in alarm triggers to this port. See picture below for connections 2 Test Port For debugging only 3 Network Port RJ45 port to connect to your network 4 Power Terminal To power the unit. 12VDC only! 5 Analog/Handset Port Used for analog systems only.
I C R E A L T I M E S E C U R I T Y 3 Chapter S O L U T I O N S Local Screen Operation This section outlines how to assign an IP address to the monitor and to navigate through the touch controlled screen 3.a Main Interface Note: This device does not have a Web Interface and all configuration can be done at the monitor itself. This section will briefly go over the main interface and action buttons.
I C R E A L T I M E No. S E C U R I T Y S O L U T I O N S Name Description 1 Power Indicator Illuminates when unit is receiving proper power 2 Info Indicator Illuminates when unit has a new message or new information that has not been looked at 3 S.O.S Attempts to call the management center where all Intercom devices are managed.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S 3.c Pairing with Outdoor IP Camera Note: This section mainly references how to sync our Intercom outdoor IP cameras such as the IHC-6260 with a indoor monitor to complete a intercom setup. Note that this will reference your indoor monitor setup. Be sure the monitor is online and ready to be used on the network. Please reference our other guides for a complete setup. http://www.icrealtime.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S You should now see the added indoor monitor information on the table. You will now need to access the indoor monitor to add the IP address of this camera so to complete the pairing.
I C R E A L T I M E S E C U R I T Y S O L U T I O N S Navigate on the IH-7310 to 'Settings' 'Project Settings' 'Network'. Here you will input the IP address of the outdoor camera (IHC-6260). Tap the 'enable' option to turn that camera to being active.
I C R E A L T I M E S E C U R I T Y 4 Chapter S O L U T I O N S Appendix: Toxic or Hazard Materials Report Note This user manual is intended for reference only. Slight differences may be found in the user interface as products continually develop. All designs and software herein are subject to change without prior written consent. All trademarks and registered trademarks mentioned are the properties of their respective oweners. Please visit http://www.icrealtime.
