IBM - PCI - WL2 Installation Guide
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Read This First Before installing the network adapter: If your OS is Windows NT 4.0, go into the BIOS setup and set PnP OS field to NO. If your OS is Windows 98 2nd edition, go into the BIOS setup and set PnP OS field to YES. If your OS is Windows 2000 Professional, go into the BIOS setup and set PnP OS field to YES. If your OS is Windows NT4.0 and Wake on LAN capability is needed, go into the BIOS setup and enable power-up when a specific command is received by the Network Interface.
Connecting to a Novell NetWare 5.1 or 4.11 Server Microsoft Windows NT 4.0 Workstation Requirements Operating System Windows NT 4.0 Workstation Driver Version 5.33.00.0040 Driver File IBMTRP.SYS Server OS NetWare 5.1 or 4.11 Server Client OS Client v4.80 for Windows NT/2000 Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
14. Additional changes in the network properties, such as: workgroup name, computer name, TCP/IP properties, etc. may be necessary. Ask your Network Administrator for more information. 15. Click on “Close” to complete the installation. 16. Remove the driver disk and click on “Yes” when prompted to restart your computer. 17. Logon to Windows with administrator privileges. 18. From the location of the “Novell Client v4.80 for Windows NT/2000” installation files, execute “SETUPNW.EXE”. 19.
Connecting to a Microsoft Windows 2000 Advanced or NT 4.0 Server Microsoft Windows NT 4.0 Workstation Requirements Operating System Windows NT 4.0 Workstation Driver Version 5.33.00.0040 Driver File IBMTRP.SYS Server OS Windows 2000 Advanced or NT 4.0 Server Client OS Microsoft Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
14. Additional changes in the network properties, such as: workgroup name, computer name, TCP/IP properties, etc. may be necessary. Ask your Network Administrator for more information. 15. Click on “Close” to complete the installation. 16. Remove the driver disk and click on “Yes” when prompted to restart your computer. 17. Logon to Windows with administrator privileges and re-install the current service pack.
Connecting to a Novell NetWare 5.1 or 4.11 Server Microsoft Windows 98 2nd edition Requirements Operating System Windows 98 2nd edition Driver Version 5.33.00.0050 Driver File IBMTRP5.SYS Server OS NetWare 5.1 or 4.11 Server Client OS Client v3.30 for Windows 95/98 Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
15. Click on “Yes” to accept the “Novell Terms and Conditions”. 16. Select either “Typical” or “Custom” and click on “Install”. Typical Installation is normally chosen. Select Custom Installation only if you are an administrator or an advanced user. When prompted for options during installation, ask your Network Administrator for more information. 17. Click on “Reboot” once the Novell client installation is complete. Known Problems Problem1 There is an issue with waking up the system.
Connecting to a Microsoft Windows 2000 Advanced or NT 4.0 Server Microsoft Windows 98 2nd edition Requirements Operating System Windows 98 2nd edition Driver Version 5.33.00.0050 Driver File IBMTRP5.SYS Server OS Windows 2000 Advanced or NT 4.0 Server Client OS Microsoft Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
Known Problems Problem1 There is an issue with waking up the system. Currently there is no resolution to the problem. However, the problem can be prevented by not placing the system on Stand by. Also, the Power Management properties’ "Turn off monitor:" and “System standby:” settings must be set to “Never”.
Connecting to a Novell NetWare 5.1 or 4.11 Server Microsoft Windows 2000 Professional Requirements Operating System Windows 2000 Professional Driver Version 5.22.03.0050 (Embedded in OS) Driver File IBMTRP.SYS Server OS NetWare 5.1 or 4.11 Server Client OS Client v4.80 for Windows NT/2000 Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
12. Click on “Reboot” once the installation is complete. Known Problems Problem1 When the system wakes up from standby, the monitor does not turn back on. As a workaround the problem, after the computer wakes up from Standby, move the mouse or press a key on the keyboard to get a display from the monitor.
Connecting to a Microsoft Windows 2000 Advanced or NT 4.0 Server Microsoft Windows 2000 Professional Requirements Operating System Windows 2000 Professional Driver Version 5.22.03.0050 (Embedded in OS) Driver File IBMTRP.SYS Server OS Windows 2000 Advanced or NT 4.0 Server Client OS Microsoft Procedure 1. With the HP Vectra turned off, install the network adapter into an available PCI slot. 2. Connect the network cable to the newly installed network adapter. 3.
