Flat Panel Monitor 15.0 inch(381mm) TFT LCD 1024 x 768 Addressability 16.
T55A.book Page 1 Saturday, August 29, 1998 10:37 AM These user’s setup instructions cover typical user environments. The on-screen messages may differ depending on the level of your hardware and software. In some cases you may need to vary the setup procedures. For more information, refer to your computer or operating system manuals or consult your system administrator or dealer. Ces instructions de configuration d’exploitation s’appliquent aux environnements d’utilisation types.
T55A.book Page c Saturday, August 29, 1998 10:37 AM DANGER To avoid shock hazard: • • • • • • Do not remove the covers. Do not operate this product unless the stand is attached. Do not connect or disconnect this product during an electrical storm. The power cord plug must be connected to a properly wired and grounded power outlet. Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets.
T55A.book Page d Saturday, August 29, 1998 10:37 AM GEVAAR Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen: • • • • • • Verwijder in geen enkel geval de kap. Stel dit produkt alleen in werking als de voet is bevestigd. Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens onweer. Het netsnoer moet worden aangesloten op een geaarde contactdoos met correcte bedrading.
T55A.book Page e Saturday, August 29, 1998 10:37 AM PERIGO Para evitar o perigo de choques eléctricos: • • • • • • Não retire as coberturas. Não utilize este produto antes de montar a base. Não ligue nem desligue este produto durante uma tempestade eléctrica. O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente ligada à terra. Qualquer equipamento ligado a este produto deve estar ligado a tomadas eléctricas devidamente ligadas à terra.
T55A.book Page f Saturday, August 29, 1998 10:37 AM VAARA Sähköiskun vaaran välttämiseksi: • • • • • • Älä avaa laitteen kansia missään tilanteessa. Älä käytä laitetta, ellei jalustaa ole kiinnitetty. Älä kytke laitetta pistorasiaan tai irrota sitä pistorasiasta ukonilman aikana. Virtajohto on kytkettävä asianmukaisesti johdotettuun ja maadoitettuun pistorasiaan. Kaikki muutkin laitteet, joihin tämä tuote on liitetty, on kytkettävä asianmukaisesti johdotettuihin pistorasioihin.
2 2 2 2 3 4 4 5 5 DEUTSCH Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handling Instructions . . . .
T55A.book Page 2 Wednesday, September 16, 1998 10:32 AM Setup Hardware Requirements This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support XGA 1024 × 768, SVGA 800 x 600, or VGA 640 x 480 at 60 Hz. Workplace Preparation This section gives advice on what you should consider before you set up your monitor. Height The monitor should be positioned so that the top of the screen is slightly below your eye level when you sit at your workstation.
ENGLISH T55A.book Page 3 Wednesday, September 16, 1998 10:32 AM Back FRANÇAIS You should sit back in your chair and use the backrest. Hands Use a light touch on the keyboard, keeping your hands and fingers relaxed. Allow a space in front of the keyboard to rest your wrists when not typing. Consider using a wristpad. Screen settings Set the screen brightness and contrast to a comfortable level. You may have to adjust this as the lighting changes during the day.
T55A.book Page 4 Wednesday, September 16, 1998 10:32 AM Connecting your Monitor Be sure to read the ‘Safety Information’ at the front of this User Guide before carrying out this procedure. 1. Turn off your PC and all attached devices. 2. Connect the signal cable to the video port on the back of your computer. This port might be directly attached to your computer (figure A), or it might be part of a video adapter card (figure B).
ENGLISH T55A.book Page 5 Wednesday, September 16, 1998 10:32 AM FRANÇAIS Adjusting the Monitor Position Viewing Angle ESPAÑOL DEUTSCH You can tilt the screen backward and forward as shown below. Caring for your Monitor • Remove finger marks and grease with a damp cloth and mild detergent; do not use solvents or abrasives. • Never use flammable cleaning material to clean your IBM monitor or any other electrical apparatus. JAPANESE Gently wipe the covers and the screen with a soft cloth.
T55A.book Page 6 Wednesday, September 16, 1998 10:32 AM Configuring your Monitor Automatic Setup The Setup Utility included on the setup diskette is for displaying dot patterns. They do not replace or modify the display driver. When you first use your monitor you must perform Automatic Setup (AUTO SETUP). This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing.
Locate the operating system installed on your PC in the table below and follow the appropriate instructions. You may choose to run AUTO SETUP for each operating system that you use. This means that if you sometimes use your monitor while running any version of Windows and sometimes also use it from within DOS (not a DOS window), you must run AUTO SETUP for both Windows and DOS. You may run versions of AUTO SETUP in any order.
T55A.book Page 8 Wednesday, September 16, 1998 10:32 AM Auto Setup for DOS If the monitor is in standby mode (STANDBY ON), it may automatically turn off while you are waiting for it to warm up. If this happens, switch off the monitor and switch it on again after a few seconds. 1. If you are using PC-DOS/ V, change to U.S. mode by typing ‘CHEV US’ and pressing ENTER at the command prompt. You must use DOS or OS.
ENGLISH T55A.book Page 9 Wednesday, September 16, 1998 10:32 AM If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed check: • that the video interface cable is connected properly. • the correct video adapter card is installed. • the correct supported display mode is selected for your PC. 2. Wait approximately 15 minutes, until the monitor warms up. 3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the screen. 4.
T55A.book Page 10 Wednesday, September 16, 1998 10:32 AM 10. Press the ESC key to return to Windows. You have completed the monitor setup for Windows. If you use other operating systems, perform the appropriate AUTO SETUP for those systems, also: see Auto Setup OS/2 on page 11 and Auto Setup for DOS on page 8.
ENGLISH T55A.book Page 11 Wednesday, September 16, 1998 10:32 AM Turn on the monitor first; then the PC. If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed check: • that the video interface cable is connected properly. • the correct video adapter card is installed. • the correct supported display mode is selected for your PC. Wait approximately 15 minutes, until the monitor warms up. 3. Insert the diskette labelled ‘IBM Monitor Installation Disk’ into the diskette drive. 4.
T55A.book Page 12 Wednesday, September 16, 1998 10:32 AM If the screen flickers, repeat the setup several times until the flicker is minimised, or adjust it manually by following Manual Setup on page 13. 16. When finished, the OSD main menu returns. Press the Exit button to exit from the OSD. 17. Press the ESCAPE key to return to the OS/2 Window. You have completed the monitor setup for OS/2.
1. Have your monitor turned on for about 15 minutes, until the monitor warms up. 2. Display the image you most frequently use on the screen. 3. Press the OSD Enter button the initial OSD menu. 4. Use an Arrow button ( or ) to select the IMAGE LOCK icon and press the OSD Enter button to access the function. 5. Using an Arrow button ( or ), select MANUAL, press and then press once to select COARSE. Left and right arrow adjustment indicators become illuminated (see page 17). 6.
T55A.
OSD Lock / Unlock This feature allows you to secure the current control settings, while allowing the user to adjust Brightness and Contrast, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by using the same procedure. COMPL & WARR JAPANESE ITALIANO ESPAÑOL DEUTSCH Push and hold the button for 10 seconds to Lock or to Unlock. When locked, a “LOCKED” message will be displayed. FRANÇAIS ENGLISH T55A.
T55A.book Page 16 Wednesday, September 16, 1998 10:32 AM On-screen display (OSD) controls The settings adjustable with the user controls are viewed through the OnScreen Display (OSD). Press any of the OSD buttons to activate the OSD. The LCD monitor needs time to become thermally stable the first time you turn it on each day. Thus, to achieve more accurate adjustments for parameters, allow the LCD monitor to warm up (be On) for at least 15 minutes before making any screen adjustments.
ENGLISH T55A.book Page 17 Wednesday, September 16, 1998 10:32 AM • • Display Size Fine Coarse NORMAL - Image at normal size. If your computer or video board supplies a signal rate and addressability lower than 1024 × 768, this LCD monitor provides a scaling processor that can expand the addressability up to 1024 × 768. Moves the screen left and right or up and down. Use the Arrow buttons to adjust away the interference.
T55A.book Page 18 Wednesday, September 16, 1998 10:32 AM OSD Icon Description Resets the Brightness, Contrast and Color settings.
The display mode the monitor uses is controlled by the computer. Therefore, you should refer to your computer documentation for details on how to change display modes. The image size, position and shape may change when the display mode changes. This is normal and the image can be readjusted using AUTO SETUP and the monitor controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, TFT technology is inherently flicker-free.
T55A.book Page 20 Wednesday, September 16, 1998 10:32 AM Power Management If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT monitor temporarily until you have reconfigured the computer, preferably to 1024 x 768 at 60Hz.
No power to monitor Screen is blank and power indicator is steady green Brightness and Contrast may be too low Adjust brightness and contrast. The monitor is in the Power Management Standby state Press any key on the keyboard or move the mouse to restore operation.
T55A.book Page 22 Wednesday, September 16, 1998 10:32 AM Possible Cause Suggested Action The monitor is not receiving a video signal Check that the signal cable is firmly connected to the computer. Check that no pins are bent in the signal cable connector. Display mode of the computer is outside the range of the monitor Reconfigure the computer to use a supported display mode. Screen is blank and power indicator is flashing amber every 0.
ENGLISH T55A.book Page 23 Wednesday, September 16, 1998 10:32 AM If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM HELPCENTER. FRANÇAIS Further Help In the US call 1-800-772-2227 In other countries contact your dealer, retailer, or other IBM authorized Servicer. http://www.pc.ibm.com/us/ accessories Information about the Video Electronics Standards Association can be found on the worldwide web at: 2. Purchase receipt. 3. Description of problem.
T55A.book Page 24 Wednesday, September 16, 1998 10:32 AM 2. Carefully insert the head of a flathead (–) screwdriver into the slot visible along either side of the cable cover (a) and pry it off. 3. Squeeze the sides of the hinge cover (b) and pull it off. 4. Gently lift the stand cover (c) along the top and then slide it backwards and off the stand. 5. Remove the signal cable and the power cord from the monitor by disconnecting the corresponding adapters.
11. Put the hinge cover back on, making sure that the straight side is at the top. FRANÇAIS 12. Insert the three tabs at the top of the cable cover into the slots in the back of the monitor and push the cover into place. ENGLISH T55A.
T55A.book Page 26 Wednesday, September 16, 1998 10:32 AM Specifications This color monitor (Type-model 9513-Axx) uses a 15-inch TFT LCD. Dimensions Width: Depth: Height: Weight Power consumption figures are for the monitor and the power supply combined. 14.3 lb. (6.5 Kg) Tilt Forward Tilt: Backward tilt: – 4° + 41° Image Viewable Image Size: Maximum Height: Maximum Width: Pixel Pitch: 15.0” (381 mm) 228 mm 304 mm 0.297 mm (H) × 0.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
T55A.book Page II Wednesday, September 16, 1998 10:32 AM For units intended to be operated at 230 volts (U.S. use): Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG, type SVT or SJT, three conductor cord, a maximum of 4.5 meters (15 feet) in length and a tandem blade, grounding type attachment plug rated 15 amperes 250 volts. For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding type attachment plug rated 13 amperes (minimum), 250 volts.
FRANÇAIS DEUTSCH This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 / European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices.
T55A.book Page IV Wednesday, September 16, 1998 10:32 AM Warranty For European warranty terms and conditions, refer to the enclosed IBM Warranty statement, Part Number 72H9623. Statement of Limited Warranty The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use, and not for resale, from IBM or your reseller.
Warranty Service To obtain warranty service for the Machine, you should contact your reseller or call IBM. In the United States, call IBM at 1-800-772-2227. In Canada, call IBM at 1-800-565-3344. You may be FRANÇAIS If you transfer a Machine to another user, warranty service is available to that user for the remainder of the warranty period. You should give your proof of purchase and this Statement to that user. However, for Machines which have a life-time warranty, this warranty is not transferable.
T55A.book Page VI Wednesday, September 16, 1998 10:32 AM For European warranty terms and conditions refer to enclosed IBM warranty statement Part Number 72H9623. Référez-vous à la garantie IBM N° de référence 72H9623 pour les condtions de garantie européennes. Die europäischen Garantiebedingungen finden Sie in der beigefügten IBMGewährleistungserklärung, Teilenummer 72H9623.
