User’s Manual PPC-1510PT 15.
Ⅰ.
Ⅱ. Panel PC Specifications ◆ Display - 15.1" color TFT flat panel ◆ Display Type - TFT LCD panel ◆ Luminance – 200-250 cd/m2 brightness luminance ◆ CPU - P-III equivalent Low power 667Mhz CPU L1 & L2 cache built on CPU ◆ System Chipset - Twister-T , VIA VT8606 , 82C686B ◆ Front Bezel - Thick 10mm Aluminum-alloy hairline anodizing treatment front bezel ◆ Housing & Wall-mounting - Rugged 1.
Ⅲ. Power Supply Input : 100-240VAC ~ 2A 50/60Hz DC Output : +5V/7A, +12V/1.5A -12V/0.3A, +5Vsb/0.75A Ⅳ. NAGASAKI Panel PC Comparison table Model no.
Ⅴ. Touch Panel 1. Application 2. Warranty 3. Features 4. Characteristics 4.1 Usable Temperature Range 4.2 Storage Temperature Range 4.3 Input Method 5. Electrical Specifications 5.1 Linearity 5.2 Insulation Resistance 5.3 Chattering Time 6. Mechanical Specifications 6.1 Operating Force (with pen) 6.2 Surface Hardness 7. Optical Specifications 7.1 Light Transmittance 8. Reliability 8.1 Line drawing operation 8.2 Pen hitting operation 9. Environment Durability Performance 9.1 High Temperature Test 9.
11. Cautions 1. Application : This specification is applied to 6wire Touch Panel. 2. Warranty : TOUCH PANEL products manufactured to this specification shall be capable of meeting all characteristics for a minimum period of 12 months the date of shipping from NAGASAKI IPC when stored or used as specified under normal conditions within the contents of these sheets. If TOUCH PANEL products are not stored or used as specified herein, it will be void the 12 months warranty. 3.
. Optical Specifications 7.1 Light Transmittance (Total Transmittance)：More than 78%（Measuring apparatus： Haze meter-made by BYK-Gardner Type：Haze–Gard-plus 4726 Illuminant：CIE-A Standard：ASTM D 1003） 8. Reliability Item No. Item Ratings Test Methods & Condition 8-1 Line drawing operation 1,000,000 times of drawing Requirement in paragraph 5 and 6 Drawing must occur in following manner at any point within an Action area. 1) Testing equipment：Pen plotter 2) Testing load / force：2.
10.2 Criterion The followings are applied to viewing area The item 10.2 (1,2,3,4) should apply to the VA (view area) unless none VA affect electrical performance (1) Scratch Width ≦ 0.1mm and length ≦ 20mm：Accept . Width > 10 mm or Length > 20mm ：Reject (2) Granular foreign object Diameter ≦ 0.5mm：Acceptable 0.5mm ＜ Diameter：Unacceptable (3) Linear foreign object (fiber) Width ≦ 0.05 and Length ≦5mm：Accept Width ≧ 0.05 and Length ＞ 5mm：Unacceptable (4) Blistering (Puffiness, Baggy) Check through any 0.
Ⅵ. NASA-6109 User’s Manual Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to the this document and/or the product at any time without prior notice.
CPU Supporting Embedded VIA EDEN ESP5000 (533MHz) or VIA c3 800MHz CPU LAN Adapter Realtek 8139C or Intel 82559ER Audio Adapter *Optional VGA Adapter On chip 2D/3D Graphic Controller w/ SMA up to 8MB LCD Supporting TFT TTL LCD optional LVDS l ROM-Disk Socket Yes (2-288MB) TV-Out Optional I/O Port 4S/2P IDE Interface U. DMA 33/66/100 DIMM Socket 1 Max.
with the option of the higher performed VIA C3 800MHz CPU. For easier assembly and better integration without arranging array of cables, NASA-6109 provides onboard connectors with a similar conventional ATX layout. NASA-6109 provides the option of integrating Watch Dog Timer for ideal unattended terminals. To offer better flexibility, it also provides the options of riser card for PCI or ISA expansion through a 188-pin slot.
◆ Windows 95 OSR-2 VXD and integrated Windows 98 / NT5 miniport driver support ◆ BIOS shadow at 16KB increment ◆ Supports 2, 4 and 8 Mbytes of Frame Buffer with share memory. ◆ DirectDrawTM and DirectVideoTM Hardware Support ◆ Advanced Mobile Power Management ◆ CRT Power Management (VESA™ DPMS) Optional for Flat Panel Interface ( TTL or LVDS ) The board is designed to support industry standard TFT panel via 44pin connector or LVDS transmitters. The interface supports both 18-bit and 24-bit display modes.
◆ LCD cable (Optional) ◆ IDE Driver includes: Drivers for Windows NT 3.x / 4.x, Windows 95, 98, 2000, Win Me, Linux, Novell Netware and AMI FLASH ROM utilities. ◆ Driver utilities for on-board VGA drivers, LAN adapter and DOC 2000 If any of these items are missing or damage, please contact the dealer from whom you purchase the motherboard. Save the shipping material and carton in the event that you want to ship or store the board in the future.
Chapter 2.
Function Jumpers/Connectors External Speaker JP12: Pin 3, Pin 6 Buzzer On/Off JP12: Pin 4, Pin 5 Hardware Reset Switch JP12: Pin 7, Pin 8 External Power Good JP12: Pin 9, Pin 10 Internal Power Good JP12: Pin 10, Pin 11 ATX Power Supply On/Off Switch JP12: Pin 12, Pin 13 Power LED JP12: Pin 14, Pin 15 WDT Function Enable/Disable JP12: Pin 19, Pin 20 Please double-check the insertion and orientation of the LCD cable before applying power : mproper installation will result in permanent damage
JP9 (COM1, 2) / JP4 (COM3, 4) Voltage Selector: Voltage COM1(JP9) COM2(JP9) COM3(JP4) COM4(JP4) +12V(dc) 1-2 7-8 1-2 7-8 R.I. 3-4 9-10 3-4 9-10 +5V(dc) 5-6 11-12 5-6 11-12 JP10, JP11: RS232 / 422 / 485 Selector for COM2 TYPE JP10 JP11 RS-232 1-2, 4-5, 7-8, 10-11 1-2 RS-422/485 Full Duplex 2-3, 5-6, 8-9, 11-12 3-4, 7-8 * Make sure the port mode is set up correctly before installing any peripherals.
7-8 Hardware RESET 9-10 Reserved 10-11 Reserved 12-13 ATX Power On/Off 14-15 Power LED (14:LED+, 15:LED-) 16-17 Close for PS/2 Power 17-18 Close for ATX Power 19-20 Close: Enable WDT function J1: IR Pin Header. Pin No. Function 1 +5V(DC) 2 N.C. 3 IRRX 4 GND. 5 IRTX CN1: Audio Output Port connector via AV Card Kit (Optional) Please close pin13-14 to disable onboard Audio features if the AV Card Kit is not inserted onto the CN1 connector.
17 JBCY 18 JAB2 19 JBCX 20 JAB1 21 JACY 22 JBB2 23 JACX 24 JBB1 25 MSO 26 MSI CN7: Pin Header for PS2 KB / MS Pin No. Signal (KB) Pin No. Signal(MS) 1 KB Data 2 MS Data 3 KEY 4 KEY 5 GND 6 GND 7 +5V(DC) 8 +5V(DC) 9 KB_CLK 10 MS_CLK Printer (LPT1/LPT2) Port Pin No. Description Pin No.
Close for Normal Type * Caution: Improper setting will damage LCD panel. CN5: LCD - LVDS Output. Pin No. Signal Pin No. Signal 1 Y0- 2 Y2- 3 Y0+ 4 Y2+ 5 Y1- 6 Rcv. Voltage 7 GND 8 Y3- 9 Y1+ 10 Y3 11 CK- 12 VDD_PNL 13 CK+ 14 DISP_OFF 15 VBL 16 GND LCD_CON1: TFT LCD Panel Port Pin No. Signal Pin No.
31 FPD 1 32 FPD 0 33 GND 34 GND 35 P_CLK 36 FLM 37 DE 38 LP 39 GND 40 PBKL 41 PNKL 42 KEY 43 VCC 44 VCC * Please make sure the Pin 1 location before inserting the LCD connector. Factory Setting: JP1: All Pin Open JP7: Close Pin 1-3, Pin 4-6 JP8: Close Pin 1-2 JP13: Factory Using only JP14: Close Pin 2-3; Pin 5-6; Pin 8-9; Pin 11-12 JT1: Close Pin 2-3; Pin 4-5; Pin 8-9 JH1: Close Pin 1-2; Pin 5-6; Pin 7-8 2-4.
There are two different riser cards that can be fitted to NASA-6109 CPU board. The first one is a 98pin ISA only Bus riser card (traditional ISA Bus riser card), the second one is a 188pins PCI/ISA riser card. Please note: PCI/ISA riser cards jumper settings have to be matched with the motherboard INT/AD-select jumper. The default INT/AD-select for NASA-6109/3601M All-In-One motherboard is listed in the above table. However, it could be revised by changing JP14 setting for different INT/AD-select.
An IRQ number is automatically assigned to PCI expansion cards after those used by Legacy and PnP ISA cards. In the PCI Bus design, the BIOS is automatically assigned an IRQ to a PCI slot that has a card in it which requires an IRQ. To install a PCI card, you need to set the correct "ADSEL" and "INT" (interrupt) assignment. Please refer to "Chapter 2-5" Installing a Riser Card for detail assignments.
Chapter 3.
Choose “Auto Configuration with Optimal Setting”from the menu for loading the defaults parameters that is set by the manufacturer for the most stable normal configuration. Press F10 or “Save Setting and Exit”to save the changes and reboot the system. 3-2. Description of the BIOS Setup Option Please make clear the means of those optional parameters. Improper settings will cause the system to hang up or perform poorly. Most items are clearly understood from the screen prompt or “Help”by function key “F1”.
D400, 16k Shadow Disabled D800, 16k Shadow Disabled DC00, 16k Shadow Disabled S.M.A.R.T. For Hard Disks Set this option to “Enabled”to permit AMIBIOS to use the SMART (System Management System Management and Reporting Technologies) protocol for reporting server system information over a network. The settings are “Enabled”or “Disabled”. Password Check This option enables password checking every time the system boots or when you run AMIBIOS Setup.
AGP Mode 4x AGP Read Synchronization Enabled AGP Fast Write Disabled AGP Aperture Size 128MB AGP Master 1 W/S Write Disabled AGP Master 1 W/S Read Disabled PCI Delay Transaction Enabled USB Controller All USB Port USB Device Legacy Support All Device Configure SDRAM Timing by SPD SPD (Serial Presences Detect) is a device in memory module for storing the module information such as DRAM timing and chip parameters.
This function allows adjusting AGP Aperture Size from 2MB to 256MB to increased VGA performance.
SB IRQ Select 5 SB DMA Select 1 MPU-401 Enabled MPU-401 I/O Address 330h-333h FM Port (388h-38Bh) Enabled Game Port (200h-207h) Enabled Onboard FDC Set this option to “Enabled”to enable the floppy drive controller on the motherboard. The settings are Auto (AMIBIOS automatically determines if the floppy controller should be Enabled, or Disabled). Onboard Serial Port 1/2/3/4 This option specifies the base I/O port address of serial port.
EPP Version This option specifies the Enhanced Parallel Port specification version number that is used in the system. This option only appears if the Parallel Port Mode option is set to EPP. The settings are 1.7 or 1.9. Parallel Port IRQ This option specifies the IRQ used by the parallel port. The settings are Auto, (IRQ) 5, or (IRQ) 7. Parallel Port DMA Channel This option is only available if the setting for the Parallel Port Mode option is ECP. This option sets the DMA channel used by the parallel port.
Allows you to Enable / Disable onboard MIDI port, Game Port (200h-270h) This option allows configuring onboard Game port address. The choices: Disabled; 200h; 207h 3-6.
This option specifies the power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired. The settings are Disabled, Standby, or Suspend. Standby/Suspend Timer Unit This option specifies the unit of time used for the Standby and Suspend timeout periods. The settings are 4 msec, 4 sec, 32 sec, or 4 min. Display Activity When set to Monitor, this option enables event monitoring on the video display.
DMA Channel 6 PnP DMA Channel 7 PnP IRQ3 ISA/EISA IRQ4 SA/EISA IRQ5 PCI/PnP IRQ7 ISA/EISA IRQ9 PCI/PnP IRQ10 PCI/PnP IRQ11 PCI/PnP IRQ14 PCI/PnP IRQ15 PCI/PnP Plug and Play Aware O/S Set this option to Yes to inform AMIBIOS that the operating system can handle plug and Play (PnP) devices. The settings are No or Yes. The Optimal and Fail-Safe default settings are No. Display Device Select the display device for system. The available options are CRT Only, CRT + LCD.
These options allow you to specify the bus type used by each DMA channel. The settings are PnP or ISA/EISA . 3-8. Hardware Monitor Setup Provide some information such as CPU temperature, speed of cooling fan and usage voltage of CPU for user. Chapter 4. VGA, LCD, DOC Featur 4-1. AGP-BUS VGA Feature The NASA-6109 built-in Graphics Controller is a fully integrated 64-bit 2D/3D Accelerator.
external LVDS transmitters to support TFT LCD Panel with LVDS built-in. The flat panel interface provides or supports the following functions for various panels: - Generates flat panel interface signals like FLM, LP, SCLK, and DE - Generates different video data formats to directly drive different types of panels - Vertical and horizontal expansion of video displays to LCD panel resolution - Vertical and horizontal centering - Panel power sequence 4-3.
JP15 Memory Address 1-2 0C800H - 0C9FFH 1-2 0CC00H - 0CDFFH 3-4 0DCCCH - 0D1FFH 3-4 0D400H - 0D5FFH 5-6 0D800H - 0D9FFH 4-5. Driver Utility Installation Guide 1. When finishing with the Windows platform (95/98/2000/NT) installation, please install the relative VIA driver (4in1) utilities for compliance of the compatibility with hardware environment. 2.
4. Select VIA 4in1 service pack driver install to the system 5. The Screen will appear VIA 4in1 driver setup screen, please press “NEXT”to continue. Please follow the steps instructed by each screen for the installation of the VIA 4in1 driver. Restart the system after the completion of the installation. 6. After VIA 4in1 driver installed, please select VGA driver for install. The system will request for “restart”after the completion of the driver installation. 7.
Chapter 5. LAN Adapter The on-board LAN adapter use of Single Chip Fast Ethernet Controller, that is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory. The On-board LAN adapter can directly fetch the system CPU. Also, it can transfer data Directly between I/O devices and system memory in the 32-bit bus master mode that provides low CPU utilization. It complies with the IEEE 802.
Twisted Pair Pin Signal Pin Number Number Signal To Number Description Description 1 TD+ 2 TD- 3 RD+ 6 RD- 1 2 à à 1 TD+ 2 TD- 3 RD+ 6 RD- RJ-45 Connector Pin Assignments Figure A-1 shows the RJ-45 Connector pin assignments 5-3. Connecting 100Base-TX Fast Ethernet Network The system board provides an RJ-45 port for connection to 100Base-TX Fast Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP).
10Mbps network only. - Category 5 cable is also good for 10Mbps operation. Use UTP Category 5 cable for the versatility to operate the network at either 100Mbps or 10Mbps speed without changing cable. - Two pairs of wiring are required. - Depending on building codes, different insulation materials may be required. Plenum-rated or TEFLON-coated wiring maybe required in some areas where fire proofing is required.
5-7. LED Indicators The system board comes with two LED indicators on the edge of the motherboard that indicates the network system status. If you experience any problems with the adapter, first make sure the appropriate driver is loaded, the proper cable is connected to the RJ-45 port and the hub complies with the adapter specification, such as 10Mbps 10Base-T or 100Mbps 100Bast-TX. Finally, recheck the LEDs.
>> A:\REST8139.EXE 1. View Current Configuration This allows you to find the PCI Fast Ethernet adapter current configuration in your system. 2.
Software Installation Examples Before installing the driver programs, please refer to each directory that contains a README file, which provides detailed installation instructions, or to execute the HELP8139.EXE help file viewer in DOS. The utility will then present with a screen showing the information about how to install the network driver. Driver needed for the adapter to work with the operating system. 5-9.
---- Screen Message ---DOS/4G Protected Mode Run-time Version 2.01a Copyright © Tenberry Software, Inc. 1996 Please wait for loading BIOs ROM … . AMI Flash Utility V8.27.25 Flash ROM Programming report Chipset Vendor : VIA Flash ROM : IC Brand Chipset Code : VIA686A/B Vendor : IC P/N ROM Filename : xxxx.ROM Flash ROM Code : 512kb Boot Block Programming : Yes ROM File Size >>>>>>>>>>>>>>>>>>>>>>… … Verify ROM data Now… . Flash ROM update Completed - Pass Please restart your system.
D-SUB Type Connector for COM port (RS232); Pin No. Description Pin No. Description 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND Box Header Type Connector for COM port (RS232); Pin No. Description Pin No. Description 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 N.C Printer (LPT1/LPT2) Port Pin No. Description Pin No.
Pin No. Description Pin No. Description 2 GREEN 10 GND 3 BLUE 11 N.C 4 N.C 12 DDC DAT 5 GND 13 H.Sync 6 GND 14 V.Sync 7 GND 15 DDC CLK 8 GND FDD Connector Pin No. Description Pin No. Description 1,3,5,7 GND 14 DSA# 9,11,13 GND 16 MOB# 15,17,19 GND 18 DIR 21,23,25 GND 20 STEP# 27,29,31 GND 22 WD# 33 GND 24 WE# 2 RWC# 26 TRAK0 4,6 N.
11 CK- 12 VDD_PNL 13 CK+ 14 DISP_OFF 15 VBL 16 GND TFT LCD Panel Port Connector (LCD-CON1) Pin No. Signal Pin No.
USB PORT Pin No. Description 1 2 USB VCC 3 4 USB DATA-(0,1/2,3) 5 6 USB DATA+(0,1/2,3) 7 8 USB_GND 9 10 USB_GND Audio Output Port Connector (CN1) Pin No. Function Pin No. Function 1 BITCLK 2 GND 3 SDIN 4 N.C. 5 SDIN2 6 N.C. 7 SDOUT 8 N.C.
IDE1, IDE2 Connector Pin No. Description Pin No. Description 2,19,22 GND 13 IDE data2 24.26.30 GND 14 IDE data13 40 GND 15 IDE data1 20,21,28 N.C 16 IDE data14 29,32,34 N.
Pin No. Description A Description B Description E Description F 11 AEN -SMEMW GND GND 12 SA19 -SMEMR PCLKE -REQ1 13 SA18 -IOW GND AD31 14 SA17 -IOR AD30 AD29 15 SA16 -DACK3 PCLKG N.C 16 SA15 DRQ3 KEY KEY 17 SA14 -DACK1 -GNT2 -REQ2 18 SA13 DRQ1 AD28 AD27 19 SA12 REFRESH AD26 AD25 20 SA11 SYSCLK AD24 -CBE3 21 SA10 IRQ7 AD22 AD23 22 SA9 IRQ6 AD20 AD21 23 SA8 IRQ5 AD18 AD19 24 SA7 IRQ4 N.C. N.C 25 SA6 IRQ3 KEY KEY 26 SA5 -DACK2 N.
Pin No.
