Eden/Ezra Processor User's Manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating jumpers
- 2.4 Locating Connectors
- 2.5 Setting Jumpers
- 2.6 Clear CMOS (JP4)
- 2.7 Installing DIMMs
- 2.8 IDE, CDROM hard drive connector (CN14, CN16)
- 2.9 Solid State Disk
- 2.10 Floppy drive connector (CN18)
- 2.11 Parallel port connector (CN15)
- 2.12 Keyboard and PS/2 mouse connector (CN25)
- 2.13 Power & HDD LED, Reset Button Connector (CN13, CN22)
- 2.14 Power connectors (CN27, CN5, FAN1)
- 2.15 ATX power control connector (CN3, CN23)
- 2.16 IR connector (CN24)
- 2.17 Audio interfaces (CN4, CN2)
- 2.18 COM port connector (CN19)
- 2.19 VGA/LCD/LVDS interface connections
- 2.20 TV-out interface (optional) (CN1)
- 2.21 Ethernet configuration
- 2.22 Watchdog timer configuration
- 2.23 USB connectors (CN20, CN28)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- 4.2.1 Entering setup
- 4.2.2 Standard CMOS Features setup
- 4.2.3 Advanced BIOS Features setup
- 4.2.4 Advanced Chipset Features setup
- 4.2.5 Integrated Peripherals
- 4.2.6 Power Management Setup
- 4.2.7 PnP/PCI Configurations
- 4.2.8 PC Health Status
- 4.2.9 Frequency/Voltage Control
- 4.2.10 Load Optimized Defaults
- 4.2.11 Set Password
- 4.2.12 Save & Exit Setup
- 4.2.13 Exit Without Saving
- Chapter 5 PCI SVGA Setup
- Chpater 6 Audio Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104-Plus Modules
- Appendix C Pin Assignments
- C.1 CPU Fan Power Connector (FAN 1)
- C.2 Ethernet 10/100Base-T Connector (CN12)
- C.3 Audio Connector (CN4)
- C.4 Audio In Connector (CN2)
- C.5 Main Power Connector (CN5)
- C.6 Keyboard and PS/2 Mouse Connector (CN25)
- C.7 Floppy Disk Drive Connector (CN18)
- C.8 PC/104 plus Connectors (CN17)
- C.9 IDE Hard Drive Connector (CN14, CN16)
- C.10 Parallel Port Connector (CN15)
- C.11 Power & HDD LED Connector(CN13)
- C.12 Reset Button Connector (CN22)
- C.13 USB Connector (CN20, CN28)
- C.14 LCD Inverter Backlight Connector (CN6)
- C.15 IR Connector (CN24)
- C.16 CRT Display Connector (CN8)
- C.17 TV (video) Out Connector (CN1)
- C.18 Flat Panel Connector (CN11)
- C.19 Extended Flat Panel Display Connector (CN10)
- C.20 LCD Signal Mapping
- C.21 LVDS Connector (CN9)
- C.22 Peripheral Power Connector (CN27)
- C.23 COM Port Connector (CN19)
- C.24 CompactFlash Card Connector (CN26)
- C.25 ATX Power Feature Connector (CN3)
- Appendix D System Assignments
- Appendix E Optional Extras for the PCM-9575
- Appendix F Mechanical Drawings
viii
Chapter 6 Audio Setup.....................................................75
6.1 Introduction ..................................................................... 76
6.2 DOS utilities.................................................................... 76
6.2.1 VIA Sound Blaster Pro compatible set up program................ 76
6.2.2 VIA Sound Blaster Installation ............................................... 77
6.3 Driver installation............................................................ 77
6.3.1 Before you begin ..................................................................... 77
6.3.2 Windows 95/98 drivers ........................................................... 78
6.3.3 Windows NT drivers ............................................................... 85
6.3.4 Windows 2000 Drivers............................................................ 88
Chapter 7 PCI Bus Ethernet Interface...........................93
7.1 Introduction ..................................................................... 94
7.2 Installation of Ethernet driver ......................................... 94
7.2.1 Installation for MS-DOS and Windows 3.1 ............................ 94
7.2.2 Installation for Windows 98 .................................................... 95
7.2.3 Installation for Windows 2000................................................ 98
7.2.4 Installation for Windows NT................................................. 103
7.3 Further information ....................................................... 109
Appendix A Programming the Watchdog Timer ...........111
A.1 Supported Input Timing Modes .................................... 112
Appendix B Installing PC/104-Plus Modules..................115
B.1 Installing PC/104-Plus Modules.................................... 116
Figure B.1: PC/104+ module mounting diagram............... 117
Figure B.2: PC/104+ module dimensions (mm) (±0.1) ..... 118
Appendix C Pin Assignments ...........................................119
C.1 CPU Fan Power Connector (FAN 1)............................. 120
C.2 Ethernet 10/100Base-T Connector (CN12)................... 120
C.3 Audio Connector (CN4)................................................ 121
C.4 Audio In Connector (CN2)............................................ 121
C.5 Main Power Connector (CN5) ...................................... 122
C.6 Keyboard and PS/2 Mouse Connector (CN25)............. 123
C.7 Floppy Disk Drive Connector (CN18) .......................... 124
C.8 PC/104 plus Connectors (CN17)................................... 125
C.9 IDE Hard Drive Connector (CN14, CN16) .................. 127
C.10 Parallel Port Connector (CN15) .................................... 128
C.11 Power & HDD LED Connector(CN13) ........................ 129
C.12 Reset Button Connector (CN22) ................................... 129
C.13 USB Connector (CN20, CN28)..................................... 130
C.14 LCD Inverter Backlight Connector (CN6).................... 130
C.15 IR Connector (CN24).................................................... 131
C.16 CRT Display Connector (CN8)..................................... 131