PCI-6871 PCI Eden400 Half-sized SBC with SODIMM/VGA LCD/LVDS/LAN and CFC2 Users’ Manual
Copyright This document is copyrighted, © 2002. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 ea. PCI-6871 all-in-one single board computer • 1 ea. startup manual • CD-ROM or disks for utility, drivers, and manual (in PDF format) • 1 ea. power cable p/n: 1703080101 • 1 ea. PS/2 KB/M cable p/n: 1700060202 • 1 ea. Printer cable p/n:1700260250 • 1 ea. FDD cable p/n:1701340603 • 1 ea.
PCI-6871 User’s Manual iv
Table of Contents Contents Chapter 1 General Information ........................................1 1.1 1.2 1.3 Introduction ....................................................................... 2 Features ............................................................................. 3 Specifications .................................................................... 3 1.3.1 1.3.2 1.3.3 1.3.4 1.3.5 1.4 Chapter Standard SBC Functions.................................................
2.19.2 2.19.3 2.19.4 2.19.5 2.20 Flat panel display connector (CN18) ............................ 21 Extension flat panel connector (CN17) ........................ 21 LVDS LCD panel connector (CN21) ........................... 21 Panel type selection (S1)............................................... 22 Ethernet configuration..................................................... 22 2.20.1 100Base-T connector (CN15)....................................... 23 2.20.2 Network boot ............................
Table of Contents 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.3 Chapter Further Information ......................................................... 73 6 Audio Setup.....................................................75 6.1 6.2 Introduction ..................................................................... 76 DOS utilities.................................................................... 76 6.2.1 6.2.2 6.3 VIA Sound Blaster Pro compatible set up program ..... 76 VIA Sound Blaster Installation.............
C.14 C.15 C.16 C.17 C.18 C.19 C.20 C.21 C.22 C.23 CRT Display Connector (CN12)................................... 131 Flat Panel Connector (CN18)........................................ 132 Extended Flat Panel Display Connector (CN17) .......... 133 LCD Signal Mapping .................................................... 134 LVDS Connector (CN21).............................................. 135 COM Port Connector (CN19, CN20)............................ 136 CompactFlash Card Connector (CN28) ..............
CHAPTER 1 General Information This chapter gives background information on the PCI-6871.
Chapter 1 Introduction 1.1 Introduction The new PCI-6871 is a half-sized CPU card with onboard VIA Eden400 C3 EBGA fanless CPU. The VIA Eden processor uses advanced 0.13µ CMOS technology with 128KB L1 cache memory and 64KB L2 cache memory on die. This board with Eden400 CPU can operate without a fan at temperatures up to 60° C (140° F) and typically consumes under 14 Watts while supporting numerous peripherals. This SBC includes a 4X AGP controller, a PCI Ethernet interface, and 36-bit TTL interface.
1.2 Features • Embedded low power VIA Eden C3 EGBA 400MHz processor • Half-sized CPU card with PCI golden finger • Fanless operation at 60° C. • 1 onboard RJ-45 connector supports 10/100Base-T Ethernet • 4X AGP graphics for high performance applications • Supports PC/104 • Supports wake on LAN • Supports wake on Modem • Supports LCD backlight turn-off function 1.3 Specifications 1.3.
• Keyboard/mouse connector: Supports standard PC/AT keyboard and a PS/2 mouse • Power management: Supports power saving modes including Normal/Standby/Suspend modes. APM 1.2 compliant • Watchdog timer: 62 level timer intervals • USB: Four universal serial bus ports • PC/104 expansion: PC/104 connector for ISA control board • Solid State Disk: Supports one 50-pin socket for CFC type I/II 1.3.
1.4 Board layout: dimensions + PCI-6871 REV.A1 I Figure 1.
PCI-6871 REV.A1 + Figure 1.
CHAPTER 2 Installation This chapter explains the setup procedures of PCI-6871 hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all safety precautions before you begin the installation procedure.
Chapter 2 Installation 2.1 Jumpers The PCI-6871 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumpers Label Function JP1 CMOS clear JP2 LAN power select JP3 RS-232/422/485 select JP4 Watch-Dog output selct S1 Panel type select 2.2 Connectors On-board connectors link the PCI-6871 to external devices such as hard disk drives, a keyboard, or floppy drives.
Table 2.
2.3 Locating jumpers + PCI-6871 REV.A1 I Figure 2.
2.4 Locating Connectors + PCI-6871 REV.A1 I Figure 2.
2.5 Setting Jumpers You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
2.6 Clear CMOS (JP1) Warning! To avoid damaging the computer, always turn off the power supply before setting “Clear CMOS.” Before turning on the power supply, set the jumper back to “3.0 V Battery On.” This jumper is used to erase CMOS data and reset system BIOS information. The procedure for clearing CMOS is: 1. Turn off the system. 2. Short pin 2 and pin 3. 3. Return jumper to pins 1 and 2. 4. Turn on the system. The BIOS is now reset to its default setting Table 2.3: CMOS clear (JP1) *3.
2.7 Installing system memory (SODIMMs) You can install anywhere from 32 to 512 MB of SDRAM into your PCI-6871 Series card. The card provides two 144-pin SODIMM sockets. Each socket accepts 32/64/128/256/512 MB 3.3 V power level SODIMMs. If only one SODIMM module is installed, it may be installed in either SODIMM socket on the solder side of the PCI-6871 Series card. Note: PCI-6871 Series cards only support SDRAM SODIMM modules. EDO SODIMM is not supported. 2.7.
Important: Only use standard form SODIMM memory modules (as shown in the diagram below). Standardized dimensions ensure a proper fit. Check with your memory supplier about the SODIMM modules you will use. Figure 2.3: SODIMM module 2.8 IDE, CDROM hard drive connector (CN1, CN7) The PCI-6871 provides 2 IDE channels which you can attach up to four Enhanced Integrated Device Electronics hard disk drives or CDROM to the PCI-6871’s internal controller. The PCI-6871's IDE controller uses a PCI interface.
2.8.1 Connecting the hard drive Connecting drives is done in a daisy-chain fashion. It requires one of two cables (not included in this package), depending on the drive size. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5" drives use a 1 x 44-pin to 2 x 40-pin connector. Wire number 1 on the cable is red or blue, and the other wires are gray. 1. Connect one end of the cable to CN1 or CN7.
2.10.1 Connecting the floppy drive 1. Plug the 34-pin flat-cable connector into CN6. Make sure that the red wire corresponds to pin one on the connector. 2. Attach the appropriate connector on the other end of the cable to the floppy drive(s). You can use only one connector in the set. The set on the end (after the twist in the cable) connects to the A: drive. The set in the middle connects to the B: drive. 3. If you are connecting a 5.
standard PC/AT BIOS will report an error or fail during power-on selftest (POST) after a reset. The PCI-6871’s BIOS standard setup menu allows you to select “All, But Keyboard” under the “Halt On” selection. This allows no-keyboard operation in embedded system applications, without the system halting under POST. 2.13 Power & HDD LED, Reset Button Connector (CN13, CN8) Next, you may want to install external switches to monitor and control the PCI-6871.
2.15 ATX power control connector (CN3, CN5) 2.15.1 ATX feature connector (CN3) and soft power switch connector (CN5) The PCI-6871 can support an advanced soft power switch function, if an ATX power supply is used. To enable the soft power switch function: 1. Get the specially designed ATX-to-EBX power cable (PCI-6871 optional item, part no. 1703200100) 2. Connect the 3-pin plug of the cable to CN3 (ATX feature connector). 3. Connect the power on/off button to CN5.
2.16 IR connector (CN9) This connector supports the optional wireless infrared transmitting and receiving module. This module mounts on the system case. You must configure the setting through BIOS setup. 2.17 Audio interfaces (CN10) The Audio link is a 10 pin connector; the PCI-6871 can support AC97 Audio with the addition of optional PCM-231A-00A1. 2.18 COM port connector (CN19, CN20) The PCI-6871 provides two serial ports (COM1:RS-232; COM2: RS232/422/485) in one COM port connector.
2.19.1 CRT display connector (CN12) CN12 is a standard 15-pin D-SUB connector commonly used for VGA. The pin assignments for CRT display connector CN12 are detailed in Appendix C. 2.19.2 Flat panel display connector (CN18) CN18 consists of a 40-pin connector which can support a 24-bit LCD panel. It is Hirose’s product no. DF13A-40DP-1.25 V The PCI-6871 provides a bias control signal on CN18 that can be used to control the LCD bias voltage.
2.19.5 Panel type selection (S1) S1 is an 8 segment DIP switch for DSTN/TFT panel type and resolution functions. Table 2.4: S1 Panel Type select SW 1-1 SW 1-2 SW 1-3 SW 1-4 Panel Type & Resolution ON ON ON ON TFT 640x480** 18bit (H. V. Freq) ON ON ON OFF TFT 648x480 18bit (Synthetic) ON ON OFF ON TFT 648x480** N/A ON ON OFF OFF TFT 648x480** LVDS ON OFF ON ON DSTN 648x480** 18bit ON OFF ON OFF TFT 800x600** 18bit (H. V.
2.20.1 100Base-T connector (CN15) CN15 is an RJ-45 connector with LED.. 2.20.2 Network boot The Network Boot feature can be utilized by incorporating the Boot ROM image files for the appropriate network operating system. The Boot ROM BIOS files are included in the system BIOS, which is on the utility CD disc. 2.20.3 LAN controller power select (JP2) Table 2.5: LAN controller power select (JP2) 3.3 V* Standby 3.3V * default setting Note: PCI-6871 supports Wake-on-LAN.
Table 2.6: Watchdog timer action (JP4) *System reset IRQ 11 * default setting 2.22 USB connectors (CN4, CN23) The PCI-6871 board provides up to four USB (Universal Serial Bus) ports, with USB3 and USB4 optional. This gives complete Plug and Play, and hot attach/detach for up to 127 external devices. The USB interfaces comply with USB specification Rev. 1.1, and are fuse protected. The USB interface is accessed through two 5 x 2-pin flat-cable connectors, CN4 (USB1, 2); and CN23 (USB3, 4).
CHAPTER 3 Software Configuration This chapter details the software configuration information. It shows you how to configure the card to match your application requirements. The AWARD System BIOS is covered in Chapter 4. Sections include: • • • Introduction Connections for standard LCDs Ethernet interface configuration.
Chapter 3 Software Configuration 3.1 Introduction The PCI-6871 system BIOS and custom drivers are located in a 256 Kbyte, Flash ROM device, designated U18. A single Flash chip holds the system BIOS, VGA BIOS and network Boot ROM image. The display can be configured via CMOS settings. This method minimizes the number of chips and difficulty of configuration. To set different types of LCD panels, please choose “panel type” from the “integrated peripherals” menu in CMOS setup.
3.2 Connections to Three Standard LCDs The following tables illustrate typical LCD connection pinouts for the PCI-6871. 3.2.1 Connections to Toshiba LTM10C209A (640 x 480 TFT color LCD) Table 3.
Table 3.1: Connections to Toshiba LTM10C209A 28 B5 16 P7 29 GND 3 GND 30 VDD 1 +5 V 31 VDD 2 +5 V 3.2.2 Connections to Toshiba LTM15C151A (1024 x 768 TFT color LCD) Table 3.
Table 3.2: Connections to Toshiba LTM15C151A CN1-25 OB5 CN 10-13 PD34 CN1-26 ENAB CN 11-37 M/DE CN1-27 GND CN 11-34 GND CN1-28 VDD CN 11-1 +5V CN1-29 VDD CN 11-2 +5V CN1-30 GND CN 11-8 GND 3.2.3 Connections to Toshiba LTM12C275A (800 x 600 TFT color LCD) Table 3.
Table 3.3: Connections to Toshiba LTM12C275A 23 B3 14 P5 24 B4 15 P6 25 B5 16 P7 26 ENAB 37 M/DE 27 GND 34 GND 28 VCC 5 +5 V 29 VCC 6 +5 V 30 GND 39 GND 3.3 Ethernet software configuration The PCI-6871’s on-board Ethernet interface supports all major network operating systems. To configure the medium type, to view the current configuration, or to run diagnostics, do the following: 1. Power the PCI-6871 on. Make sure that the RSET8139.EXE file is located in the working drive.
Note For Ethernet installation, please see Chapter 7 31 Chapter 3 Software Configuration
PCI-6871 User’s Manual 32
CHAPTER 4 Chapter 4 Ducks that Need Love! Award BIOS Setup This chapter describes how to set BIOS configuration data.
Chapter 4 Award BIOS Setup 4.1 System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
4.2 Award BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. 4.2.1 Entering setup Power on the computer and press immediately. This will allow you to enter Setup. Figure 4.
4.2.2 Standard CMOS Features setup When you choose the Standard CMOS Features option from the Initial Setup Screen menu, the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the left bottom of the Menu screen. Figure 4.
4.2.3 Advanced BIOS Features setup By choosing the Advanced BIOS Features Setup option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCI-6871 Series. Figure 4.
4.2.4 Advanced Chipset Features setup By choosing the Advanced Chipset Features option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCI-6871 Series. Figure 4.
4.2.5 Integrated Peripherals Choosing the Integrated Peripherals option from the Initial Setup Screen menu should produce the screen below. Here we see the manufacturer’s default values for the PCI-6871 Series. Figure 4.5: Integrated Peripherals 4.2.6 Power Management Setup By choosing the Power Management Setup option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCI-6871 Series. Figure 4.
4.2.7 PnP/PCI Configurations By choosing the PnP/PCI Configurations option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCI-6871 Series. Figure 4.7: PnP/PCI Configurations 4.2.8 PC Health Status The PC Health Status option displays information such as CPU and motherboard temperatures, fan speeds, and core voltage. Figure 4.
4.2.9 Frequency/Voltage Control By choosing the Frequency/Voltage Control option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCI-6871 Figure 4.9: Frequency/Voltage Control Caution Incorrect settings in Frequency/Voltage Control may damage the system CPU, video adapter, or other hardware.
4.2.10 Load Optimized Defaults Load Optimized Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusable), these defaults will load automatically when you turn the PCI-6871 Series system on. Figure 4.10: Load BIOS defaults screen 4.2.
3. At the “Confirm Password” prompt, retype the desired password, then press . 4. Select Save to CMOS and EXIT, type , then . To Change Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press . 2. When you see “Enter Password,” enter the existing password and press . 3. You will see “Confirm Password.” Type it again, and press . 4.
4.2.13 Exit Without Saving Selecting this option and pressing lets you exit the Setup program without recording any new values or changing old ones.
CHAPTER 5 PCI SVGA Setup • • • Introduction Installation of SVGA drivers -for Windows 95/98/Me -for Windows NT/2000/XP Further information 45 Chapter 5 PCI SVGA Setup
Chapter 5 PCI SVGA Setup 5.1 Introduction The PCI-6871 has an onboard AGP flat panel/VGA interface. The specifications and features are described as follows: 5.1.1 Chipset The PCI-6871 uses a VIA TwisterT chipset from VIA Technology Inc. for its AGP/SVGA controller. It supports many popular LCD, and LVDS LCD displays and conventional analog CRT monitors. The VIA8606T VGA BIOS supports color TFT and DSTN LCD flat panel displays.
5.1.4 Dual/Simultaneous Display The PCI-6871 uses a VIA Twister VT8606T LCD controller that is capable of providing simultaneous dual view display of the same content on a flat panel and CRT. To set up dual view (simultaneus mode) under Windows 9x, Windows ME, Windows NT/2000/XP, follow these steps: Step 1. Open the Control panel, and select “Display”, “Settings”. Step 2. Select " CRT+LCD " or " CRT+TV " for dual view Step 3. Click “OK”. Figure 5.
5.2 Installation of the SVGA Driver Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your PCI-6871. Notes: 1. The windows illustrations in this chapter are intended as examples only. Please follow the listed steps, and pay attention to the instructions which appear on your screen. 2. For convenience, the CD-ROM drive is designated as "D" throughout this chapter. 5.2.
Step 2. Choose the "Adapter" tab, then press the "Change..." button. Step 3. Press the "Have Disk" button.
Step 4. Type in the path: D:\slotPC\6871\VGA\Win9x_Me D:\slotPC\6871\VGA\Win9x_Me Step 5. Select the highlighted item, and click the "OK" button.
Step 6. "S3 GraphicsTwister" appears under the adapter tab. Click the "Apply" button, then the "OK" button. Step 7. Press “Yes” to reboot.
5.2.2 Installation for Windows 98/Me Step 1. Select "Start", "Settings", "Control Panel", "Display", and "Settings," then press the "Advanced..." button.
Step 2. Select “Adapter,” then “Change.
Step 3. Press “Next,” then “Display a list....” Step 4. Press the “Have disk...” button.
Step 5. Insert the CD into the CD-ROM drive. Type in the path D:\slotPC\6871\VGA\Win9x_Me Then press “OK” D:\slotPC\6871\VGA\Win9x_Me Step 6. Select the highlighted item, then click “OK.
Step 7. "S3 Graphics Twister"appears under the adapter tab. Click the "Apply" button. Step 8. Press “Yes” to reboot.
5.2.3 Installation for Windows NT Note: Service Pack X (X = 3, 4, 5, 6,...) must be installed first, before you install the Windows NT VGA driver. Step 1. Select "Start", "Settings", "Control Panel" and double click the "Display" icon.
Step 2. Choose the "Settings" tab, and press the "Display Type" button.
Step 3. Press the "Change..." button.
Step 4. Click the "Have Disk..." button. Step 5. Type the path: D:\slotPC\VGA\WinNT Press the "OK" button.
Step 6. Select the highlighted item, and click the "OK" button. Step 7. Press "Yes" to proceed. Step 8. Press "OK" to reboot.
5.2.4 Installation for Windows 2000 Step 1. Select "System", "Settings", "Control Panel" and double click the "system" icon.
Step 2. Choose the "Video Controller (VGA Compatible)” button.
Step 3. Choose the "Drive" button, press “Update Driver...” button.
Step 4. Choose "Display a list of..." , then press “Next” button. Step 5. Choose “Display adapters”, press “Next” button.
Step 6. Click the “Have Disk” button. Step 7. Type the path D:\slotPC\6871\VGA\Win2000 press the “OK” button.
Step 8. Press “Finish" to reboot. 5.2.5 Installation for Windows XP Step 1. Select "System", "Settings", "Control Panel" and double click the "system" icon.
Step 2. Choose “Hardware” and “Device Manager”, press “OK” button.
Step 3. Choose “Video Controller (VGA Compatible), press “OK” button.
Step 4. Choose "Driver”, “Update Driver”, press “OK” button. Step 5. Choose “Install from a list.....” , press “Next”.
Step 6. Choose “Don’t search. I will....”, press “Next” button. Step 7. Choose “Display adapters”, press “Next” button.
Step 8. Type the path D:\slotPC\6871\VGA\WinXP then press “OK” button. D:\slotPC\6871\VGA\Win2000 Step 9. Choose “S3 Graphics Twister + S3 Hotkey” then press “Next” button.
Step 10. Press “Finish" to reboot. 5.3 Further Information For further information about the AGP/VGA installation in your PCI6871, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: VIA website: www.via.com.tw manufacturers website: www.emacinc.
PCI-6871 User’s Manual 74
CHAPTER 6 Audio Setup The PCI-6871 is equipped with an audio interface that records and plays back CD-quality audio. This chapter provides instructions for installing the software drivers included on the audio driver diskettes.
Chapter 6 Audio Setup 6.1 Introduction The PCI-6871 supports AC97 audio through the optional audio module PCM-231A-00A1. 6.2 DOS utilities 6.2.1 VIA Sound Blaster Pro compatible set up program Please "Enable" the Sound Blaster setting in the BIOS before playing Sound Blaster compatible DOS games.
Step 3. The program will copy the relative files into the directory which you assign. Next, the program will insert the following new line into the AUTOEXEC.BAT and copy the original AUTOEXEC.BAT to AUTOEXEC.VIA. C: \VIAUDIO\VIAUDIO.COM Step 4. Reboot the system when the installation is complete. Step 5. Uninstall by deleting the new line from the AUTOEXEC.BAT. 6.3 Driver installation 6.3.1 Before you begin Please read the instructions in this chapter carefully before you attempt installation.
Step 1. Click "Start" and select "Settings". Click "Control Panel" and double-click "Add New Hardware". Step 2. In the Add New Hardware Wizard window, click "Next".
Step 3. In the following Add New Hardware Wizard window, click "Next" for Windows to search for Plug and Play devices. Step 4. In the following Add New Hardware Wizard window, select "No, the device isn't in the list."and click "Next".
Step 5. In the following Add New Hardware Wizard window, select "No, I want to select..." and click "Next". Step 6. In the following Add New Hardware Wizard window, select "Sound, video and game controllers" and click "Next".
Step 7. In the following Add New Hardware Wizard window, click "Have Disk...". Step 8. In the Install From Disk window, click "Browse".
Step 9. In the Open window, select "D:\slotPC\6871\Audio\98se_Me_2k_xp\WIN95_98. Step 10. In the Install From Disk window, click" OK".
Step 11. In the Select Device window, select "VIA PCI Audio Controller (WDM)" and click "OK". Step 12. In the Add New Hardware Wizard window, click "Next".
Step 13. The Copying Files... window will appear. Step 14. In the Add New Hardware Wizard window, click "Finish". Then reboot the system.
6.3.3 Windows NT drivers Step 1. Click "Start" and select "Settings". Click "Control Panel" and double-click "Multimedia". Step 2. In the Multimedia Properties window, select the "Devices" tab. Then select the "Audio Devices" item, and click "Add...".
Step 3. In the Add window, select the "Unlisted..." item and click "OK". Step 4. When the Install Driver window appears, insert the utility disc into the CD-ROM drive. Type: D:\slotPC\6871\Audio\WinNT\ Then click "OK".
Step 5. In the Add Unlisted or Updated Driver window, select the "VIA PCI Audio controller" item. Then click "OK". Step 6. In the System Setting Change window, click "Restart Now".
6.3.4 Windows 2000 Drivers Step 1. Select “System”, “Setting”, “Control Panel” and double click “system” icon. Step 2. Choose “Multimedia Audio Controller” button.
Step 3. Choose “Driver button, press “Update Driver” button. Step 4.
Step 5. Click the “Have Disk...” button Step 6. Type the path D:\slotPC\6871\Audio\98se_Me_2k_xp\Win2000 press the “ok” button. Step 7.
Step 8. Press “Next” button Step 9.
PCI-6871 User’s Manual 92
CHAPTER 7 PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration.
Chapter 7 PCI Bus Ethernet Interface 7.1 Introduction The PCI-6871 is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible. The medium type can be configured via the RSET8139.exe program included on the utility disk. 7.2 Installation of Ethernet driver Before installing the Ethernet driver, note the procedures below.
7.2.2 Installation for Windows 98 Step 1. a. Select "Start", "Settings". "Control Panel". b. Double click "Network". Step 2. a. Click "Add" and prepare to install network functions.
Step 3. a. Select the "Adapter" item to add the Ethernet card. Step 4. a. Click "Have Disk" to install the driver. Step 5. a. Insert the CD into the D: drive b. Fill in "D:\slotPC\6871\LAN\” c.
Step 6. a. Choose the "Realtek RTL8139(A/B/C/8130) PCI Fast Ethernet" item. b. Click "OK". Step 7. a. Make sure the configurations of relative items are set correctly. b. Click "OK" to reboot.
7.2.3 Installation for Windows 2000 Step 1.
Step 2.
Step 3. Step 4.
Step 5. Step 6.
Step 7. Step 8.
Step 9. 7.2.4 Installation for Windows NT Step 1. a. Select "Start", "Settings", "Control Panel" b. Double click "Network" Step 2. a. Choose type of network.
b. Click "Next" Step 3. a. Click "Select from list...
Step 4. Click “Have Disk.” Step 5. a. Insert the Utility CD ROM b. Fill in the correct path: D:\slotPC\6871\LAN\8139C\winnt4 c. Click "OK".
Step 6. Check the highlighted item, and click “OK.
7. Click “Next” to continue setup. Step 8.
Step 9. Select the correct Network Services then click "Next" Step 10. Click “Next” to continue setup.
11. Click “Next” to start the network. 7.3 Further information Realtek website: www.realtek.com.tw Intel website: www.intel.com Manufacturer's website: www.emacinc.
PCI-6871 User’s Manual 110
Appendix A Programming the Watchdog Timer The PCI-6871 is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments. 111 Appx.
Appendix A Programming the Watchdog Timer A.1 Supported Input Timing Modes In order to program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a value of time interval. The value range is from 01 (hex) to 3E (hex), and the related time interval is 1 sec. to 62 sec. Data 01 02 03 04 3E Time Interval 1 sec. 2 sec. 3 sec. 4 sec. . . . 62 sec.
The following example shows how you might program the watchdog timer in BASIC: 10 20 30 40 50 60 70 80 1000 1070 2000 2090 REM Watchdog timer example program OUT &H443, data REM Start and restart the watchdog GOSUB 1000 REM Your application task #1 OUT &H443, data REM Reset the timer GOSUB 2000 REM Your application task #2 OUT &H443, data REM Reset the timer X=INP (&H443) REM Disable the watchdog timer END REM Subroutine #1, your application task . . . RETURN REM Subroutine #2, your application task . .
PCI-6871 Users’ Manual 114
Appendix B Installing PC/104 Modules This appendix gives instructions for installing PC/104 modules. 115 Appx.
Appendix B Installing PC/104 Modules B.1 Installing PC/104 Modules The PCI-6871's PC/104 connectors give you the flexibility to attach PC/ 104 modules. Installing these modules on the PCI-6871 is quick and simple. The following steps show how to mount the PC/104 modules: 1. Remove the PCI-6871 from your system, paying particular attention to the safety instructions already mentioned above. 2. Make any jumper or link changes required to the CPU card now.
PC/104 Mounting Support Male Female PCI-6871 Series PCA-6751 Series PC/104 module PC/104 module Figure B.1: PC/104 module mounting diagram 117 Appx.
Figure B.2: PC/104 module dimensions (mm) (±0.
Table B.
Table B.
Appendix C Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • • • • • • • • • • • • • • • • • • • • • • • CPU Fan Power Connector Ethernet 10/100Base-T Connector Audio Connector Main Power Connector Keyboard and PS/2 Mouse Connector Floppy Drive Connector IDE (1st and 2nd) HDD Connector Parallel Port Connector Power & HDD LED, Reset Button Connector USB Connector Backlight Connector IR Connector CRT Display Connector Flat Panel Connector Ext.
Appendix C Pin Assignments C.1 CPU Fan Power Connector (FAN 1) Table C.1: CPU Fan Power Connector (FAN 1) Pin Signal 1 2 3 Fan speed signal input Vcc GND C.2 Ethernet 10/100Base-T Connector (CN15) Table C.
C.3 Audio Connector (CN10) 15 13 3 1 16 14 4 2 Table C.3: Audio connector (CN10) Pin Signal Pin Signal 1 3 5 7 9 +5V DATA in GND DATA out +5V 2 4 6 8 10 BitCLK GND SYNC ACRST reserved 123 Appx.
C.4 Main Power Connector (CN11) Table C.
C.5 Keyboard and PS/2 Mouse Connector (CN25) Table C.5: Keyboard and mouse connector (CN25) Pin Signal 1 2 3 4 5 6 KB CLOCK KB DATA MS CLOCK GND +5V (KB VCC) MS DATA 125 Appx.
C.6 Floppy Disk Drive Connector (CN6) Table C.
C.7 IDE Hard Drive Connector (CN1, CN7) Table C.
C.8 Parallel Port Connector (CN2) Table C.
C.9 HDD, PWR LED CON & WDT output (CN13) Table C.9: HDD, PWR LED CON & WDT output (CN13) Pin Signal 1 2 3 4 5 6 WDT output GND power LED+ (+5V) HDD LED + power LED - (GND) HDD LED - C.10 Reset Button Connector (CN8) Table C.10: Reset Button Connector (CN8) Pin Signal 1 2 Reset signal input GND 129 Appx.
C.11 USB Connector (CN20, CN28) Table C.11: USB Connector (CN20, CN28) Pin Signal Pin Signal 1 3 5 7 9 +5 V UVUV+ GND Chassis GND 2 4 6 8 10 +5 V UVUV+ GND N/C C.12 LCD Inverter Backlight Connector (CN27) Table C.
C.13 IR Connector (CN9) Table C.13: IR Connector (CN9) Pin Signal 1 2 3 4 5 VCC (5 V) N.C. RX GND TX C.14 CRT Display Connector (CN12) 5 1 10 6 15 11 Table C.14: CRT Display Connector (CN12) Pin Signal Pin Signal 1 2 3 4 5 6 7 8 RED GREEN BLUE N/C GND GND GND GND 9 10 11 12 13 14 15 N/C GND N/C S-DATA H-SYNC V-SYNC S-CLK 131 Appx.
C.15 Flat Panel Connector (CN18) Table C.15: Flat Panel Connector (CN18) Pin Signal Pin Signal 1 3 5 VDDSAFE5 (+5v output) GND VDDSAFE3 (+3.3 v output) N/C P0 P2 P4 P6 P8 P10 P12 P14 P16 P18 P20 P22 GND SHFCLK M/DE N/C 2 4 6 VDDSAFE5 (+5v output) GND VDDSAFE3 (+3.3 v output) GND P1 P3 P5 P7 P9 P11 P13 P15 P17 P19 P21 P23 GND FLM LP ENAVEE 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Note: 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 The model number of the CN18 socket is DF13A-40DP-1.
C.16 Extended Flat Panel Display Connector (CN17) Table C.16: Extended Flat Panel Display Connector (CN17) Pin Signal Pin Signal 1 3 5 7 9 11 13 15 17 19 GND P24 P26 P28 P30 P32 P34 GND N/C N/C 2 4 6 8 10 12 14 16 18 20 GND P25 P27 P29 P31 P33 P35 GND N/C N/C Note: The model number of the CN17 socket is DF13A-20DP-1.25V (Hirose Electric Co., Ltd.) 133 Appx.
C.17 LCD Signal Mapping Table C.
C.18 LVDS Connector (CN21) Table C.18: LVDS Connector (CN21) Pin Signal Pin Signal 1 3 5 7 9 11 13 15 17 19 GND TX0+(Channel 1) TX0-(Channel 1) TX1+(Channel 1) TX1-(Channel 1) TX2+(Channel 1) TX2-(Channel 1) TX3+(Channel 1) TX3-(Channel 1) VDD (+3.3V) 2 4 6 8 10 12 14 16 18 20 GND TX0+(Channel 2) TX0-(Channel 2) TX1+(Channel 2) TX1-(Channel 2) TX2+(Channel 2) TX2-(Channel 2) TX3+(Channel 2) TX3-(Channel 2) VDD (+3.3V) 135 Appx.
C.19 COM Port Connector (CN19, CN20) Table C.
C.20 CompactFlash Card Connector (CN28) Table C.
C.21 ATX Power Feature Connector (CN3) Table C.21: ATX Power Feature Connector (CN3) Pin Signal 1 2 3 5VSB (Stand by voltage) GND PS. ON# C.22 LCD Backlight Connector (CN24) Table C.
C.23 External Keyboard Connector (CN26) Table C.23: External Keyboard Connector (CN26) Pin Signal 1 2 3 4 5 CLK DATA NC GND +5V 139 Appx.
PCI-6871 User’s Manual 140
Appendix D System Assignments This appendix contains information of a detailed nature. It includes: • • • • System I/O ports 1st MB memory map DMA channel assignments Interrupt assignments 141 Appx.
Appendix D System Assignments D.1 System I/O Ports Table D.1: System I/O ports Addr.
D.2 1st MB memory map Table D.2: 1st MB memory map Addr. range (Hex) Device F0000h - FFFFFh *CC000h - EFFFFh C0000h - CBFFFh B8000h - BFFFFh B0000h - B7FFFh A0000h - AFFFFh 00000h - 9FFFFh System ROM Unused (reserved for Ethernet ROM) Expansion ROM (for VGA BIOS) CGA/EGA/VGA text Unused EGA/VGA graphics Base memory * If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB) * E0000 - EFFFF is reserved for BIOS POST D.3 DMA channel assignments Table D.
D.4 Interrupt assignments Table D.
Appendix E Optional Extras for the PCI-6871 145 Appx.
E.1 Optional USB cable (CN20) Optional USB cable (2.0mm) part no.: 1703100260 E.2 ATX Power Control Cable part no.: 1703200100 E.3 Audio module Audio module with Line-in, Line out, mic PCI-6871 User’s Manual part no.
