Industrial Panel PCs Onyx-158/S Onyx-158/S 15” LCD PC with Expansion slot Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Copyright Notice This document is copyrighted, 2003. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Industrial Panel PCs Onyx-158/S Acknowledgments Intel and Pentium are registered trademarks of Intel® Corporation. IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc. UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc.
Industrial Panel PCs Onyx-158/S Packing List Before installing your Panel PC, please check if the package contains the following items. Onyx-158/S series Panel PC CD-ROM Contains User’s Manual, Drivers and Utilities Accessories - Screws bag - Jumper packbag - ISA Riser card If any of these items are missing or damaged, you should contact your distributor or sales representative immediately. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Industrial Panel PCs Onyx-158/S 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Industrial Panel PCs Onyx-158/S Contents Copyright Notice ..................................................................... 2 Acknowledgments ................................................................... 3 Packing List............................................................................... 4 Safety & Warranty.................................................................... 5 Charpter 1 General Information .................................................... 9 Introductions.............
Industrial Panel PCs Onyx-158/S Advanced Chipset Features .................................................. 40 Power management setup..................................................... 42 PC Health Status.................................................................... 44 Frequency/Voltage Control ................................................. 45 Load Fail-Safe Defaults......................................................... 46 Load Optimized Defaults.............................................
Industrial Panel PCs Onyx-158/S 1 Chapter General Information Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Introductions The Onyx-158/S is a compact, All-in-one network compatible PC with full safety approval and features to control a dedicated system with a wide variety of applications. Incorporation of the Onyx-158/S into your system can deliver both cost savings and efficiency improvements.
Industrial Panel PCs Onyx-158/S Features: 15” high brightness color TFT LCD display Aluminum alloy front panel All-in-one FC Socket 370 SBC (CPU supports up to Pentium® III 1GHz, FSB 66/100/133MHz) Removable anti-vibration 2.
Industrial Panel PCs Onyx-158/S Specifications: - Construction: Heavy-duty steel chassis and aluminum alloy front panel - Display: 15” XGA (1024 x 768) color TFT LCD - CPU: Support Socket 370 based Intel® Pentium® III and Celeron® CPU, up to 1GHz - Chipset: VIA VT8604 shared memory up to 32MB SDRAM - Memory: Support up to 512MB - Network (LAN): 10/100 Base-TX Ethernet port - Audio: VIA VT1611/1612, AC 97 2.
Industrial Panel PCs Onyx-158/S LCD Specifications Display type 15” color TFT LCD Max. Resolution 1024 x 768 Max. Colors 256K Dot size (mm) 0.33 x 0.33 Luminance (cd/m2) 250 (TYP) Viewing angle 160°(H) 160°(V) Operating temperature 0°~ 45℃ (32~113℉) Brightness Control Yes Back Light MTBF (Hrs) 50,000 Note: All AAEON's LCD products are manufactured with High precision technology. However, in all LCD panels there maybe a small number of defective pixels that do not change color.
Industrial Panel PCs Onyx-158/S Environmental Specification - Operating temperature: 0°to 45℃ (32~122℉) - Storage temperature: -20°to 60℃ (-4~140℉) - Storage humidity: 5 to 90%, non-condensing - Vibration: 10 to 150 Hz, 0.075mm peak to peak (operation) 10 cycles (sweep): 1 oct/min (endurance) - Shock: 15G peak acceleration (11 msec.
Industrial Panel PCs Onyx-158/S Dimensions Unit : m Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S 2 Chapter Hardware Installation Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S The panel PC is a PC-based industrial computer that is housed in aluminum alloy front panel and heavy-duty steel chassis. You can install 2.5”HDD easily by removing the side cover of HDD drive bay. Removing/Installing the HDD Unit 1. Screw the 2.5” HDD on four screws. 2. Cover the four screws with silica gel as diagram. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S 3. Unscrew the 7 attachment screws from the HDD drive bay. 1. Place 2.5” HDD into the drive bay and connect the IDE ribbon cable. 2. Replace the top cover of HDD drive bay and fix it with the 7 attachment screws. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S 6. Mount the drive bay into the machine by two screws. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Removing the rear maintenance cover 1. Remove the HDD module first then unscrew the two attachment screws from the top cover of the desktop stand. Caution: Handle the desktop stand with care, since it is made of aluminum and is weight 3kilogram. 2. Unscrew the four attachment screws then remove the foundation of stand. Onyx-158/S Series User Manual V1.
Industrial Panel PCs 3. Onyx-158/S Remove the stand holder by unscrewing the four attachment screws. 4. Unscrew the ten attachment screws used to hold the rear maintenance cover. 5. Remove the rear maintenance cover. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Mounting Installing Onyx-158/S is suitable for VESA75/100mm interface pads for arm mounting or desktop stand. Onys-158/S provides optional mounting kit for VESA75mm. Desktop Stand (optional mount kit: STAND-158D00) ARM mounting (ARM-LA0115 is for arm mounting) Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S 3 Chapter Jumper Settings Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Safety precautions Warning! Always completely disconnect the power cord from your chassis whenever you are working on it. Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the CPU card.
Industrial Panel PCs Onyx-158/S CPU Card - PCM-6898 Jumper Setting JP7 CN2 (AXT POWER) Board Layout JP8 CN15 J4 FAN1 CN4 J3 JP3 CN16 J1 J8 JP11 JP5 CN20 DIMM1 J9(IR) FDD1 CN18 CN1(FDD2) FAN2 CN19 Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Board Dimensions Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The following tables show the function of each of the board's jumpers. Jumpers Label Function J2 DOC Address Select (D800 default) J3/4 CD_IN (2.54mm)/CD_IN (2.
Industrial Panel PCs Onyx-158/S Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Industrial Panel PCs Onyx-158/S DOC Address Setting (J2) PIN Function 1-2, 3-4 3-4 OFF 1-2 Disabled DC00 D400 D800 * *Default Audio Port CD_IN (J3 & J4) J3-2.54mm J4-2.00mm PIN Function 1 2 3 4 CD-L GND GND CD_R For PCM-3730 (J5) PIN Function 1 2 3 4 5 5V_SB GND -RI SMBDT SMBCK Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S IrDA Connector (J9) PIN Function 1 2 3 4 5 6 +5V NC IRRX GND IRTX NC VIO Select (JP3) You can use JP3 to set the voltage input/output at 5 volts or 3.3 volts. PIN Function 2-3 1-2 3.3V 5V * *Default Wake On LAN (JP6) PIN Function 1-2 2-3 Enable Disable *Default Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S RS-232/422/485 COM2 (JP4,JP5) Setting PIN Function 1-2 3-4 5-6 RS-232 * RS-422 RS-485 PIN Function 1-2, 4-5, 7-8, 10-11 2-3, 5-6, 8-9, 11-12 2-3, 5-6, 8-9, 11-12 RS-232 * RS-422 RS-485 *Default Auto detect CPU Frequency (JP7/JP8) JP7 JP8 Function On On AUTO System Frequency (JP9 & JP10) JP9 JP10 Function On Off Off On On Off 66MHz 100MHz 133MHz or AUTO Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Clear CMOS (JP11) You can use JP11 to clear the CMOS data if necessary. To reset the CMOS data, place a jumper on JP11 (Clear CMOS) for just a few seconds, and then remove the jumper to the (Protect) position. PIN Function 2-3 1-2 Clear CMOS Protect * *Default Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S 4 Chapter BIOS Installation Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Industrial Panel PCs Onyx-158/S Award BIOS setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
Industrial Panel PCs Onyx-158/S Use this menu to change the values in the chipset registers and optimize your system’s performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.) PnP/PCI Configuration This entry appears if your system supports PnP/PCI.
Industrial Panel PCs Onyx-158/S Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Standard CMOS Features When you choose the Standard CMOS Features option from the INITIAL SETUP SCREEN menu, the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the right box of the Menu screen. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Advanced BIOS Features By choosing the Advanced BIOS Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Advanced Chipset Features By choosing the Advanced Chipset Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Integrated Peripherals By choosing the Integrated Peripherals from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Power management setup By choosing the Power Management Setup from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S PnP/PCI Configurations By choosing the PnP/PCI configurations from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S PC Health Status By choosing the PC Health Status from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Frequency/Voltage Control By choosing the Frequency/Voltage Control from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898. Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S Load Fail-Safe Defaults When you press on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Default (Y/N)? Pressing "Y" loads the BIOS default values for the most stable, minimal performance system operations.
Industrial Panel PCs Setup Onyx-158/S Enter a password whenever you enter Setup. NOTE: To clear the password, simply press Enter when asked to enter a password. Then the password function is disabled. Save & Exit setup If you select this option and press , the values entered in the setup utilities will be recorded in the chipset’s CMOS memory. The microprocessor will check this every time you turn on your system and compare this to what it finds as it checks the system.
Industrial Panel PCs Onyx-158/S 5 Chapter Drivers Installation Onyx-158/S Series User Manual V1.
Industrial Panel PCs Onyx-158/S The Onyx-158/S comes with a CD, which contains most of drives and utilities of your needs. There are several ways of installation depending on the driver package under different Operating System application. If you utilize Windows NT series OS, you are strongly recommended to download the latest version Windows NT Service Pack from Microsoft website and install it before installing any driver.
Industrial Panel PCs Onyx-158/S the following path: “cd-rom”: \Driver\ CPU Board\ PCM-6898\ Step 3 – Install Ethernet Driver” “cd-rom”: \Driver\ CPU Board\ PCM-6898\ Step 4 – Install Audio Driver” Press the key or click OK to begin the installation. (Remarks: "cd-rom" means your CD-ROM drive letter) 3. The setup will automatically detect your OS and complete the installation. Simply following the step-by-step instruction. 4. Shut down and restart your system. Onyx-158/S Series User Manual V1.
