® ThinkPad R61, R61e, and R61i (15.
® ThinkPad R61, R61e, and R61i (15.
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 233. Sixth Edition (June 2008) © Copyright Lenovo 2007, 2008. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Common service tools . . . . . . . . . 231 Trademarks . . . Notices . . . . . . . . . . . . . . 233 iv ThinkPad R61, R61e, and R61i (15.4-inch widescreen) Hardware Maintenance Manual . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad R61 and R61i MT 7642, 7643, 7644, 7645, 7646, 7647, 7648, 8914, 8918, 8919, 8920, 8927, 8928, 8929, 8930, 8932, 8933, 8934, 8935, 8936, and 8937 ThinkPad R61e and R61i MT 7649, 7650, and 7657 Use this manual along with the advanced diagnostic tests to troubleshoot problems.
vi ThinkPad R61, R61e, and R61i (15.
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad R61, R61e, and R61i (15.
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
warranty.vm&sitestyle=lenovo Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad R61, R61e, and R61i (15.
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 28 – “PC-Doctor for Rescue and Recovery” on page 28 v “Power system checkout” on page 29 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “R61, R61e, and R61i (15.4-inch widescreen)” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
On the first screen, select the model and press Enter. Follow the instructions on the screen. 2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it. 6. To exit the test, select Quit — Exit Diag. To cancel the test, press Esc. Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 64). 4. Remove the backup battery (see “1100 Backup battery” on page 79). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
32 ThinkPad R61, R61e, and R61i (15.
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 64. 3. Remove the backup battery. For how to remove the backup battery, see “1100 Backup battery” on page 79. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5.
3. 4. 5. 6. 7. 8. 9. 36 Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. Select Security, using the cursor directional keys to move down the menu. Select Password. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. Select Master HDP.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage® button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems” on page 46 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 40 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important:The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
R61, R61e, and R61i (15.4-inch widescreen) This chapter presents following product-specific service references and product-specific parts information.
Specifications The following table lists the specifications of the ThinkPadR61, R61e, and R61i (15.4-inch widescreen) : Table 7. Specifications Feature Description Processor v Intel® Core™ 2 Duo processor T5250 (1.5 GHz), 2-MB L2 cache v Intel Core 2 Duo processor T5270 (1.4 GHz), 2-MB L2 cache v Intel Core 2 Duo processor T5450 (1.66 GHz), 2-MB L2 cache v Intel Core 2 Duo processor T5470 (1.6 GHz), 2-MB L2 cache v Intel Core 2 Duo processor T5550 (1.
Table 7. Specifications (continued) Feature Description Processor (continued) v Intel® Celeron® M processor T530 (1.73 GHz), 1-MB L2 cache v Intel Celeron M processor 540 (1.86 GHz), 1-MB L2 cache v Intel Celeron M processor 550 (2.0 GHz), 1-MB L2 cache v Intel Celeron M processor 560 (2.13 GHz), 1-MB L2 cache v Intel Celeron M processor 570 (2.26 GHz), 1-MB L2 cache v Intel Celeron Dual Core processor T1400 (1.73 GHz), 512-KB L2 cache v Intel Celeron Dual Core processor T1500 (1.
Table 7. Specifications (continued) Feature Description I/O port v v v v v v v v Internal modem v 56.
Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 6 7 8 9 10 9 8 7 R61, R61e, and R61i (15.
Table 8. Status indicators Indicator Meaning 1 Wireless status Green: The wireless feature (the IEEE 802.11 standard or IEEE 802.11n) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Bluetooth status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R 52 3 Num lock Green: The numeric keypad on the keyboard is enabled.
Table 8. Status indicators (continued) Indicator 10 Meaning Ultrabay Green: An Ultrabay Enhanced device is installed and in use. Enhanced status Blinking green: An Ultrabay Enhanced device is in the process of being detached. Turn off: An Ultrabay Enhanced device is ready to be attached or detached. Note: If you are using Windows 2000, the Ultrabay Enhanced status indicator does not blink while an Ultrabay Enhanced device is being detached.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad Advanced Dock, the ThinkPad Advanced Mini Dock or the ThinkPad Essential Port Replicator is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
Table 9. FRU tests (continued) FRU Applicable test Diskette drive 1. Diagnostics --> Diskette Drives 2. Interactive Tests --> Diskette DVD drive or DVD/CD-RW combo drive 1. Diagnostics --> Other Devices --> Optical Drive 2. Interactive Tests --> Optical Drive Test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Memory Test—Quick. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. 3.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Note: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Note: 1.
Table 10. Fn key combinations (continued) Key combination Description 58 Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Has the same function as the SysRq key. Fn+ScrLk Enable or disable the numeric keypad. Fn+Pause Has the same function as the Break key. Fn+cursor keys These key combinations work with Windows Media Player.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 62 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten. R61, R61e, and R61i (15.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 59. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 11. Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . 1 2 3 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1020 Ultrabay Enhanced device for R61 and R61i Note: Ultrabay Enhanced does not accept any of the following devices: v Ultrabay PlusTM devices v Ultrabay 2000TM devices v Ultrabay Slim devices Table 12. Removal steps of Ultrabay Enhanced device for R61 and R61i When you release the switch in step 1 , the lever pops out. In step 2 , pull the lever a little to release the device from the bay. 1 2 3 R61, R61e, and R61i (15.
1030 Hard disk drive cover, hard disk drive, and hard disk rubber rails For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 13. Removal steps of hard disk drive cover, hard disk drive, and hard disk rubber rails (continued) 4 5 3 When installing: Make sure that the hard disk drive connector is attached firmly. 6 6 When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. R61, R61e, and R61i (15.
1040 Palm rest or palm rest with fingerprint reader For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 14.
Table 14. Removal steps of palm rest (continued) 2 2 3 When installing: When you attach the palm rest, do as follows: 1. Attach the fingerprint reader connector firmly to the system board. R61, R61e, and R61i (15.
Table 14. Removal steps of palm rest (continued) 2. Attach the palm rest so that the two projections of the palm rest ( a ) firmly fit into the guide holes of the keyboard bezel as shown in this figure. a a 3. Push the front side of the palm rest until it clicks into place. 4. Close the LCD cover and turn the computer over. Then fasten the four screws to secure the palm rest. 70 ThinkPad R61, R61e, and R61i (15.
1050 DIMM For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 Table 15. Removal steps of dimm Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). 1 b 2 a 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1060 Keyboard For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 Table 16. Removal steps of keyboard 1 Step 1 Icon Screw (quantity) Color Torque M2 × 17 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) Lift the keyboard a little in the direction shown by arrow 2 , and then detach the connector 3 . 2 3 72 ThinkPad R61, R61e, and R61i (15.
Table 16. Removal steps of keyboard (continued) When installing: Make sure that the keyboard edges a are under the frame as shown in this figure. a a R61, R61e, and R61i (15.
1070 Optical drive for R61e and R61i For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 Table 17. Removal steps of optical drive 1 Step Screw (quantity) Color Torque 1 M3 × 4 mm, flat-head, nylon-coated (1) Black 0.392 Nm (4 kgfcm) 2 3 Push the optical drive by using a screwdriver 2 as shown in this figure. Then pull out the optical drive 3 .
1080 Modem daughter card (MDC-1.5) For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 Table 18. Removal steps of modem daughter card (MDC-1.5) Note: Some models do not have the modem daughter card because the modem function is on the system board. 1 2 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm (1.
Table 18. Removal steps of modem daughter card (MDC-1.5) (continued) Turn the card over 3 , and detach the modem connector 4 . 3 4 When installing: Make sure that the modem connector and the connector on the underside of the card are attached firmly. 76 ThinkPad R61, R61e, and R61i (15.
1090 PCI Express Mini Card for wireless LAN For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 Table 19. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 19. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: In models with 802.11 a/b/g wireless LAN card, plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX. If the computer you are servicing has three cables and the 802.11 a/b/g wireless LAN card, put the white cable in the cable bag in the card slot. In models with 802.
1100 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 Table 20. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly. R61, R61e, and R61i (15.
1110 Keyboard bezel and speakers For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 Table 21. Removal steps of keyboard bezel and speakers Note: Speakers are attached to the underside of the keyboard bezel. 1 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (3) Silver 0.167 Nm (1.
Table 21. Removal steps of keyboard bezel and speakers (continued) 4 4 4 3 4 4 4 In step 3 , release the wireless antenna cables from the cable guide. Step Screw (quantity) Color Torque 4 M2 × 3 mm, flat-head, nylon-coated (6) Silver 0.167 Nm (1.7 kgfcm) In step 5 , strip the securing tapes off. Then detach the speaker connector 6 . 5 5 5 5 5 6 When installing: Make sure that speaker connector is attached firmly. R61, R61e, and R61i (15.
Table 21. Removal steps of keyboard bezel and speakers (continued) In step 7 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 8 . 7 7 8 7 7 8 When installing: Make sure that all the claws are attached firmly. 9 10 9 9 10 9 82 Step Screw (quantity) Color Torque 9 M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.167 Nm (1.7 kgfcm) ThinkPad R61, R61e, and R61i (15.
1120 Fan assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1110 Keyboard bezel and speakers” on page 80 Table 22. Removal steps of fan assembly 2 3 2 1 3 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) 2 M2 × 9.5 mm, pan-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) R61, R61e, and R61i (15.
Table 22. Removal steps of fan assembly (continued) Attention: Do not handle the fan roughly. Improper handling of the fan can cause distortion or deformation and imperfect contact with components. 5 4 4 Step Screw (quantity) Color Torque 4 M2 × 9.5 mm, pan-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 5 , release the wireless antenna cables from the cable guide of the fan assembly. 7 6 84 ThinkPad R61, R61e, and R61i (15.
Table 22. Removal steps of fan assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. a v Make sure that the fan connector is attached firmly.
1130 CPU For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1110 Keyboard bezel and speakers” on page 80 v “1120 Fan assembly” on page 83 Table 23. Removal steps of CPU Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU.
1140 LCD assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1090 PCI Express Mini Card for wireless LAN” on page 77 v “1110 Keyboard bezel and speakers” on page 80 Table 24. Removal steps of LCD assembly 1 1 Step Screw (quantity) Color Torque 1 M2 × 9.5 mm, pan-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) R61, R61e, and R61i (15.
Table 24. Removal steps of LCD assembly (continued) 4 4 3 2 3 Step Screw (quantity) Color Torque 3 M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 4 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame. 88 ThinkPad R61, R61e, and R61i (15.
Table 24. Removal steps of LCD assembly (continued) 5 5 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly. R61, R61e, and R61i (15.
1150 Base cover, USB sub card with cable, and PC Card/ExpressCard (or PC Card/Smart Card) bezel assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1090 PCI Express Mini Card for wireless LAN” on page 77 v “1110 Keyboard bezel and speakers” on page 80 v “1140 LCD assembly” on page 87 Table 25.
Table 25. Removal steps of base cover, USB sub card with cable, and PC Card/ExpressCard (or PC Card/Smart Card) bezel assembly (continued) 3 3 4 4 Step Screw (quantity) Color Torque 3 M2 × 9.5 mm, pan-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 4 M2 × 17 mm, pan-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 6 5 5 Step Screw (quantity) Color Torque 5 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.167 Nm(1.7 kgfcm) R61, R61e, and R61i (15.
Table 25. Removal steps of base cover, USB sub card with cable, and PC Card/ExpressCard (or PC Card/Smart Card) bezel assembly (continued) Attention: Before step 7 , be sure that the Ultrabay Enhanced device eject lever has not popped out. It must be housed in its position as shown in the figure a . 7 8 a 92 ThinkPad R61, R61e, and R61i (15.
Table 25. Removal steps of base cover, USB sub card with cable, and PC Card/ExpressCard (or PC Card/Smart Card) bezel assembly (continued) Remove the USB sub card with cable and the security hole bracket as in this figure. 1 1 4 2 3 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm(1.7 kgfcm) 3 M2 × 3.5 mm, flat-head, nylon-coated (1) Black 0.167 Nm(1.7 kgfcm) When attaching the PC Card/ExpressCard bezel assembly, do as shown in this figure.
Table 25. Removal steps of base cover, USB sub card with cable, and PC Card/ExpressCard (or PC Card/Smart Card) bezel assembly (continued) When attaching the PC Card/Smart Card bezel assembly, do as shown in this figure. 1 2 94 ThinkPad R61, R61e, and R61i (15.
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 1 Product label 2 Homologation label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1160 Structure frame and IEEE 1394 sub card For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1020 Ultrabay Enhanced device for R61 and R61i” on page 65 v “1030 Hard disk drive cover, hard disk drive, and hard disk rubber rails” on page 66 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1070 Optical drive for R61e and R61i” on page 74 v “1080 Modem daughter card (MDC-1.
Table 26. Removal steps of structure frame and IEEE 1394 sub card (continued) Remove the ac power jack cable a and the modem cable b . 3 a b 5 4 2 4 When installing: Make sure the connectors are attached firmly, and that the cables are routed as in the figure above. R61, R61e, and R61i (15.
Table 26. Removal steps of structure frame and IEEE 1394 sub card (continued) Remove the CPU support plate. 6 98 Step Screw (quantity) Color Torque 6 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) ThinkPad R61, R61e, and R61i (15.
Table 26. Removal steps of structure frame and IEEE 1394 sub card (continued) 7 7 8 7 7 7 a Step Screw (quantity) Color Torque 7 M2 × 3.5 mm, flat-head, nylon-coated (8) Black 0.167 Nm (1.7 kgfcm) 8 M2 × 9.5 mm, pan-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: When attaching the system board to the frame, adjust the placement with the small projection a . Then secure the system board with the screws. R61, R61e, and R61i (15.
Table 26. Removal steps of structure frame and IEEE 1394 sub card (continued) In step 10 , remove the system board and the PC Card/ExpressCard (or PC Card/Smart Card) slots assembly from the structure frame together. In step 11 and 12 , remove IEEE 1394 sub card. 10 9 11 12 100 Step Screw (quantity) Color Torque 11 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) ThinkPad R61, R61e, and R61i (15.
1170 System board, PC Card/ExpressCard (or PC Card/Smart Card) slots assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v At every point in the process, be sure not to drop or stack the system board. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces.
Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. a Accelerometer chip for the HDD Active Protection SystemTM b Security chip c CPU d Video chip e MCH (Memory Controller Hub) f ICH (I/O Controller Hub) c d f e b a Table 27. Removal steps system board, PC Card/ExpressCard (or PC Card/Smart Card) slots assembly 1 1 102 Step Screw (quantity) Color Torque 1 M2 × 2.
Table 27. Removal steps system board, PC Card/ExpressCard (or PC Card/Smart Card) slots assembly (continued) Turn the system board over, and then disconnect the PC Card/ExpressCard slots assembly a from the system board. a 2 When installing: Make sure that the connector of the PC Card/Express Card slot assembly is attached to the system board firmly. R61, R61e, and R61i (15.
2010 LCD front bezel For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 Table 28. Removal steps of LCD front bezel 1 2 1 2 2 Step Screw cap Screw (quantity) Color Torque 1 M2.5 × 6.5 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) 2 M2.5 × 6.5 mm, wafer-head, nylon-coated (3) Black 0.392 Nm (4 kgfcm) 4 5 3 3 3 3 3 3 3 104 3 ThinkPad R61, R61e, and R61i (15.
2020 Inverter card For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “2010 LCD front bezel” on page 104 Table 29. Removal steps of inverter card 2 1 4 3 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connectors 3 and 4 are attached firmly. R61, R61e, and R61i (15.
2030 Bluetooth daughter card (BDC-2) For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “2010 LCD front bezel” on page 104 Table 30. Removal steps of Bluetooth daughter card 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connector is attached firmly. 106 ThinkPad R61, R61e, and R61i (15.
2040 LCD panel, LCD cable, and hinges For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1090 PCI Express Mini Card for wireless LAN” on page 77 v “1110 Keyboard bezel and speakers” on page 80 v “1140 LCD assembly” on page 87 v “2010 LCD front bezel” on page 104 Table 31. Removal steps of LCD panel, LCD cable, and hinges 4 1 1 3 2 1 Step Screw (quantity) Color Torque 1 M2.
Table 31. Removal steps of LCD panel, LCD cable, and hinges (continued) Remove the hinges a . a 6 5 5 a 5 6 5 Step Screw (quantity) Color Torque 5 M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.167 Nm (1.7 kgfcm) Remove the LCD cable b . 7 b 8 When installing: Make sure that the connector is attached firmly. 108 ThinkPad R61, R61e, and R61i (15.
Table 31. Removal steps of LCD panel, LCD cable, and hinges (continued) Cable routing: When you install the LCD panel, make sure that the antenna cables are routed as shown in this figure. R61, R61e, and R61i (15.
2050 LCD rear cover, wireless LAN antenna cables, and integrated camera For access, remove these FRUs, in order: v “1010 Battery pack” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 68 v “1060 Keyboard” on page 72 v “1090 PCI Express Mini Card for wireless LAN” on page 77 v “1110 Keyboard bezel and speakers” on page 80 v “1140 LCD assembly” on page 87 v “2010 LCD front bezel” on page 104 v “2020 Inverter card” on page 105 v “2030 Bluetooth daughter card (BDC-2)” on page 106 v “20
Table 32. Removal steps of LCD rear cover, wireless LAN antenna cables, and integrated camera (continued) 2 2 R61, R61e, and R61i (15.
Table 32. Removal steps of LCD rear cover, wireless LAN antenna cables, and integrated camera (continued) Remove the integrated camera as shown in this figure. Note: The part marked a is fragile and might be damaged by rough handling. When you remove the camera, do not hold that part to avoid the damage. 1 a 112 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.167 Nm(1.7 kgfcm) ThinkPad R61, R61e, and R61i (15.
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ThinkLight Integrated camera (for some models) Status indicatorsNote: For the description of each indicator, see “Status indicators” on page 51.
Rear view 1 2 3 4 5 6 7 8 9 10 11 12 Status indicators Note: For the description of each indicator, see “Status indicators” on page 51.
Bottom view 1 2 3 4 5 6 7 8 Battery pack Battery pack latch Docking connector Wireless radio switch 4-in-1 Media Card reader 4-in-1 Media Card reader eject button LCD cover latch Hard disk drive 1 2 3 8 7 6 5 4 R61, R61e, and R61i (15.
Parts list This section contains following lists of the service parts. v “Overall” on page 117 v “LCD FRUs” on page 188 v “Keyboard” on page 205 v “Miscellaneous parts” on page 206 v “AC adapters” on page 209 v “Power cords” on page 210 v “Recovery discs” on page 211 v “Common service tools” on page 231 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 24 2 23 3 f a 4 e 22 b 21 5 20 6 19 18 7 8 17 9 10 d 11 16 12 c 15 13 14 R61, R61e, and R61i (15.
Table 33. Parts list—Overall 118 No. FRU a-f See “Miscellaneous parts” on page 206. FRU no. RoHS ID CRU ID 42X3943 R N R ** 1 LCD unit (see “LCD FRUs” on page 188.
Table 33. Parts list—Overall (continued) No. 3 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 3 120 FRU FRU no. RoHS ID CRU ID Palm rest assembly with fingerprint reader, with IBM logo v 7642-CTO v 7643-CTO v 7644-CTO v 7645-CTO v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO v 8918-CTO v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO 42W3902 R ** ThinkPad R61, R61e, and R61i (15.
Table 33. Parts list—Overall (continued) No. 3 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 3 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No.
Table 33. Parts list—Overall (continued) No. 4 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 4 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 128 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 132 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 6 FRU FRU no.
Table 33. Parts list—Overall (continued) No.
Table 33. Parts list—Overall (continued) No. 7 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 7 136 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No. 10 138 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 60 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 80 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 FRU FRU no. RoHS ID CRU ID (continued) SATA hard disk drive, 80 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 120 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 142 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 160 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 10 FRU FRU no. RoHS ID CRU ID Seagate OP 42T1311 R * HGST 42T1473 R * HGST OP 42T1471 R * Fujitsu OP 42T1481 R * SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm (FDE) v 8914-CTO v 8918-CTO v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, E8x, E9x v 7657-CTO SATA hard disk drive, 250 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 10 144 FRU FRU no. RoHS ID CRU ID HGST OP 42T1483 R * Seagate 39T2795 R * HGST OP 42T1485 R * Seagate 39T2799 R * SATA hard disk drive, 60 GB, 9.
Table 33. Parts list—Overall (continued) No. 10 10 FRU FRU no. RoHS ID CRU ID HGST OP 42T1461 R * Seagate 42T1439 R * Fujitsu 42T1465 R * 42T1463 R * SATA hard disk drive, 160 GB, 9.5 mm, 7,200 rpm v 8914-CTO v 8918-CTO v 8919-CTO, AVx, DLx v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO SATA hard disk drive, 200 GB , 9.
Table 33. Parts list—Overall (continued) No. 11 FRU FRU no. RoHS ID CRU ID Battery pack, Li-ion (6 cell, 2.
Table 33. Parts list—Overall (continued) No. 11 FRU FRU no. RoHS ID CRU ID Sanyo 42T4513 R * Panasonic 42T5233 R * Sanyo 42T4504 R * Panasonic 92P1139 R * Sony 92P1141 R * (continued) Battery pack, Li-ion (6 cell, 2.4 Ah) v 8930-all v 8932-all v 8933-all v 8934-all v 8935-all v 8936-CTO, 22x v 8937-CTO, 22x v 7649-all v 7650-all v 7657-all 11 Battery pack, Li-ion (6 cell, 2.
Table 33. Parts list—Overall (continued) No. 11 12 148 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 12 13 13 FRU FRU no. RoHS ID CRU ID Foxconn 42W7829 R N Iida 42W7828 R N PCC (UJDA780DVD) 39T2817 R * HLDS (GDR-T10N) 39T2665 R * USB sub card v 7649-all v 7650-all v 7657-all DVD drive, 12.
Table 33. Parts list—Overall (continued) No. 13 13 150 FRU FRU no. RoHS ID CRU ID DVD/CD-RW combo drive, 12.
Table 33. Parts list—Overall (continued) No. 13 FRU FRU no. RoHS ID CRU ID DVD-RAM/RW drive, 12.
Table 33. Parts list—Overall (continued) No. 13 13 FRU FRU no. RoHS ID CRU ID DVD-RAM/RW drive, 12.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 13 Blu-Ray disk drive, 12.7 mm v 7642-CTO v 7643-CTO v 7644-CTO v 7645-CTO v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO v 8918-CTO, 5Hx, 5Jx, ATx v 8919-CTO, 6Wx, 6Zx, 72x, 73x, AVx, DLx v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8832-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO 39T2853 R * 13 Travel cover, 12.
Table 33. Parts list—Overall (continued) No. 15 15 15 15 15 15 15 154 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 15 15 15 15 15 15 15 FRU FRU no.
Table 33. Parts list—Overall (continued) No.
Table 33. Parts list—Overall (continued) No. 16 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 16 158 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 17 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 17 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 17 FRU FRU no.
Table 33. Parts list—Overall (continued) No. 17 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No. 164 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No. 166 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T5270 (1.4 GHz) v 8914-CTO v 8918-CTO, APx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO, FZx, G2x, G3x, G4x v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO, EAx, EBx, ECx 42W7856 R N 19 CPU assembly, Intel Core 2 Duo processor T5450 (1.
Table 33. Parts list—Overall (continued) No. 168 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T5470 (1.6 GHz) v 8914-CTO v 8918-CTO, ADx, AEx, AFx, AGx, AHx, AJx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, E7x, FYx v 8933-CTO, G5x v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, 8Kx v 7657-CTO, EDx 42W7840 R N 19 CPU assembly, Intel Core 2 Duo processor T5550 (1.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T5670 (1.8 GHz) v 8914-CTO v 8918-CTO v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO 43N7741 R N 19 CPU assembly, Intel Core 2 Duo processor T5750 (2.
Table 33. Parts list—Overall (continued) No. 170 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T5850 (2.16 GHz) v 8914-CTO v 8918-CTO, DQx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO 43N7740 R N 19 CPU assembly, Intel Core 2 Duo processor T5870 (2.
Table 33. Parts list—Overall (continued) No. 19 FRU FRU no. CPU assembly, Intel Core 2 Duo processor T7100 (1.
Table 33. Parts list—Overall (continued) No. 19 FRU FRU no. RoHS ID CRU ID (continued) 42W7654 R N 42W7847 R N CPU assembly, Intel Core 2 Duo processor T7100 (1.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T7300 (2.
Table 33. Parts list—Overall (continued) No. 19 174 FRU FRU no. RoHS ID CRU ID CPU assembly, Intel Core 2 Duo processor T7500 (2.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T8100 (2.
Table 33. Parts list—Overall (continued) No. 176 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T8300 (2.4 GHz) v 8914-CTO, CSx, CWx v 8918-CTO v 8919-CTO, D5x, DGx, DJx, DKx v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO, EEx, FMx v 8932-CTO v 8933-CTO, ETx, EVx, EWx, EYx, FPx, FQx, FSx v 8934-CTO, FAx v 8935-CTO, FBx v 8936-CTO v 8937-CTO v 7649-CTO, CTx, DBx, DCx v 7650-CTO v 7657-CTO, CXx 42W7880 R N 19 CPU assembly, Intel Core 2 Duo processor T8300 (2.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T9300 (2.5 GHz) v 8914-CTO, CUx v 8918-CTO v 8919-CTO, D6x, DLx v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO, B0x, EZx, FTx v 8934-CTO v 8935-CTO, FCx v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO 42W7879 R N 19 CPU assembly, Intel Core 2 Duo processor T9300 (2.
Table 33. Parts list—Overall (continued) No. 178 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T9500 (2.6 GHz) v 8914-CTO v 8918-CTO, 60x v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO, A0x v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, B0x v 7657-CTO 42W7878 R N 19 CPU assembly, Intel Core 2 Duo processor T9500 (2.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Pentium Dual Core processor T2310 43N7304 (1.46 GHz) v 8914-CTO v 8918-CTO, AQx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, ARx, ATx, AWx, B2x, D5x, D7x v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, 9Nx, 9Px, 9Qx, 9Rx, 9Yx, 9Zx, A6x, A7x, C9x v 7657-CTO R N 19 CPU assembly, Intel Pentium Dual Core processor T2330 43N7303 (1.
Table 33. Parts list—Overall (continued) No. 180 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Pentium Dual Core processor T2370 42W7865 (1.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Pentium Dual Core processor T2410 42W8046 (2.0 GHz) v 8914-CTO v 8918-CTO v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, GTx, GUx, GVx, GWx, GXx, GYx v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, EGx, EMx, ESx, EVx, EYx, EZx, F2x, F3x, F4x, F5x v 7657-CTO R N 19 CPU assembly, Intel Celeron M processor 530 (1.
Table 33. Parts list—Overall (continued) No. 182 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Celeron M processor 550 (2.0 GHz) v 8930-CTO v 8932-CTO v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO, DKx, DMx v 7650-CTO, DPx, DQx, EEx, EFx, EJx, EKx v 7657-CTO 41W7841 R N 19 CPU assembly, Intel Celeron M processor 560 (2.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 20 CPU assembly, Intel Celeron Dual Core processor T1500 (1.
Table 33. Parts list—Overall (continued) No. 20 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no.
Table 33. Parts list—Overall (continued) No. 21 21 186 FRU FRU no.
Table 33. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 23 Keyboard (see “Keyboard” on page 205.) 24 TrackPoint stick caps 91P9642 R * — Thermal grease 91P8835 R N — Telephone cable, RoHS 91P6915 R * — AC adapter (see “AC adapters” on page 209.) R61, R61e, and R61i (15.
LCD FRUs In R61, R61e, and R61i (15.4-inch widescreen), there are following types of LCDs. v “15.4-in. WXGA TFT” on page 189 v “15.4-in. WSXGA+ TFT” on page 199 10 9 8 7 6 5 4 3 2 188 ThinkPad R61, R61e, and R61i (15.
15.4-in. WXGA TFT Table 34. Parts list—15.4-in. WXGA TFT No. FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 4 190 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 4 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 4 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 194 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 8 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 8 FRU FRU no.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 9 FRU FRU no. RoHS ID CRU ID LCD panel, 15.4-in.
Table 34. Parts list—15.4-in. WXGA TFT (continued) No. 9 FRU FRU no. RoHS ID CRU ID (continued) LCD panel, 15.4-in.
15.4-in. WSXGA+ TFT Table 35. Parts list—15.4-in. WSXGA+ TFT No. FRU FRU no.
Table 35. Parts list—15.4-in. WSXGA+ TFT (continued) No. 200 FRU FRU no.
Table 35. Parts list—15.4-in. WSXGA+ TFT (continued) No. FRU FRU no.
Table 35. Parts list—15.4-in. WSXGA+ TFT (continued) No. FRU no.
Table 35. Parts list—15.4-in. WSXGA+ TFT (continued) No. 8 FRU FRU no.
Table 35. Parts list—15.4-in. WSXGA+ TFT (continued) No. 9 10 204 FRU FRU no. RoHS ID CRU ID LCD panel, 15.4-in.
Keyboard Language P/N (ALPS) P/N P/N (Chicony) (NMB) RoHS ID CRU ID Arabic 42T3212 42T3276 42T3146 R ** Belgian 42T3213 42T3277 42T3147 Brazilian Portuguese 42T3240 42T3304 42T3174 Canadian French (058) 42T3211 42T3275 42T3145 Canadian French (Acnor) 42T3210 42T3274 42T3144 Czech 42T3214 42T3278 42T3148 Danish 42T3215 42T3279 42T3149 Dutch 42T3223 42T3287 42T3157 Finnish, Swedish 42T3230 42T3294 42T3164 French 42T3217 42T3281 42T3151 German 42T3218 42T3282 4
Miscellaneous parts Table 36. Parts list—Miscellaneous parts 206 FRU P/N RoHS ID CRU ID Screw kit (including nylon-coated screws): v M2 × 2.7 mm (black), flat head (2) v M2 × 2.8 mm (silver), flat head (10) v M2 × 3 mm (silver), flat head (25) v M2 × 3.5 mm (black), flat head (15) v M2 × 5mm (black), flat head (15) v M2 × 9.5 mm (black), pan head (15) v M2 × 17mm (black), pan head (15) v M2.5 × 4mm (black), flat head (5) v M2.5 × 6.5 mm (black), wafer head (10) v M3 × 2.
Table 36.
Table 36. Parts list—Miscellaneous parts (continued) FRU P/N RoHS ID CRU ID System miscellaneous parts for R61 and R61i: v (a) DC in cable v (b) Modem cable assembly, MDC-1.5 v (c)Bracket, Kensington v (d) Bracket, CPU support v (e) Bracket, N/B, fan discrete/integ. v (f) Bracket, VGA, fan discrete/integ. v RJ11 cable assembly 42X3946 R N 42X4485 R N 42X4486 R N Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 117.
Table 36. Parts list—Miscellaneous parts (continued) FRU P/N RoHS ID CRU ID System board miscellaneous parts: v Insulation sheet, docking v Insulation sheet, front louver v Insulation sheet, PC Card slot v Insulation sheet, front top v Insulation sheet, bottom CPU v Shield sheet for DC v Insulation sheet, NB v Insulation sheet, Video 42X3944 R N P/N RoHS ID CRU ID AC adapters Table 37.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 38. Parts list—2-pin power cords Region P/N P/N (Longwell) (Volex) RoHS ID CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 R * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -Exx, Jxx 42T5014 42T5099 Table 39.
Recovery discs Windows XP Professional CDs for R61, R61e, and R61i (some models) Windows XP Professional is preinstalled as the operating system in the following models: v 7642-CTO v 7643-CTO v 7644-CTO v 7645-CTO v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO, 3Wx, 3Xx, 3Yx v 8918-CTO, 5Ux, 5Vx,, 5Wx, 5Xx, B9x, BAx, CXx, DFx v 8919-CTO, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx, 7Px, 7Qx, AXx, AZx, DGx v 8920-CTO v 8927-CTO, 9Sx, 9Tx, 9Ux, 9Vx, 9Wx v 8928-CTO v 8929-CTO v 8930-CTO, 3Sx, 3Tx, 9Px, 9Qx, 9Rx, A9x, EBx, EHx v
Table 40.
Windows XP Professional CDs for R61i (some models) Windows XP Professional is preinstalled as the operating system in the following models: v 8914-CTO v 8918-CTO, DMx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, DZx, E2x, E6x, E9x, FDx, FHx, FWx, FXx, GKx, GNx, GZx, H2x v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, CDx, D5x, D6x, DGx, DHx, E8x, ELx, F6x v 7657-CTO R61, R61e, and R61i (15.
Table 41.
Windows Vista Home Basic (32 bit) DVDs for R61, R61e, and R61i (some models) Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 7642-CTO, 23x, 24x, 2Bx v 7643-CTO, 3Fx, 3Gx v 7644-CTO, 47x, 4Kx, 7Jx v 7645-CTO, 5Ax v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Px, 3Ux, A2x, A3x, A4x, A5x, CRx, CSx v 8918-CTO, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx v 8919-CTO, 6Lx, 6Mx, 6Nx, 6Px, 6Qx, AUx v 8920-CTO, 8Jx, 8Kx, 8Lx, 8Mx, 8Nx,
Table 42.
Windows Vista Home Basic (32 bit) DVDs for R61i (some models) Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 8914-CTO v 8918-CTO, ADx, AEx, AFx, AGx, AHx, AJx, AKx, ALx, AMx, ANx, APx, AQx, CNx, CPx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, ATx, AWx, AXx, D5x, D6x v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, 9Qx, 9Rx, 9Sx, 9Tx, 9Ux, 9Vx, 9Wx, 9Xx, 9Yx, A2x, A4x, C9x, CAx, CEx, CFx, CGx,
Table 43.
Windows Vista Home Premium (32 bit) DVDs for R61, R61e, and R61i (some models) Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 7642-CTO, 25x, 26x, 27x, 28x, 2Cx, 2Dx, 2Ex, 2Gx v 7643-CTO, 3Hx, 3Jx, 3Mx, 3Nx v 7644-CTO, 48x, 4Ax, 4Lx, 4Mx, 4Nx, 4Rx, 4Sx, 7Kx, 7Lx, 7Mx, 7Qx, 7Rx v 7645-CTO, 5Bx, 5Cx, 5Dx, 5Gx, 5Hx v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO, 3Sx, 3Tx, A6x v 8918-CTO, 5Fx, 5Hx, 5Rx, ACx v 8919-CTO, 6Sx v 8920-CTO v 8927-CTO v 8928-CTO v 89
Table 44.
Windows Vista Home Premium (32 bit) DVDs for R61i (some models) Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 8914-CTO v 8918-CTO, ARx, ASx, ATx, CGx, CJx, CKx, CLx, DAx, DCx, DPx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, E4x, GBx, GFx, GVx, GYx v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, A6x, A7x, A8x, A9x, CBx, CCx, D2x, D3x, E6x, EGx, EPx, F2x, F5x v 7657-CTO R61, R61e, and R61i
Table 45.
Windows Vista Business (32 bit) DVDs for R61, R61e, and R61i (some models) Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 7642-CTO, 22x, 29x, 2Fx, 72x v 7643-CTO, 32x, 35x, 36x, 37x, 38x, 39x, 3Ax, 76x, 77x, 78x, 79x, 7Ax, 7Bx, 3Kx, 3Lx, 3Px v 7644-CTO, 42x, 43x, 44x, 45x, 4Hx, 4Px, 4Qx, 7Gx, 7Nx, 7Px v 7645-CTO, 52x, 53x, 54x, 55x, 5Ex, 5Fx, 7Sx, 7Tx, 7Ux, 7Vx v 7646-CTO, 62x, 63x, 64x, 6Ax, 6Bx, 66x, 68x, 69x v 7647-CTO v 7648-CTO v 8914-CTO, 20x, 23x, 3
Table 46.
Windows Vista Business (32 bit) DVDs for R61i Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 8914-CTO v 8918-CTO, CHx, CMx, DBx, DDx, DNx v 8919-CTO v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO, APx, AQx, ARx, ASx, AYx, AZx, B2x, B3x, D7x, D8x, E3x, E7x, EAx, FEx, FFx, FGx, FJx, FUx, G8x, G9x, GCx, GDx, GEx, GLx, GMx, GQx, GRx, GSx, GTx, GUx, GWx, GXx v 8933-CTO v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO, 9Mx, 9N
Table 47.
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 7642-CTO, 2Ax, 73x v 7643-CTO, 33x, 34x, 3Bx, 3Cx, 3Dx, 3Ex, 74x, 75x, 7Cx, 7Dx, 7Ex, 7Fx v 7644-CTO, 46x, 49x, 4Jx, 7Hx v 7645-CTO, 56x, 57x, 58x, 59x, 7Wx, 7Xx, 7Yx, 7Zx v 7646-CTO, 65x, 67x v 7647-CTO v 7648-CTO v 8914-CTO, 37x, 3Dx v 8918-CTO, 42x, 45x, 46x, 4Bx, 4Cx, 4Px, 4Qx, 4Vx, 4Wx, 53x, 54x, 55x, 56x, 5Ex, 60x, BHx, BJx, BNx, BPx, BSx, BTx, BWx, BXx v 8919-CTO, 62
Table 48.
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 7642-CTO v 7643-CTO v 7644-CTO v 7645-CTO v 7646-CTO v 7647-CTO v 7648-CTO v 8914-CTO v 8918-CTO v 8919-CTO, 6Wx, 6Z, AVx, DLx v 8920-CTO v 8927-CTO v 8928-CTO v 8929-CTO v 8930-CTO v 8932-CTO v 8933-CTO, EXx, FTx v 8934-CTO v 8935-CTO v 8936-CTO v 8937-CTO v 7649-CTO v 7650-CTO v 7657-CTO R61, R61e, and R61i (15.
Table 49.
Common service tools Table 50. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
232 ThinkPad R61, R61e, and R61i (15.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 42X3549_05 (1P) P/N: 42X3549_05
