User's Manual

3745 Panel Codes
Table 1-5 (Page 7 of 33). Panel Codes. An ñ following a panel code denotes that the code should 'Blink'.
Panel
Code
Definition
Action: Go to “3745 FRU Group
Table” on page 1-49
or to MAP number
11Dñ
ERROR IN SSB BYTE 1 AND 2 READ/WRITE A
SECTOR COMMAND
Exchange the FRU group 16
11Eñ
ADAPTER IN BUSY STATE IN TEST 10 BSTAT BITS
0,1 ARE NOT B'00' OR ADAPTER NOT ENABLE
BSTAT BIT 6 IS NOT ONE READ/WRITE A FULL
TRACK COMMAND
11Fñ
IOIRV REGISTER IS X'00' IN TEST 10 NO INTER-
RUPT RECEIVED READ/WRITE A FULL TRACK
COMMAND
120ñ
EIRV REGISTER IS NOT X'00' IN TEST 10
READ/WRITE A FULL TRACK COMMAND
121ñ
DATA TRANSMISSION ERROR HSTAT BITS
0,1,2,3,6,7 ARE NOT ZERO READ/WRITE A FULL
TRACK COMMAND
Exchange the FRU group 16
122ñ
DIFFERENT WRITTEN AND READ TRACKS
READ/WRITE A FULL TRACK COMMAND
123ñ
ERROR IN SSB BYTE 0 READ/WRITE A FULL
TRACK COMMAND
124ñ
ERROR IN SSB BYTE 1 AND 2 READ/WRITE A FULL
TRACK COMMAND
125ñ
ADAPTER IN BUSY STATE IN TEST 11 BSTAT BITS
0,1 ARE NOT B'00' OR ADAPTER NOT ENABLE
BSTAT BIT 6 IS NOT ONE READ/WRITE NO DATA
COMMAND
Exchange the FRU group 16
126ñ
IOIRV REGISTER IS X'00' IN TEST 11 NO INTER-
RUPT RECEIVED READ/WRITE NO DATA
COMMAND
127ñ
EIRV REGISTER IS NOT X'00' IN TEST 11
READ/WRITE NO DATA COMMAND
128ñ
DATA TRANSMISSION ERROR HSTAT BITS
0,1,2,3,6,7 ARE NOT ZERO READ/WRITE NO DATA
COMMAND
129ñ
DIFFERENT WRITTEN AND READ SECTORS
READ/WRITE NO DATA COMMAND
Exchange the FRU group 16
12Añ
ERROR IN SSB BYTE 0 READ/WRITE NO DATA
COMMAND
12Bñ
ERROR IN SSB BYTE 1 AND 2 READ/WRITE NO
DATA COMMAND
12Cñ
ADAPTER IN BUSY STATE IN TEST 12 BSTAT BITS
0,1 ARE NOT B'00' OR ADAPTER NOT ENABLE
BSTAT BIT 6 IS NOT ONE READ CHECK/WRITE
VERIFY COMMAND
12Dñ
IOIRV REGISTER IS X'00' IN TEST 12 NO INTER-
RUPT RECEIVED READ CHECK/WRITE VERIFY
COMMAND
Exchange the FRU group 16
12Eñ
EIRV REGISTER IS NOT X'00' IN TEST 12 READ
CHECK/WRITE VERIFY COMMAND
12Fñ
DATA TRANSMISSION ERROR HSTAT BITS
0,1,2,3,6,7 ARE NOT ZERO READ CHECK/WRITE
VERIFY COMMAND
130ñ
ERROR IN SSB BYTE 0 READ CHECK/WRITE
VERIFY COMMAND
131ñ
ERROR IN SSB BYTE 1 AND 2 READ CHECK/WRITE
VERIFY COMMAND
Exchange the FRU group 16
132ñ
DIFFERENT WRITTEN AND READ SECTORS READ
CHECK/WRITE VERIFY COMMAND
133ñ
ADAPTER IN BUSY STATE IN TEST 13 BSTAT BITS
0,1 ARE NOT B'00' OR ADAPTER NOT ENABLE
BSTAT BIT 6 IS NOT ONE ECC CORRECTION TEST
134ñ
IOIRV REGISTER IS X'00' IN TEST 13 NO INTER-
RUPT RECEIVED ECC CORRECTION TEST
Chapter 1. START: How to Begin Troubleshooting 1-21