User's Manual
Table Of Contents
- Contents
- Safety
- Chapter 1. Introducing the IBM xSeries 445 server
- Chapter 2. Configuring the server
- Using the Configuration/Setup Utility program
- Using the ServerGuide Setup and Installation CD
- Configuring the Gigabit Ethernet controller
- Using the Integrated System Management Firmware Update Utility program
- Using the LSI Logic Configuration Utility program
- Using ServeRAID Manager
- Remote Supervisor Adapters
- Using the PXE boot agent utility program
- Appendix A. Getting help and technical assistance
- Appendix B. Notices
- Edition notice
- Trademarks
- Important notes
- Product recycling and disposal
- Battery return program
- Electronic emission notices
- Federal Communications Commission (FCC) statement
- Industry Canada Class A emission compliance statement
- Australia and New Zealand Class A statement
- United Kingdom telecommunications safety requirement
- European Union EMC Directive conformance statement
- Taiwanese Class A warning statement
- Chinese Class A warning statement
- Japanese Voluntary Control Council for Interference (VCCI) statement
- Power cords
- Index
3.
If
you
are
installing
from
a
CD,
type:
d:\DD\WIN2000\SETUP,
where
d
is
the
drive
letter
of
the
DVD-ROM
drive.
4.
Follow
the
directions
that
display
on
the
screen.
5.
Go
to
“Configuring
the
remote
control
password”
on
page
63.
Installing
Windows
NT
ASM
device
drivers:
Select
one
of
the
following
methods
to
install
the
ASM
device
drivers
for
Windows
NT:
v
Non-interactive
The
non-interactive
method
for
installing
the
ASM
device
drivers
accepts
the
default
values
for
any
window
prompts
that
appear.
You
are
prompted
to
respond
only
if
an
error
occurs
during
installation.
v
Interactive
The
normal
(interactive)
method
for
installing
the
ASM
device
drivers
prompts
you
with
instructions
and
waits
for
you
to
respond
before
continuing
with
the
installation.
Note:
If
IBM
Netfinity
Director,
IBM
Director,
UM
Services,
or
IBM
Netfinity
Manager
is
running
on
the
server,
stop
the
system-management
application
before
proceeding.
Using
the
non-interactive
method:
Complete
the
following
steps
to
use
the
non-interactive
method.
1.
Open
a
Windows
NT
command
prompt;
then,
type
one
of
the
following
commands:
v
If
the
installation
is
from
a
diskette,
type:
a:\NT\SETUP
-q
(where
a
is
the
drive
letter
assigned
to
the
diskette
drive).
Press
Enter.
v
If
the
installation
is
from
a
CD,
type:
d:\DD\NT\SETUP
-q
(where
d
is
the
drive
letter
assigned
to
the
DVD-ROM
drive).
Press
Enter.
2.
Follow
the
instructions
that
appear
in
the
window.
3.
Go
to
“Configuring
the
remote
control
password”
on
page
63.
Using
the
interactive
method:
Complete
the
following
steps
to
use
the
interactive
method.
1.
Open
a
Windows
NT
command
prompt;
then,
type
one
of
the
following
commands:
v
If
the
installation
is
from
a
diskette,
type:
a:\NT\SETUP
(where
a
is
the
drive
letter
assigned
to
the
diskette
drive).
Press
Enter.
v
If
the
installation
is
from
a
CD,
type:
d:\DD\NT\SETUP
(where
d
is
the
drive
letter
assigned
to
the
DVD-ROM
drive).
Press
Enter.
2.
Follow
the
instructions
that
appear
in
the
window.
3.
Continue
with
“Configuring
the
remote
control
password”
on
page
63.
62
xSeries
445
Type
8870:
User’s
Guide