Enterprise Server S80 pSeries 680 Model S85 IBM Installation Guide SA38-0582-00
First Edition (November 2000) Before using this information and the product it supports, read the information in “Safety Notices” on page v, “Appendix B. Environmental Notices” on page 43, and “Appendix C. Notices” on page 45. ©International Business Machines Corporation 2000. All rights reserved. Note to U.S. Government Users - Documentation related to restricted rights - Use, duplication, or disclosure is subject to the restrictions set forth in the GSA ADP Schedule Contract with IBM Corp.
Contents Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . v Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . v Laser Safety Information . . . . . . . . . . . . . . . . . . . . . vi Data Integrity and Verification . . . . . . . . . . . . . . . . . . vii About This Book . ISO 9000 . . . . Online Publications. Related Publications Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
European Union (EU) Statement . . . . . . . . . . . . . . . . International Electrotechnical Commission (IEC) Statement . . . . . . . United Kingdom Telecommunications Safety Requirements . . . . . . . Avis de conformité aux normes du ministère des Communications du Canada . Canadian Department of Communications Compliance Statement . . . . . VCCI Statement . . . . . . . . . . . . . . . . . . . . . Electromagnetic Interference (EMI) Statement - Taiwan . . . . . . . . Radio Protection for Germany . . . . . .
Safety Notices A danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury. A caution notice indicates the presence of a hazard that has the potential of causing moderate or minor personal injury. Electrical Safety Observe the following safety instructions any time you are connecting or disconnecting devices attached to the workstation.
Laser Safety Information The optical drive in this system unit is a laser product. The optical drive has a label that identifies its classification. The label, located on the drive, is shown below. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 IEC 825:1984 CENELEC EN 60 825:1991 The optical drive in this system unit is certified in the U.S.
Data Integrity and Verification IBM computer systems contain mechanisms designed to reduce the possibility of undetected data corruption or loss. This risk, however, cannot be eliminated. Users who experience unplanned outages, system failures, power fluctuations or outages, or component failures must verify the accuracy of operations performed and data saved or transmitted by the system at or near the time of the outage or failure.
viii S80, S85 Installation Guide
About This Book This book provides information on how to setup and install the system, use diagnostics, use service aids, and verify system operation. This book also provides information to help you solve some of the simpler problems that might occur. ISO 9000 ISO 9000 registered quality systems were used in the development and manufacturing of this product. Online Publications RS/6000 publications are available online. To access the online books, visit our Web site at: http://www.rs6000.ibm.
v The 7133 SSA Disk System: Operator Guide, order number xxxxxxx, describes how to operate the 7133 SSA Disk System and how to install or replace disk drives to the system, and how to deal with problems encountered when using the system. v The 7133 SSA Disk Subsystem: Service Guide, order number xxxxxxx, is used by the service technician to repair system failures in the 7133 SSA Disk System.
Chapter 1. System Installation Procedure Follow the procedures in this chapter to install the Enterprise Server S80 and the p Series 680 Model S85. The estimated installation time for the system is: Install Activity 3.5 Hours Planning Activity 2.0 Hours ________________ _________ Total Time 5.5 Hours Step 1. Inventory v The About Your Machine listing is in a plastic bag attached to the outside of the carton. Check the listing to verify that you have all the items that were shipped with the system.
DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged.
Refer to ″Specifications″ in the Enterprise Server S80 p Series 680 Model S85 Service Guide, order number SA38-0560, for more planning information. Step 4. Check Customer Outlets Note: For a translation of this notice, see the System Unit Safety Information manual, order number SA23-2652. CAUTION: Do not touch the receptacle or the receptacle faceplate with anything other than your test probes before you have met the requirements in Step 8 below. __ 1.
__ 6. Have the customer turn on the branch circuit CB. Measure for appropriate voltages between phases. If no voltage is present on the receptacle case or grounded pin, the receptacle is safe to touch. __ 7. With an appropriate meter, verify that the voltage at the outlet is correct. __ 8. Verify that the grounding impedance is correct by using the ECOS 1020, 1023, B7106, or an appropriately approved ground impedance tester.
b. Adjust the height of the leveling feet by rotating the leveling feet either upward or downward according to the level of the surface on which the rack is placed. Repeat this for the remaining leveling feet as needed. c. When the rack is leveled, tighten the locking nuts on all of the leveling feet. Locking Nut Leveling Feet (4) 5. Align the slots in the stabilizer with the mounting holes in the bottom front of the I/O rack. 6. Ensure that the base of the stabilizer rests firmly on the floor. 7.
Mounting Screw 9. Hang the crank and tightening rod on the bracket near the bottom of the right wall inside the back of the rack. Tightening Rod Crank 10. Install the rear stabilizer on the I/O rack, as follows: a. Loosen the lower screws on the stabilizer assembly. b. Slide the stabilizer assembly onto the bottom of the rack. c. Install screws at the top of the stabilizer assembly and tighten. d. Tighten the lower screws on the stabilizer assembly.
e. Adjust the bolts to the floor to ensure that the stabilizer is level and does not move. 11. If head protectors are installed, remove them from diskette drives. Step 6A. Attach the I/O Rack to a Concrete Floor Perform this step if the I/O rack is to be attached to a concrete floor or a concrete floor beneath a raised floor. Notes: 1. Ensure that the primary I/O rack (the primary I/O rack contains the service processor) is positioned on the right side of the system rack when viewed from the front.
v To a concrete floor, continue with “Attaching the I/O Rack to a Concrete Floor”. v To a concrete floor below a raised floor, go to “Attaching the I/O Rack to a Concrete Floor Beneath a Raised Floor” on page 10. If you are not attaching the I/O rack to a concrete floor, continue with “Step 7. Attach the Front Electrical Outlet” on page 18. Attaching the I/O Rack to a Concrete Floor The customer is responsible for attaching the rack-mounting plates to the concrete floor.
Rack Mounting Bolts Mounting Holes Front of Rack Mounting Holes Holes for Anchor Bolts (10) Mounting Plate (2) Tapped Holes for Rack Mounting Bolts Location Marks (Drill One of These Two Marks) Location Marks (Drill One of TheseTwo Marks) Location Marks (Drill One of These Six Marks) 10. Drill one hole in each group of anchor bolt location marks as indicated on the marked floor. 11. Using at least three anchor bolts for each mounting plate, mount the two mounting plates to the concrete floor. 12.
15. Place the four plastic isolator pads under the four leveling feet, and then level the rack using the four adjustable leveling feet. 16. Tighten the locking nuts on the leveling feet. Leveling Foot (4) Rack-Mounting Bolts Rack-Mounting Bolts Front of Rack Plastic Isolator Washer (4) Plastic Isolator Pad (4) Mounting Holes Holes for Anchor Bolts Mounting Plates (2) Tapped Holes for Rack Mounting Bolts Location Marks 17. Tighten the four rack-mounting bolts into the two mounting plates. 18.
2. Place the two mounting plates in the approximate mounting locations under the rack. 3. To align the rack over the mounting plates, do the following: a. Place the four rack-mounting bolts through the mounting holes at the bottom of the rack. b. Position the mounting plates under the four rack-mounting bolts so that the mounting bolts are centered directly over the tapped holes. Insert the rack-mounting bolts three or four rotations into the tapped holes. 4.
Rack Mounting Bolts Mounting Holes Front of Rack Holes for Anchor Bolts (10) Tapped Holes for Rack Mounting Bolts Mounting Holes Mounting Plate (2) Raised Floor Panels Projection of Mounting Plates onto Concrete Floor 9. At the marked location of the tapped mounting holes, drill two holes approximately 1 inch to allow clearance for the ends of the two rack-mounting bolts. The ends of the rack-mounting bolts may protrude past the thickness of the mounting plate.
Rack Mounting Bolts Mounting Holes Front of Rack Holes for Anchor Bolts (10) Mounting Holes Mounting Plate (2) Tapped Holes for Rack Mounting Bolts Raised Floor Panels Location Marks (Drill One of These Two Marks) Location Marks (Drill One of These Two Marks) Location Marks (Drill One of These Six Marks) Projection of Mounting Plates onto Concrete Floor 13. Place the two mounting plates on the locations indicated on the marked raised-floor panel. 14.
c. Insert the rack-mounting bolts three to four rotations into the tapped holes. Note: The bottoms of the four leveling feet must be positioned over the four plastic isolator pads when the rack is leveled. If you are installing an AC powered rack, do not use the four plastic isolator pads. 18. Place the four plastic isolator pads under the four leveling feet, and then level the rack using the four adjustable leveling feet. 19. Tighten the locking nuts on the leveling feet.
Notes: 1. Ensure that the primary I/O rack (the primary I/O rack contains the service processor) is positioned on the right side of the system rack when viewed from the front. A clearance of 10 cm (4 inches) between the racks is required to allow access to the I/O rack door. 2. If you are attaching the system rack: v To a concrete floor, continue with “Attaching the System Rack to a Concrete Floor”.
b. Position the mounting plates under the four rack-mounting bolts so that the mounting bolts are centered directly over the tapped holes. c. Insert the rack-mounting bolts three or four rotations into the tapped holes. 4. Mark the floor around the edge of the mounting plates. 5. Remove the mounting bolts from the threaded holes. 6. Move the rack away from the mounting plates. 7. Mark the floor at the center of each hole in the mounting plate (including tapped holes). 8.
1. Install the 4 plate assemblies with the levelling feet, bushings, and washers. Make sure that the leveling feet are backed off the floor level to allow space for the mounting plates. 2. Place the mounting plates, front and rear, (note that they are different) in the approximate mounting position under the system rack. 3. To align the system rack over the mounting plate, do the following: a.
concrete floor, some of the drilled holes may not be usable. For each mounting plate, select at least three usable holes, two that are on opposite sides and opposite ends of each other, and one hole at the center. 10. Drill one hole in each group of anchor bolt location marks as indicated on the marked raised-floor panel. 11. Project the holes now in the raised-floor panel down to the concrete floor below.
Front of Rack Electrical Outlet Assembly Power Cable From Power Source Mounting Plate Mounting Screws 2. Place the ground-cable lug through the mounting hole of the mounting plate. 3. Connect the long end of the ground cable to the threaded side of the ground-cable lug (inside mounting plate), and then install and tighten the ground-lug nut. Note: The two remaining connections of the ground cable are done in “Step 8. Attach the Rear Electrical Outlet” on page 22. Chapter 1.
Front of Rack Long End of Ground Cable Ground Lug Nut Mounting Hole Mounting Plate Y-End of Ground Cable Ground Lug Long End of Ground Cable Ground Connector (Short End of Ground Cable) 4. Find the crank (for installing the mounting screws) located inside the rear of the rack near the bottom of the right wall.
Crank 5. Align the holes of the mounting plate with the holes on the rack, and then install the two mounting screws. 6. Using the crank, tighten the two mounting screws. Chapter 1.
Front of Rack Crank Mounting Plate Mounting Screws 7. Store the crank inside the rear of the rack near the bottom of the right wall. Notes: 1. If the customer does not want to connect an electrical outlet to the front mounting plate, install the mounting plate without the electrical outlet. 2. The customer is responsible for providing and connecting the electrical outlet assembly.
2. After the customer has connected the power cable from the customer power source to the electrical outlet assembly, mount the electrical outlet assembly to the mounting plate using the two mounting screws (provided by the customer). 3. Place the ground cable lug through the mounting hole of the mounting plate. 4. Connect the short ground cable to the threaded side of the ground cable lug, and then install and tighten the ground lug nut. Chapter 1.
5. Attach the mounting plate to the rack by installing and tightening the three mounting screws.
6. Connect the ground connector of the ground cable to the ground bus bar. 7. If a drawer was removed from the bottom position of the rack, reinstall it. 8. Close the rear door of the rack. Chapter 1.
Step 9. Remove the Shipping Brackets and Install Covers 1. Remove any shipping materials from the system rack, I/O racks and from the front and rear of the I/O drawers. 2. Remove the disk drive cover from the front of each I/O drawer. Inspect the disk drives to ensure that the disk-drive carriers are all seated completely and that the carrier latch is in the horizontal locked position.
3. Install any covers and shields that you have removed, or that were shipped separately. 10 EIA Unit Drawer Disk Drive Cover Step 10. Install the I/O Rack Door Guide 1. Locate the I/O rack door guide. 2. Position the door guide as shown. 3. Using a 3mm allen wrench, fasten the door guide to the I/O rack as shown. Chapter 1.
Door Guide Step 11. Connect the Operator Panel Cable and the JTAG Cable Between the Racks Using the cables provided, connect the cables between the system rack and the primary I/O drawer. Refer to “Appendix D. Cabling the System Rack and I/O Rack” on page 47 for connector locations for these cables. Step 12. Connect RIO and SPCN Cables Between the Racks Using the cables provided, connect the RIO and SPCN cables between the system rack and the I/O drawers. Refer to “Appendix D.
Step 14. Update the Device Records External devices used with the S80 and S85 systems are connected to connectors on the primary I/O drawer or to adapters that are installed inside any of the I/O drawers. Update the “System Records” in “Appendix E. System Records” on page 63 to reflect the configuration of the system adapters and devices that are installed. Step 15.
v PDB circuit breakers CP1 - CP6 are set correctly (refer to “I/O Rack Rear Locations” on page 49 for locations) v Customer’s supply voltage is correct. If any failures occur, refer to ″Maintenance Analysis Procedures (MAPs)″ in the Enterprise Server S80 p Series 680 Model S85 Service Guide, order number SA38-0560.
If so, see ″Capacity Upgrade on Demand Processor Enabling″ in Capacity Upgrade on Demand Installing and Upgrading Processors, order number SA38-0583, for information regarding installing and enabling this feature. __ 3. If you decided to delay installing any optional devices, you might want to install these now. Some options you can install may come with a diskette that contains device drivers, configuration files, or test programs.
32 S80, S85 Installation Guide
Chapter 2. Using the System Verification Procedure The system verification procedure is used to check the system for correct operation. If you are analyzing a hardware problem, see ″Hardware Problem Determination″ in Enterprise Server S80, p Series 680 Model S85 User’s Guide, order number SA38-0557. Step 1. Considerations before Running This Procedure Notes: 1.
a. When the keyboard indicator appears, press the 5 key on the keyboard to load the standalone diagnostics or press the 6 key to load the online diagnostics. b. Enter any requested passwords. c. Follow the instructions to select a console. 6. When the Diagnostic Operating Instructions display, go to “Step 3. Running System Verification”.
3. This completes the system verification. Report the SRN if you received one to the service organization. To do a normal boot, turn off the system unit and wait 30 seconds, and then turn the system power on. Chapter 2.
36 S80, S85 Installation Guide
Chapter 3. Installing Options for Your System There are no customer-installable options for the Enterprise Server S80 or the p Series 680 Model S85. The Capacity Upgrade On-Demand feature may be installed. See Capacity Upgrade on Demand Installing and Upgrading Processors, order number SA38-0583, for information regarding installing and enabling this feature.
38 S80, S85 Installation Guide
Appendix A. Communications Statements The following statement applies to this product. The statement for other products intended for use with this product appears in their accompanying documentation. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
International Electrotechnical Commission (IEC) Statement This product has been designed and built to comply with IEC Standard 950. United Kingdom Telecommunications Safety Requirements This equipment is manufactured to the International Safety Standard EN60950 and as such is approved in the UK under the General Approval Number NS/G/1234/J/100003 for indirect connection to the public telecommunication network.
Electromagnetic Interference (EMI) Statement - Taiwan The following is a summary of the EMI Taiwan statement above. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user will be required to take adequate measures. Radio Protection for Germany Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom 9.Nov.92 das EG–Konformitätszeichen zu führen. Der Aussteller der Konformitätserklärung ist die IBM Germany.
42 S80, S85 Installation Guide
Appendix B. Environmental Notices Product Recycling and Disposal This unit contains materials such as circuit boards and connectors with lead that require special handling and disposal at end of life. Before this unit is disposed of, these materials must be removed and recycled or discarded according to applicable regulations. This manual contains specific information on batteries where applicable. This product may contain nickel-cadmium and/or lithium batteries.
44 S80, S85 Installation Guide
Appendix C. Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer’s representative for information on the products and services currently available in your area. Any reference to the manufacturer’s product, program, or service is not intended to state or imply that only that product, program, or service may be used.
46 S80, S85 Installation Guide
Appendix D. Cabling the System Rack and I/O Rack The minimum system consists of two racks. The system rack contains the system processors, memory and supporting hardware. The I/O rack contains I/O drawer(s) with PCI adapters, disk drives, and media drives. The S80 and S85 must have a minimum of one I/O drawer. This drawer is called the primary I/O drawer and it contains the service processor for the system. Additional I/O drawers can be added to the system. These drawers are called secondary I/O drawers.
Connecting JTAG and Operator Panel Cables Use the following figure to connect the JTAG and operator panel (OP) cables.
I/O Rack Rear Locations The following figure shows the rear of an I/O rack. 10 EIA unit I/O drawers can be installed, as shown in the figure. 10 EIA Unit I/O Drawers Primary I/O Drawer Secondary I/O Drawer Power Distribution Bus (CP1 - CP6) Appendix D.
I/O Drawer Locations This section shows component locations for the 10 EIA unit I/O drawer. 10 EIA Unit I/O Drawer Front View Note: The SCSI IDs shown for media devices indicate how these devices are set when shipped from the factory. 1. Indicator Panel 2. Blower 1 (left) 3. Blower 3 (center) 4. Blower 2 (right) 5. Hot Swap Disk Drive Bays 6.
10 EIA Unit I/O Drawer Rear View 1. PCI adapter slots (1 - 7) 2. PCI adapter slot 8, service processor card and JTAG cable in primary I/O drawer (drawer 0) 3. Parallel connector 4. Keyboard connector 5. Mouse connector 6. Reserved 7. Reserved 8. PCI adapter slots (9 - 14) 9. Right power supply 10. Power cord connector for right power supply 11. Fans (mounted on front end of right power supply) 12. Right power supply, power good LED 13. SPCN2 connector 14. SPCN1 connector 15. Serial port S2* 16.
17. 18. 19. 20. 21. 22. Note: In an RS/6000 SP environment, there is normally a cable attached from this port to the SP Control Workstation. To directly attach a TTY terminal to this port, the cable to the SP Control Workstation must be disconnected. Be sure to reconnect this cable after servicing the system.
10 EIA Unit I/O Drawer System board Locations J1 RIO bus J2 RIO bus J3 SPCN connector J4 PCI slot 2, controller 1 J5 PCI slot 3, controller 1 J6 PCI slot 4, controller 1 J7 PCI slot 6, controller 0 J8 PCI slot 7, controller 0 J9 PCI slot 8, controller 0 Appendix D.
54 J10 PCI slot 11, controller 2 J11 PCI slot 12, controller 2 J12 PCI slot 13, controller 2 J13 PCI slot 1, controller 1 J14 PCI slot 5, controller 0 J15 PCI slot 9, controller 3 J16 PCI slot 10, controller 3 J17 PCI slot 14, controller 2 J18 JTAG connector J19 Display indicator panel (DIP) connector J21 I35 SCSI backplane connector J22 Power distribution board (PDB) card connector J23 PCI slot (1-8) power connector J24 PCI slot (9-14) power connector J25 +12 vdc, −12 vdc, and
Service Processor Card Locations J1 JTAG connector to system rack J2 Serial port connector to inside bulkhead card J3 Speaker connector J4 Diskette drive connector J5 Parallel port connector J6 Keyboard/mouse connector to inside bulkhead card J16 Write protect DASD FLASH (if jumper is on pins) J17 Operator panel connector from the system rack J18 Test Port 0 J19 Test Port 1 J20 Test Port 2 J22 Write protect boot FLASH (if jumper is set between pins 2 and 3) Appendix D.
Fan Monitor Control (FMC) Card Locations (10 EIA Unit I/O Drawer) J2 J4 J1 J6 J3 J5 J1 To Power Distribution Board J2 Fan 2 (Left Blower) J3 Fan 1 (Center Blower) J4 Fan 3 (Right Blower) J5 Power Supply and Fans 4, 5, 6, 7 (Power Supply Fan Assemblies) J6 To PCI Connectors Power Distribution Board Locations 56 J1 Power supply docking connector J2 Power supply docking connector J3 I/O planar connector J4 Fan monitoring card connector S80, S85 Installation Guide
J5 +12 V dc, −12 V dc J6 +5 V dc J7 +5 V dc J8 I35 SCSI backplane power connector J9 Media bay power connector J10 +5 V dc J11 Fan monitoring card connector Connecting RIO and SPCN Cables The RIO and SPCN cables provide two functions in the S80 and S85 system: remote data bus connection and power control. The following basic rules must be followed when connecting these two types of cables: v The I/O drawers must be connected in a loop fashion for both the RIO cables and the SPCN cables.
System Rack Attached to One I/O Drawer Drawer 0, Primary SPCN 1 2 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 System Rack Attached to Two I/O Drawers Drawer 0 SPCN 1 2 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 Drawer 1 J14 J11 SPCN 0, J15 SPCN 1, J16 OR 58 S80, S85 Installation Guide RIO 1 SPCN 1 2 RIO 0 RIO 1
Drawer 0 Drawer 2 SPCN 1 2 RIO 0 SPCN 1 2 RIO 1 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 System Rack Attached to Three I/O Drawers Drawer 2 Drawer 0 SPCN 1 2 RIO 0 SPCN 1 2 RIO 1 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 J14 J11 RIO 1 Drawer 1 SPCN 0, J15 SPCN 1, J16 SPCN 1 2 RIO 0 RIO 1 System Rack Attached to Four I/O Drawers Appendix D.
Drawer 2 Drawer 0 SPCN 1 2 RIO 0 RIO 1 Drawer 3 SPCN 1 2 RIO 0 SPCN 1 2 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 RIO 1 RIO 1 Drawer 1 SPCN 1 2 RIO 0 RIO 1 SPCN Cabling The following figures provide cabling examples for all valid cabling configurations. Match your configuration to the correct figure and connect your SPCN cables as shown.
Drawer 0 SPCN 1 2 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 RIO 1 Drawer 1 or 2 SPCN 1 2 RIO 0 RIO 1 System Rack Attached to Three I/O Drawers Drawer 2 Drawer 0 SPCN 1 2 RIO 0 SPCN 1 2 RIO 1 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 Drawer 1 SPCN 1 2 J14 J11 SPCN 0, J15 SPCN 1, J16 RIO 1 RIO 0 RIO 1 System Rack Attached to Four I/O Drawers Appendix D.
Drawer 2 Drawer 0 SPCN 1 2 RIO 0 RIO 1 Drawer 3 SPCN 1 2 RIO 0 62 SPCN 1 2 RIO 1 S80, S85 Installation Guide RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 RIO 1 Drawer 1 SPCN 1 2 RIO 0 RIO 1
Appendix E. System Records Use this appendix to keep a record of your system configuration. Pages are provided for system information, cabling diagrams, I/O cards installed, and disk drives installed. Record the Identification Numbers Record and retain the following information.
Drawer 2 Drawer 0 SPCN 1 2 RIO 0 RIO 1 Drawer 3 SPCN 1 2 RIO 0 SPCN 1 2 RIO 0 RIO 2 RIO 3 RIO 0 RIO 1 J14 J11 SPCN 0, J15 SPCN 1, J16 RIO 1 RIO 1 Drawer 1 SPCN 1 2 RIO 0 RIO 1 S80 and S85 System Rack Cabling Configurations - SPCN Cabling Use the following diagram to record the SPCN cabling configuration from the system rack to the I/O drawer(s).
Primary I/O Drawer Device Records Use the following tables to keep a record of the options installed in or attached to your system. This information can be helpful to you or your service representative when you install additional options in your server. Table 1.
Table 1. Internal and External Options in Primary Drawer (0) (continued) Serial Port 2 Refer to the following diagram of your server’s banks/bays when completing Table 2. 10 EIA Unit I/O Drawer Table 2. Internal Files and Devices in Primary Drawer (0) 10 EIA Unit I/O Drawer 66 Location/Drive SCSI ID Drive Description Bank B, Bay 1 Non-SCSI 3.5-Inch 1.
Table 2. Internal Files and Devices in Primary Drawer (0) 10 EIA Unit I/O Drawer (continued) Location/Drive Bank A, Bay 1 SCSI ID 5 Bank C, Drive 1 8 Bank C, Drive 2 9 Bank C, Drive 3 10 Bank C, Drive 4 11 Bank C, Drive 5 12 Bank C, Drive 6 13 Bank D, Drive 1 8 Bank D, Drive 2 9 Bank D, Drive 3 10 Bank D, Drive 4 11 Bank D, Drive 5 12 Bank D, Drive 6 13 Drive Description Appendix E.
Additional I/O Drawer Device Records Use the following tables to keep a record of the options installed in or attached to your system. This information can be helpful to you or your service representative when you install additional options in your server. Table 3.
Table 4. Internal and External Options in Secondary Drawer (2) (continued) Expansion Slot 14 Expansion Slot 13 Expansion Slot 12 Expansion Slot 11 Expansion Slot 10 Expansion Slot 9 Expansion Slot 8 Expansion Slot 7 Expansion Slot 6 Expansion Slot 5 Expansion Slot 4 Expansion Slot 3 Expansion Slot 2 Expansion Slot 1 Table 5.
Table 5.
Index A P about this book ix B preface ix product disposal 43 publications, online ix battery disposal, recycling 43 R C cables JTAG 48 operator panel 48 RIO 57 SPCN 57, 60 cabling 47 connecting cables 47 connecting the system rack and I/O rack 47 D device records 65, 68 internal and external options 65, 68 internal files and devices 66 F fan monitor control card 56 FMC card 56 I records, device 65, 68 recycling 43 related publications ix RIO cabling configurations S safety notices v laser com
72 S80, S85 Installation Guide
Reader’s Comments — We’d Like to Hear From You Title: Enterprise Server S80 p Series 680 Model S85 Installation Guide Order Number: 09P1686 Overall how satisfied are you with the information in this book? Overall Satisfaction Very Satisfied h Satisfied h Neutral Dissatisfied Very Dissatisfied h h h How satisfied are you that the information in this book is: Accurate Complete Easy to find Easy to understand Well organized Applicable to your tasks Very Satisfied h h h h h h Satisfied h h h h h h Neut
Cut or Fold Along Line Fold and Tape Please do not Staple Fold and Tape NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL POSTAGE WILL BE PAID BY ADDRESSEE Information Development Department H6DS-9561 11400 Burnet Road Austin, TX 78758-3493 Fold and Tape Please do not Staple Fold and Tape Cut or Fold Along Line 74 S80, S85 Installation Guide
75
IBMR Part Number: 09P1686 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber.
