Server User Manual

358 iSeries and AS/400e System Builder
3575 model matrix summary
Model Capacity Capacity Cartridges Drives
L06 300 GB 900 GB 60 2
L12 600 GB 1.8 TB 120 2 to 4
L18 900 GB 2.7 TB 180 2 to 6
L24 1.2 TB 3.6 TB 240 2 to 6
L32 1.6 TB 4.8 TB 324 2-6
Notes:
򐂰 14 cartridge slots can be configured for bulk I/O within the library. This reduces the maximum cartridges per library by 14 and
reduces the maximum capacity of the library.
򐂰 Model L12 can be upgraded to Model L18 to increase the capacity of the library.
򐂰 Model L24 can be upgraded to Model L32 to increase the capacity of the library.
򐂰 All drives installed at the plant are 3570 Model C tape drives.
򐂰 The IBM marketing configurator allows only one drive per IOP port to enable maximum performance. Installing more than one
3570 Magstar MP Model C tape drive on an IOP port might impact system performance. When using the #6501 Tape/Disk Device
Controller to attach the 3575, one port on the #6501 must remain unused.
IBM TotalStorage 3582 Ultrium Tape Library
3582 L23
#8103
#8104
#8105
#8203
#8204
#8205
#5096
#5099
#5301
#5302
3582 Ultrium Tape Library
The IBM 3582 Ultrium Tape Library is designed for desktop operation, but an optional rack mounting kit allows
installation into an ANSI/EIA standard 19-inch rack with four EIA units of space. The 3582 tape library can have one
or two IBM LTO Ultrium 2 tape drives. Ultrium 2 drives have a native data transfer rate of 35 Mbps and cartridge
capacity of 200 MB. Data compression (LTO-DC) provides an effective data rate of 70 Mbps and up to 400 MB
cartridge capacity. The 3582 has two 7-cartridge removable magazines, nine rear fixed slots, and one I/O slot for a
total of 24 tape cartridge slots, providing a maximum capacity of 9.6 TB. Multipath architecture allows the 3582 to be
partitioned into two logical libraries.
Tape drive features:
LTO Ultrium 2 LVD Drive Sled (HD68 connection)
LTO Ultrium 2 HVD Drive Sled (HD68 connection)
LTO Ultrium 2 Fibre Drive Sled with a LC Fibre Channel interface
These are plant only features and cannot be intermixed. Each feature can be ordered by specifying quantity one or
two.
LTO Ultrium 2 LVD Drive Sled (HD68 connection)
LTO Ultrium 2 HVD Drive Sled (HD68 connection)
LTO Ultrium 2 Fibre Drive Sled with a LC Fibre Channel interface
These features provide a second drive that is
client installed. They can be specified with the initial order or ordered
as an MES. One of these features can be intermixed with one #8103, #8104, or #8105 in any combination.
Adapters supported:
LVD Drive Sled (#8103 or #8203)
#5702 PCI-X Ultra Tape Controller, #5705 PCI-X Tape/DASD Controller,
#5712 PCI-X Tape/DASD Controller (LVD, VHDCI), #5715 PCI-X Tape/DASD Controller (LVD, VHDCI)
HVD Drive Sled (#8104 or #8204)
#2729 PCI Magnetic Media Controller (HVD, HD68)
#2749 PCI Ultra Magnetic Media Controller (HVD, HD68)
#6534 Magnetic Media Controller (HVD, HD68)
Fibre Drive Sled (#8105 or #8205)
#2765 PCI Fibre Channel Tape Controller (LC)
#5704 PCI-X Fibre Channel Tape Controller (LC)
Cable features:
Interposer SC-LC
VHDCI/HD68 Cable/Interposer
0.4 m HD68/HD68 SCSI cable (use to daisy-chain two tape drives on the same SCSI bus)
2.5 m (8-ft) HD68/HD68 SCSI cable