Internal IDE CD-ROM Drive User's Guide
Table Of Contents
- Contents
- About this book
- Safety information
- Part 1: Installation and user’s guide
- Appendix A. Customizing device driver configurationsettings
- Appendix B. Problem solving
- Appendix C. Help and service information
- Appendix D. Product warranties and notices
- Warranty Statements
- IBM Statement of Limited Warranty for United States, PuertoRico, and Canada (Part 1 - General Terms)
- IBM Statement of Warranty Worldwide except Canada,Puerto Rico, Turkey, United States (Part 1 - General Terms)
- Part 2 - Worldwide Country-Unique Terms
- Notices
- Trademarks
- Federal Communications Commission (FCC) statement
- obi32eng.pdf
- OBI32FR.PDF
- Table des matières
- About this book
- Safety information
- Chapitre 1 : Installation et utilisation
- Annexe A. Customizing device driver configurationsettings
- Annexe B. Problem solving
- Annexe C. Help and service information
- Annexe D. Product warranties and notices
- Warranty Statements
- IBM Statement of Limited Warranty for United States, PuertoRico, and Canada (Part 1 - General Terms)
- IBM Statement of Warranty Worldwide except Canada,Puerto Rico, Turkey, United States (Part 1 - General Terms)
- Part 2 - Worldwide Country-Unique Terms
- Notices
- Trademarks
- Federal Communications Commission (FCC) statement
- obi32sp.pdf
- Contenido
- Acerca de este manual
- Información sobre seguridad
- Parte 1: Instalación y guía del usuario
- Apéndice A. Personalización de los valores deconfiguración de los controladores de dispositivos
- Apéndice B. Resolución de problemas
- Apéndice C. Help and service information
- Apéndice D. Product warranties and notices
- Warranty Statements
- IBM Statement of Limited Warranty for United States, PuertoRico, and Canada (Part 1 - General Terms)
- IBM Statement of Warranty Worldwide except Canada,Puerto Rico, Turkey, United States (Part 1 - General Terms)
- Part 2 - Worldwide Country-Unique Terms
- Notices
- Trademarks
- Federal Communications Commission (FCC) statement
- d4ql1mst.pdf
- Indice
- Informazioni su questo manuale
- Informazioni sulla sicurezza
- Parte 1: Guida per l’utente e all'installazione
- Appendice A. Personalizzazione delle impostazioni diconfigurazione dei driver di periferica
- Appendice B. Risoluzione dei problemi
- Appendice C. Informazioni sull'assistenza tecnica
- Appendice D. Informazioni particolari e sulla garanzia
- d4ql1mst.pdf
- OBI32FR.PDF
Appendix B. Problem solving
Computer problems can be caused by hardware, software, or user error. Using
the information in this section, you might be able to solve problems yourself or
gather helpful information you can pass on to a service technician. You might
also need to refer to your computer, operating-system, or audio-adapter
publications.
Problem descriptions
Review the following list for any problem descriptions that might fit your
situation.
Your computer or CD-ROM drive does not operate correctly
or the Busy indicator light does not come on.
Take the following actions:
1. Make sure that the CD is inserted with the label side up or facing out if the
drive is installed vertically.
2. Make sure that all devices are properly connected to the computer and the
electrical outlet.
3. Turn off the computer, unplug the cables from the electrical outlets for your
computer and all attached devices, and remove the computer cover.
4. Make sure that all power and IDE cables are securely attached. Disconnect
the IDE cable and check for bent or misaligned pins. If you do not find any
problems, reconnect the cable. Replace the computer cover, and reattach all
cables and power cords. Turn on the computer and attempt to open the CD
tray by pressing the Eject/Load button. If the tray fails to open and the
Busy indicator light does not display, turn off the computer and try
replacing the 4-pin dc power cable.
5. Make sure that the color-coded edge on the IDE cable aligns with pin 1 on
the IDE port and is closest to the power cable on the CD-ROM drive. See
“Step 6. Attaching the cables to the drive” on page 1-6.
6. Make sure that the IDE cable is connected to the correct IDE port
connection. See “Step 3. Selecting the IDE port” on page 1-4 for more
information.
7. Check the CD-ROM drive and any other device on the IDE cable for the
proper jumper configuration settings. See “Step 4. Setting the configuration
jumper” on page 1-5 for more information.
8. Check to see if the middle connector on the IDE cable is attached to the
IDE port on the system board. If it is, remove the connector and reattach
the cable correctly. The middle port is used only if you are connecting two
devices to the IDE port. If there are two devices on the IDE port, attach the
© Copyright IBM Corp. 2000 B-1