Eden/Ezra Processor User's Manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating jumpers
- 2.4 Locating Connectors
- 2.5 Setting Jumpers
- 2.6 Clear CMOS (JP4)
- 2.7 Installing DIMMs
- 2.8 IDE, CDROM hard drive connector (CN14, CN16)
- 2.9 Solid State Disk
- 2.10 Floppy drive connector (CN18)
- 2.11 Parallel port connector (CN15)
- 2.12 Keyboard and PS/2 mouse connector (CN25)
- 2.13 Power & HDD LED, Reset Button Connector (CN13, CN22)
- 2.14 Power connectors (CN27, CN5, FAN1)
- 2.15 ATX power control connector (CN3, CN23)
- 2.16 IR connector (CN24)
- 2.17 Audio interfaces (CN4, CN2)
- 2.18 COM port connector (CN19)
- 2.19 VGA/LCD/LVDS interface connections
- 2.20 TV-out interface (optional) (CN1)
- 2.21 Ethernet configuration
- 2.22 Watchdog timer configuration
- 2.23 USB connectors (CN20, CN28)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- 4.2.1 Entering setup
- 4.2.2 Standard CMOS Features setup
- 4.2.3 Advanced BIOS Features setup
- 4.2.4 Advanced Chipset Features setup
- 4.2.5 Integrated Peripherals
- 4.2.6 Power Management Setup
- 4.2.7 PnP/PCI Configurations
- 4.2.8 PC Health Status
- 4.2.9 Frequency/Voltage Control
- 4.2.10 Load Optimized Defaults
- 4.2.11 Set Password
- 4.2.12 Save & Exit Setup
- 4.2.13 Exit Without Saving
- Chapter 5 PCI SVGA Setup
- Chpater 6 Audio Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104-Plus Modules
- Appendix C Pin Assignments
- C.1 CPU Fan Power Connector (FAN 1)
- C.2 Ethernet 10/100Base-T Connector (CN12)
- C.3 Audio Connector (CN4)
- C.4 Audio In Connector (CN2)
- C.5 Main Power Connector (CN5)
- C.6 Keyboard and PS/2 Mouse Connector (CN25)
- C.7 Floppy Disk Drive Connector (CN18)
- C.8 PC/104 plus Connectors (CN17)
- C.9 IDE Hard Drive Connector (CN14, CN16)
- C.10 Parallel Port Connector (CN15)
- C.11 Power & HDD LED Connector(CN13)
- C.12 Reset Button Connector (CN22)
- C.13 USB Connector (CN20, CN28)
- C.14 LCD Inverter Backlight Connector (CN6)
- C.15 IR Connector (CN24)
- C.16 CRT Display Connector (CN8)
- C.17 TV (video) Out Connector (CN1)
- C.18 Flat Panel Connector (CN11)
- C.19 Extended Flat Panel Display Connector (CN10)
- C.20 LCD Signal Mapping
- C.21 LVDS Connector (CN9)
- C.22 Peripheral Power Connector (CN27)
- C.23 COM Port Connector (CN19)
- C.24 CompactFlash Card Connector (CN26)
- C.25 ATX Power Feature Connector (CN3)
- Appendix D System Assignments
- Appendix E Optional Extras for the PCM-9575
- Appendix F Mechanical Drawings
vi
2.14.2Main power connector, +5 V, +12 V (CN5) .......................... 17
2.14.3CPU Fan power supply connector (FAN1) ............................. 17
2.15 ATX power control connector (CN3, CN23).................. 17
2.15.1ATX feature (CN3), soft power switch conn (CN23)............. 17
Figure 2.3: Wiring for ATX soft power switch function .... 18
2.16 IR connector (CN24)....................................................... 18
2.17 Audio interfaces (CN4, CN2).......................................... 18
2.17.1Audio connector (CN4) ........................................................... 19
2.17.2CD audio input connector (CN2) ............................................ 19
2.18 COM port connector (CN19) .......................................... 19
2.18.1COM2 RS-232/422/485 setting (JP6) ..................................... 19
2.19 VGA/LCD/LVDS interface connections ........................ 20
2.19.1CRT display connector (CN8)................................................. 20
2.19.2Flat panel display connector (CN11)....................................... 20
2.19.3Extension flat panel connector (CN10)................................... 20
2.19.4LVDS LCD panel connector (CN9)........................................ 20
2.19.5Panel type selection (S1) ......................................................... 20
Table 2.4: S1 Panel Type select........................................ 21
2.20 TV-out interface (optional) (CN1) .................................. 21
2.21 Ethernet configuration..................................................... 22
2.21.1100Base-T connector (CN12) ................................................. 22
2.21.2Network boot........................................................................... 22
2.21.3LAN controller power select (JP2).......................................... 22
Table 2.5: LAN controller power select (JP2).................. 22
2.22 Watchdog timer configuration ........................................ 22
2.22.1Watchdog timer action (JP5)................................................... 23
Table 2.6: Watchdog timer action (JP5) ........................... 23
2.23 USB connectors (CN20, CN28)...................................... 23
Chapter 3 Software Configuration .................................25
3.1 Introduction ..................................................................... 26
3.2 Connections to Three Standard LCDs............................. 27
3.2.1 Connections (640 x 480 TFT color LCD) .............................. 27
Table 3.1: Connections to Toshiba LTM10C209A .......... 27
3.2.2 Connections (1024 x 768 TFT color LCD) ............................. 28
Table 3.2: Connections to Toshiba LTM15C151A .......... 28
3.2.3 Connections (800 x 600 TFT color LCD) .............................. 29
Table 3.3: Connections to Toshiba LTM12C275A .......... 29
3.3 Ethernet software configuration ...................................... 30