Eden/Ezra Processor User's Manual
Table Of Contents
- Contents
- Chapter 1 General Information
- Chapter 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating jumpers
- 2.4 Locating Connectors
- 2.5 Setting Jumpers
- 2.6 Clear CMOS (JP4)
- 2.7 Installing DIMMs
- 2.8 IDE, CDROM hard drive connector (CN14, CN16)
- 2.9 Solid State Disk
- 2.10 Floppy drive connector (CN18)
- 2.11 Parallel port connector (CN15)
- 2.12 Keyboard and PS/2 mouse connector (CN25)
- 2.13 Power & HDD LED, Reset Button Connector (CN13, CN22)
- 2.14 Power connectors (CN27, CN5, FAN1)
- 2.15 ATX power control connector (CN3, CN23)
- 2.16 IR connector (CN24)
- 2.17 Audio interfaces (CN4, CN2)
- 2.18 COM port connector (CN19)
- 2.19 VGA/LCD/LVDS interface connections
- 2.20 TV-out interface (optional) (CN1)
- 2.21 Ethernet configuration
- 2.22 Watchdog timer configuration
- 2.23 USB connectors (CN20, CN28)
- Chapter 3 Software Configuration
- Chapter 4 Award BIOS Setup
- 4.1 System test and initialization
- 4.2 Award BIOS setup
- 4.2.1 Entering setup
- 4.2.2 Standard CMOS Features setup
- 4.2.3 Advanced BIOS Features setup
- 4.2.4 Advanced Chipset Features setup
- 4.2.5 Integrated Peripherals
- 4.2.6 Power Management Setup
- 4.2.7 PnP/PCI Configurations
- 4.2.8 PC Health Status
- 4.2.9 Frequency/Voltage Control
- 4.2.10 Load Optimized Defaults
- 4.2.11 Set Password
- 4.2.12 Save & Exit Setup
- 4.2.13 Exit Without Saving
- Chapter 5 PCI SVGA Setup
- Chpater 6 Audio Setup
- Chapter 7 PCI Bus Ethernet Interface
- Appendix A Programming the Watchdog Timer
- Appendix B Installing PC/104-Plus Modules
- Appendix C Pin Assignments
- C.1 CPU Fan Power Connector (FAN 1)
- C.2 Ethernet 10/100Base-T Connector (CN12)
- C.3 Audio Connector (CN4)
- C.4 Audio In Connector (CN2)
- C.5 Main Power Connector (CN5)
- C.6 Keyboard and PS/2 Mouse Connector (CN25)
- C.7 Floppy Disk Drive Connector (CN18)
- C.8 PC/104 plus Connectors (CN17)
- C.9 IDE Hard Drive Connector (CN14, CN16)
- C.10 Parallel Port Connector (CN15)
- C.11 Power & HDD LED Connector(CN13)
- C.12 Reset Button Connector (CN22)
- C.13 USB Connector (CN20, CN28)
- C.14 LCD Inverter Backlight Connector (CN6)
- C.15 IR Connector (CN24)
- C.16 CRT Display Connector (CN8)
- C.17 TV (video) Out Connector (CN1)
- C.18 Flat Panel Connector (CN11)
- C.19 Extended Flat Panel Display Connector (CN10)
- C.20 LCD Signal Mapping
- C.21 LVDS Connector (CN9)
- C.22 Peripheral Power Connector (CN27)
- C.23 COM Port Connector (CN19)
- C.24 CompactFlash Card Connector (CN26)
- C.25 ATX Power Feature Connector (CN3)
- Appendix D System Assignments
- Appendix E Optional Extras for the PCM-9575
- Appendix F Mechanical Drawings
Table of Contents
v
Contents
Chapter 1 General Information ........................................1
1.1 Introduction ....................................................................... 2
1.2 Features ............................................................................. 3
1.3 Specifications .................................................................... 4
1.3.1 Standard EBX SBC Functions .................................................. 4
1.3.2 VGA/LCD Interface .................................................................. 4
1.3.3 LVDS: Supports 2 Channel (2 x 18 bit) LVDS interface.......... 5
1.3.4 Audio function........................................................................... 5
1.3.5 TV-out (optional) ...................................................................... 5
1.3.6 PCI bus Ethernet interface......................................................... 5
1.3.7 Mechanical and Environmental................................................. 5
1.4 Board layout: dimensions.................................................. 6
Figure 1.1: Board layout: dimensions ................................... 6
Chapter 2 Installation ........................................................7
2.1 Jumpers.............................................................................. 8
Table 2.1: Jumpers .............................................................. 8
2.2 Connectors......................................................................... 8
Table 2.2: Connectors ......................................................... 8
2.3 Locating jumpers............................................................. 10
Figure 2.1: Jumper locations ............................................... 10
2.4 Locating Connectors ....................................................... 11
Figure 2.2: Connectors (component side) ........................... 11
2.5 Setting Jumpers ............................................................... 12
2.6 Clear CMOS (JP4) .......................................................... 13
Table 2.3: CMOS clear (JP4)............................................ 13
2.7 Installing DIMMs............................................................ 14
2.8 IDE, CDROM hard drive connector (CN14, CN16)....... 14
2.8.1 Connecting the hard drive ....................................................... 14
2.9 Solid State Disk............................................................... 15
2.9.1 CompactFlash (CN26)............................................................. 15
2.10 Floppy drive connector (CN18) ...................................... 15
2.10.1Connecting the floppy drive .................................................... 15
2.11 Parallel port connector (CN15) ....................................... 16
2.12 Keyboard and PS/2 mouse connector (CN25) ................ 16
2.13 Power & HDD LED, Reset Switch (CN13, CN22) ........ 16
2.13.1Power & HDD LED (CN13) ................................................... 17
2.13.2Reset switch (CN22) ............................................................... 17
2.14 Power connectors (CN27, CN5, FAN1).......................... 17
2.14.1Peripheral power connector, -5 V, -12 V (CN27) ................. 17