Product introduction and how to use How to use the water tank and mop assembly Single suction & Roller brush 1.Fetch out the dust box firstly. 2.Open the seal button of the water tank, and inject cleaning water, and cover the sealing lid and assemble the tank into robot. 3.Push the mopping assembly horizontally into the robot after matching the right snap joint position. 1.Press the buckle on the roller brush cover , then remove the roller brush cover and brush.
Precautions before using 1.Please clean up small objects, fragile articles, cables, curtain ropes, etc. scattered on the ground before use to prevent entanglement or damage of the property. 2.The users with a duplex structure such as stairs etc. in their homes shall specially note that it is strictly forbidden to use the product in the fenceless suspending environment, which is higher than that of the family activities.
Quick instruction 2. Charge the robot vacuum cleaner on the charging stand 1.Charging stand Take the charging stand out from the package. Signal indication light Power interface Charging terminal 01. After cleaning, the machine will automatically return to the charging stand for charging. If it cannot return to the charging stand, try to remove the obstacles around the charging stand or take the cleaner back to the charging stand for charging.
Quick instruction 3.On/Off 5. Connection network for the machine 01. In case the main machine is being charged on the charging stand, it will automatically turn on. Before connecting the network, please make sure that the mobile phone and the machine are within the WiFi cover-age and as close as possible to the router. 02.During its charging, the machine cannot be turned off.
Product maintenance Cleaning of rolling brush Cleaning of side brush 1.Turn the machine and press the buckle on the rolling brush cover from both ends to remove the rolling brush. 1.Turn the machine, lift the left and right brushes up and pull them out. 2.Clean the windings on the left and right brushes and their bearings. Rolling brush cover 3.Align the side brush with its bearing on the machine and press firmly to install the left and right brushes.
Product maintenance Battery Universal wheel 1.The high-performance lithium-ion battery pack is built in the machine. And the battery has no memory effect and it is no need to worry about repeated charging/discharging. 1.1.Universal wheel. 2. Clean the hair and dust on the wheel and bearings. 3. Assemble the universal wheel again after dried completely 2.In order to maintain the best performance, keep the machine charging on the charging stand if it does not work. 3.
Product parameters Parameters of main machine Parameters of charging stand ITEM PARAMETERS Dimensions L346*W340*H99mm Battery Lithium battery,4500mAH Host Weight PARAMETERS ITEM Dimension L165*W142*H100mm 3.1±0.1KG Rated input 100-240V 50/60Hz Connection Method WiFi connection Rated output 24.0V/1.0A Rated Voltage 14.
Voice prompts and trouble-shooting If the machine is faulty during operation, the power key quick flashes in red color. Please refer to the following voice prompts or APP prompt to solve the abnormal problem. Sn. Voice prompt Cause Trouble-shooting 1 The dust box is missing. The cleaning is triggered during removing of the dust box. Re-install the dust box or pause the cleaning task of the machine. 2 AH OH, the radar on the top seems to be covered.
Voice prompts and trouble-shooting Sn. Voice prompt Cause Trouble-shooting 12 AH OH, the side brush seems to be stucked. Pls help me. The side brush is stuck or entangled. Please check if the side brush is entangled and clean it. 13 I need battery charging, my master. The main battery is too low to return to the charging stand Please take the host back to the charging stand 14 Recharging failed. Pls put me back to the charging base, my master.
FAQ Failure Trouble-shooting It cannot be turned on. The battery is low, please charge it before use. The ambient temperature is over low or over high, please use it in the range of 0°C-40°C. It cannot be charged. The charging stand is not powered, please make sure the power is connected successfully. Poor contact of the charging electrode, please clean the charging stand electrode and the machine electrode. The machine cannot be returned for charging.
Safety information Service restrictions 01.The product is only for the cleaning of the floor in the home environment and do not use it outdoors (such as open balcony), non-ground (such as sofa, coffee table, etc.), commercial or industrial environment. 02.Do not use the product in a suspended environment (such as duplex floors, home tops, etc. ) to avoid property damage and personal injury caused by falling of the device. 03.Do not use the product in an environment above 40 0 C or below -10 0 C. 04.
Safety information Battery and charging 01.Do not use any battery, charging stand or charger from third-party. 02.Please make sure that the voltage used is correct. 03.Do not disassemble, repair or modify the battery or the charging stand. 04.Do not place the charging stand and the main machine close to the heat source, such as heating radiators, induction cookers, ovens, etc. 05.Do not wipe anywhere of the product with a damp cloth or any liquid. 06.
Safety information FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
