Owner's manual

Appendix
List of Parameters
378
Appendix
I/O Parameters
No. Parameter name
Default value
(Reference)
skrameRtinUegnartupnI
83 (PC/TP SIO reservation) 0
84 (PC/TP SIO reservation) 0
85 (PC/TP SIO reservation) 0
86 (PC/TP SIO reservation) 0
87 (PC/TP SIO reservation) 0
88 (PC/TP SIO reservation) 0
89 (PC/TP SIO reservation) 0
90 Usage of SIO channel 0
opened to user
(AUTO mode)
0 0 ~ 9 0: Open SEL program
1: Open SEL program (Connect PC/TP when both devices
are closed = Used exclusively by the manufacturer)
2: IAI protocol B (Slave)
91 Station code of SIO channel
0 opened to user
153 0 ~ 255 Valid only with IAI protocol.
92 Baud rate type of SIO
channel 0 opened to user
0 0 ~ 5 0: 9.6, 1: 19.2, 2: 38.4, 3: 57.6, 4: 76.8,
5: 115.2 kbps
93 Data length of SIO channel
0 opened to user
8 7 ~ 8
94 Stop bit length of SIO
channel 0 opened to user
1 1 ~ 2
95 Parity type of SIO channel 0
opened to user
0 0 ~ 2 0: None 1: Odd 2: Even
96 Receive operation type of
SIO channel 0 opened to
user
0 0 ~ 1 0: Forcibly enable receive after send
1: Do not forcibly enable receive at send
97 IAI-protocol minimum
response delay for SIO
channel 0 opened to user
0 0 ~ 999 msec Valid only with IAI protocol.
98 (Reservation of SIO
channel 0 opened to user)
0
99 (Reservation of SIO
channel 0 opened to user)
0
100 ~
115
SIO system reservation 0 0H ~
FFFFFFFFH
116 (For expansion) 0
117 (For expansion) 0
118 (For expansion) 0
119 (For expansion) 0
120 Network Attribute 1
121 Network Attribute 2
122 Network Attribute 3
123 Network Attribute 4
124 Network Attribute 5
125 Network Attribute 6
126 Network Attribute 7
127 Network Attribute 8
128 Network Attribute 9
0H ~ Bit 0 to 3: System reservation
Bit 0 to 11: System reservation
Bit 12 to 15: Future expansion
Bit 12 to 23: System reservation
Bit 24 to 27: Selection of Profibus H/L byte SWAP
Bit 16 to 27: Link timeout value at fieldbus initialization
Bit 4 to 11: Network link error check timer value (10msec)
I/O Parameters No.18 = Effective only when set to 1
(100msec)
(Main application version 0.36 or later)
Bit 0 to 11: Value added for “PC·TP reconnection delay time
at software reset” (sec) when fieldbus is used
(Main application Ver. 0.36 or later)
* Valid values 0 to 500(sec)
(0: without SWAP, 1: with SWAP)
* When set to 0, generates system error
immediately at network link error occurrence.
1H
0H ~FH
0H ~0H
0H ~0H
0H ~1E32H
0H ~7D007D0H
0H ~5050214H
0H ~0H
FFFFFFFFH
0H ~C80000H
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH
FFFFFFFFH