Owner's manual

41
4. Description of Operating Functions
List of ACON-SE Functions
ż: Direct control U: Indirect control ×: Invalid
Operation by position number specification Operation by numeric specification
DeviceNet gateway CC-Link gateway
Serial communication
Gateway position number
specification mode
Serial communication
Direct numeric
specification mode
Command specification
mode
Position data limiting
mode
Normal positioning mode
Push & hold enabled
mode
Command specification
mode
Home return operation żżżżżżżżż Positioning operation U Specify the position
table no.
U Same as at the left ż Specify the position
data directly.
ż Specify the position
data directly.
ż Specify the position
data directly.
ż Specify the position
table no.
ż Specify the position
data directly.
ż Specify the position
data directly.
ż Specify the position
data directly.
ż Specify the position
data directly.
ż Specify the position
table no.
Speed setting U Set it in the position
table.
U Same as at the left ż Specify a numeric
value directly.
ż Specify a numeric
value directly.
U Set it in the position
table.
U Set the parameter. ż Specify a numeric
value directly.
ż Specify a numeric
value directly.
U Set it in the position
table.
Acceleration/deceleration setting
U Set the acceleration
and deceleration separately in the position table.
U Same as at the left
ż Specify a numeric
value as the acceleration/ deceleration.
ż Specify a numeric
value as the acceleration/ deceleration.
U Set the acceleration
and deceleration separately in the position table.
ż Set the parameter as
the acceleration/ deceleration.
ż Specify a numeric
value as the acceleration/ deceleration.
ż Specify a numeric
value as the acceleration/ deceleration.
U Set it in the position
table.
Operation at different acceleration/deceleration
U Set the acceleration
and deceleration separately in the position table.
U Same as at the left
ż The acceleration/
deceleration data is accepted at positioning start time. Therefore, to specify the deceleration different from the acceleration, change the acceleration/ deceleration data during movement and restart the controller.
ż The acceleration/
deceleration data is accepted at positioning start time. Therefore, to specify the deceleration different from the acceleration, change the acceleration/ deceleration data during movement and restart the controller.
U Set the acceleration
and deceleration separately in the position table.
× Since parameter
setting is performed as the acceleration/ deceleration, the acceleration and deceleration cannot be set separately.
ż The acceleration/
deceleration data is accepted at positioning start time. Therefore, to specify the deceleration different from the acceleration, change the acceleration/ deceleration data during movement and restart the controller.
ż The acceleration/
deceleration data is accepted at positioning start time. Therefore, to specify the deceleration different from the acceleration, change the acceleration/ deceleration data during movement and restart the controller.
U Set the acceleration
and deceleration separately in the position table.
Pitch (incremental) feeding U Set it in the position
table.
U Same as at the left ż If bit 2 of the CTLF
FRQWUROIODJLVVHWWR³´ incremental operation starts.
× Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
U Set it in the position
table.
× Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
× Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
× Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
U Set it in the position
table.
Push & hold operation U Set it in the position
table.
U Same as at the left żż Specify a numeric
value directly.
U Set it in the position
table.
× × ż Direct numeric
specification
U Set it in the position
table.
Speed change during movement
U Combine two or more
position nos.
U Same as at the left ż The speed data is
accepted at positioning start time. Therefore, to change the speed during movement, change the speed data during movement and restart the controller.
ż The speed data is
accepted at positioning start time. Therefore, to change the speed during movement, change the speed data during movement and restart the controller.
U Combine two or more
position nos.
× ż Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
ż Direct processing
cannot be performed. Issue a position command by adding the same distance to or subtracting it from the current position with the host PLC.
U Combine two or more
position nos.
Pause żżżżżżżżż Zone signal ż Set it in the position
table or with the user parameter. Output signal: PZONE, =21(=21(
ż Set it with the user
parameter. Output VLJQDO=21( ZONE2
ż Set it with the user
parameter. 2XWSXWVLJQDO=21( ZONE2
× Simple direct operation: ×
Positioner operation: ż
× × × Simple direct operation: ×
Positioner operation: ż
Power saving mode × × × × × × × × × Position table Required Required Not required Not required Required Not required Required Required Required