Quick Start Guide

Quick Start Guide
This is a quick walkthrough of the set up process. For complete documentations
and quick start guides, please visit http://support.IAdea.com.
Box Content
CARE AND WARNING CAUTION
Europe – EU Declaration of Conformity
IAD-18010 series
Screw
M3*13
Screw
M3*6
Port Connections
1
Screw Hole
2
Camera*
3
Microphone*
4
LED
6
MicroSD card slot
7
ADB
8
3.5mm audio
9
USB port
10
Reset
11
USB port
12
Ethernet RJ45
13
Power LED
14
12V DC power
15
Expansion*
16
Kensington Lock
17
VESA mount (MIS-D75)
Screw spec: M4
5
NFC/RFID reader
* The functions marked with "*" only appear on certain models.
MicroSD
ADB Audio Power
LED
USB Reset USB
Ethernet
DC Expansion
43
1
6
7
8
9
10
11
17
16
2
4
12
13 14 15
1
11
11
5
x 2
(1 Spare)
x 3
(1 Spare)
Room booking
panel
Mounting plate Glass mount
sticker
Front View
261.7*181.6(mm)
Mounting guide
sheet
Glass mount
cover sheet
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This device complies with the essential requirements of the Radio Equipment Directive
(2014/53/EU). The following test methods have been applied in order to prove presumption
of conformity with the essential requirements of the Radio Equipment Directive This
equipment is compliant with Class A of EN55032. In a residential environment this
equipment may cause radio interference.
The suitable temperature for the Colour Monitor and sccessories is 0°C-50°C.
Adaptor with ferrite must be used with this equipment to ensure compliance with the Class
A FCC limits.
Power Adapter information:
Model No.: WB-24J12R
INPUT: 100-240V~50/60Hz
OUTPUT: 12 2.0A
Correct Disposal of this product. This marking indicates that this product
should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
“FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the
FCC & CE’s RF exposure guidelines, place the product at least 20cm from near by
persons.”
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
- Replacement of a battery with an incorrect type that can be defeat a safeguard;
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas.
Risk of explosion if the battery is replaced by an incorrect type
Wait one-half hour after switching off before handling parts
company Name: IAdea Corporation
Address: 3F, No. 21, Lane 168, Xingshan Road,Neihu Dist. Taipei, 114 Taiwan
Tel: [phone]
Q41G78SP05904A
Installation height :<2M