Instruction Manual

2
 Installation Notes:
1. Please use point-to-point Unshielded Twisted Pair wire, 24-16 AWG, Category 2, 3, 4, 5, or 6.
2. Please measure the wire distance, Use only transceivers that are designed for that distance.
3. Please make sure the pair of wires carrying the video signal is sent as a twisted pair (e.g. the Blue-white/White-blue
wires twisted together as a pair), not a “split-pair” (e.g. blue-white conductor, part of one pair / orange-white conductor,
part of another pair).
 Installation Warning:
1. Please DO NOT USE SHIELD TWISTED PAIR WIRE. This will cause severe degradation on distance performance and
reduce the inherent interference immunity.
2. Please DO NOT have “bridge-taps” or loading coils in installation.
3. If the phone company provides the cable runs between buildings, make sure it’s “dry copper”.
4. Due to near-end cross talk, don’t send a transmitted and a received signal in the same wire bundle. For safety, DO
NOT put UTP cable in the same conduit as high-voltage wiring.
 Specification:
Item Model
I
R
-650636-F60 (40/80/120)
Ima
g
e Device 1/3“ SONY EXview HAD CCD II (Effio-E)
Effective Picture Elements PAL: 1024(H)x596 (V); NTSC: 1028(H)x508(V)
Horizontal Resolution Color: 650TVL; B/W: 700TVL
Minimum Illumination Color: 0.03Lux@F1.0, B/W: 0 Lux (IR LED on)
Wide D
y
namic Ran
g
e ATR Digital WD (ATR: Adaptive Tone-curve Reproduction)
S/N Ratio More than 50dB (AGC Off)
Shutter Speed Control AUTO (1/50(60) ~ 1/100,000 sec.)
Lens 6 mm / F2.0 (optional: 4mm/8m
m
/120m
m
)
Video Output RJ-45 connector; BNC composite connector (Option)
Gain Control Auto (4 steps)
White Balance ATW / PUSH / USER define / ANTI CR / MANUAL / PUSH LOCK
Back Li
g
ht Compensation HLC / BLC / OFF
Gamma Characteristic 0.45
Da
y
/Ni
g
ht Mode Color / B&W / AUTO / Ext.
Control Parameters Menu OSD (With an optional OSD cable con
t
rol)
Flicker Less O
N
/OFF
D
y
namic Noise Reduction 2D
Motion Detection ON / OFF (24x16 Zones)
Privac
y
Mas
k
ON / OFF (8
p
rogrammable mosaic zones)
Surge Protector
Video: Peak Inverse Blocking Voltage: VPIB = 100V;
Peak Pulse Current: Ipp=44A; Clamping Voltage: 10V @ Ipp= 5A
Power: Max. Energy: 3.6J (@10/1000μ);
Clamping Voltage: 16.8KA(1Time)/8.4KA (2Times) @ 8/20μs (1 Time);
Insulation Resistance: ≧10000MΩ
Waterproo
f
IP 67
Infrared Luminar
y
36
p
ieces Ø5 IR-LED
Transmission Distance Video / Power up 300 meters (Cat. 5 or above)
Power Consumption
DC 24V/140mA max, IR OFF: DC 24V/25mA
Operation Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH
Dimension/Wei
g
ht 85 (W) x 185 (H) x 240 (L) mm / 0.8Kg (Including
b
racket)