FCC Statement This equipment has been strictly tested and reached to Class A, pursuant to part 15 of the FCC rules, which focus on providing reasonable protection against harmful exterior interference when the equipment is operated in a commercial environment. While the equipment running, it maybe cause a strong electromagnetic wave with constant frequency, which may interrupt the radio communication if the user does not installed and used in accordance with the product user manual.
About This Guide About This Guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols to use throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you must follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
Important Safeguards and Warning Important Safeguards and Warning It is not recommended to install this product by unqualified person. The method and material of installation should be insured for the weight of the product and enclosure as pan/tilt, camera lens, and so on Stop using and power off the product if any unusual smell or smoke comes from the camera. Do not install the camera in an intermittent lighting environment.
Product Introduction Chapter 1 Product Introduction It can control output decoders, integrated camera, speed dome, or integrated PT unit. It can also be used in our DVR system. 1-1. Product Package Content Please check the package content by the following list. Joystick Keyboard (2D or 3D or 4 D) x 1 pcs Phone Box x 1 pcs DC 9V/1A Switching Power Adapter x 1 pcs Flat Cable with RJ45 Jack x 1 pcs User Manual x 1 pcs 1-2. Technical Parameters 1.
Function Description 1-3. Product Overview FSKY-100 Connection Diagram 1. Before power it, please check the cables, and make sure they are right connection. 2. Move the 2D, 3D or 4D joystick up/down/right/left to change the Speed dome pan or tilt direction, the moving speed increases as the offset. Turning the knob on the 3D joystick can control the camera TELE/WIDE and the 4D joystick provide a additional affirm function when push the top (red color) button of joystick.
Function Description Keypad and LCD panel Function Description Front Panel Back Panel D C A: Power input: Connect with DC9V power supply.
Function Description 3. CAM Select camera ID: Enter the Speed dome ID (0-255) by the number key then press CAM key. i.e. Number + CAM . The number will be displayed after item CAM on the LCD. For example: You want to select the ID 128 PTZ camera, press “ 1 “ + “ 2 “ + “ 8 “ and “ CAM “ key at a time. The LCD will show CAM=128, repeat the same process to select and other ID. 4. MON Reverse. 5.
Function Description 8. SCAN. (360°pan auto scan or 3 D Scanner) For FDPI-27X/35X/36X, FDPI-220, FDMO-27X/35X/36X, PTZWO-220 and SDCI-220 model: Press key SCAN. The LED gets turned on, and 2 points auto scan begins. Press key SCAN again. The LED gets turned off, and auto scan stop. For SDCI-220, FTWO-100 and FTCI-100 model: Press key 53 + CALL, star to Auto Scan function. Move the Joystick to stop Auto Scan function. 9. SHIFT Press key SHIFT, it gets turned on, and SHIFT is in effect.
Function Description 14. ENTER Press key ENTER, the Number input and setting area will be confirmed. 15. CLEAR Press key CLEAR, the Number input area will reset 16. PRESET Set up the Presets: Move the joystick, to adjust Pan/Tilt/Zoom of camera to select the surveillance position. Input number and then press [PRESET] key. i.e. N + PRESET Clear the presets: Input the preset number, and press [SHIFT] + [CLEAR] key. i.e. Number + SHIFT + CLEAR key. 17. MUX-C: Revere 18.
Function Description 1-4. Setup the Keyboard parameters Please follow the steps below to setup keyboard parameters. Step 1. Press the [SHIFT] + [MENU] key and below picture will be shown. Step 2. Enter the 4 numbers password and below picture will be shown. PASSWORD ： The default is 0000. SET UP1 >MODE: ： BAUD RATE： PROTOCOL 3D PELCO-P 9600 Step 3: Move joystick up or down to select parameter, which you want to modify. The selected item will show a “> “ mark.
Function Description 1-5. The function description of Keyboard parameters MODE: You can select the joystick type. 2D/3D/4D: for 2D/3D/4D joystick operation. PROTOCOL: The FSKY-100 keyboard provides Pelco P and D for selection. INITIAL SET: Enable the default setting. SET UP1 The default setting is off. >MODE: ： BAUD RATE： PROTOCOL 3D PELCO-P 9600 PASSWORD: Provide 4 umbers Password to protect the parameters setting. The default is 0000.
Function Description 1-5 Inner connection diagram S / L B / L B / R O / R B / K Y / L R / D G / R Connect O/R with RS-485+ A (Y) Connect S/L with RS-485- B (Z) There is a diagram on the box, please take it off before using.
