User Manual

...........continued
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
ECM 5206
68
31 C E Aftertreatment 1 Outlet NOx Sensor
Closed Loop Operation- Condition
Exists
ECM 5206
68
31 C L Aftertreatment 1 Outlet NOx Sensor
Closed Loop Operation- Condition
Exists
ECM 5207
16
3 C F Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Above Normal, or Shorted to High
Source
ECM 5207
16
4 C F Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Below Normal, or Shorted to Low
Source
ECM 5207
16
3 C E Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Above Normal, or Shorted to High
Source
ECM 5207
16
3 C L Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Above Normal, or Shorted to High
Source
ECM 5207
16
4 C E Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Below Normal, or Shorted to Low
Source
ECM 5207
16
4 C L Aftertreatment 1 Diesel Exhaust Flu-
id Dosing Valve 1 Heater - Voltage
Below Normal, or Shorted to Low
Source
ECM 5207
84
3 C F Fan Blade Pitch Position Sensor Cir-
cuit - Voltage Above Normal, or
Shorted to High Source
ECM 5207
84
4 C F Fan Blade Pitch Position Sensor Cir-
cuit - Voltage Below Normal, or Shor-
ted to Low Source
ECM 5207
84
5 C F Fan Blade Pitch - Mechanical system
not responding or out of adjustment
ECM 5207
91
2 C F Engine Boost Curve Selection - Data
erratic, intermittent or incorrect
ECM 5207
91
2 C E Engine Boost Curve Selection - Data
erratic, intermittent or incorrect
ECM 5207
91
2 C L Engine Boost Curve Selection - Data
erratic, intermittent or incorrect
ECM 5208
08
31 C F Engine Emergency Shutdown Switch
Actived - Condition Exists
ECM 5208
08
31 C E Engine Emergency Shutdown Switch
Actived - Condition Exists
ECM 5208
08
31 C L Engine Emergency Shutdown Switch
Actived - Condition Exists
ECM 5208
09
31 C F Excessive Time Since Last Engine
Air Shutoff Maintenance Test - Con-
dition Exists
ECM 5208
09
31 C E Excessive Time Since Last Engine
Air Shutoff Maintenance Test - Con-
dition Exists
ECM 5208
09
31 C L Excessive Time Since Last Engine
Air Shutoff Maintenance Test - Con-
dition Exists
ECM 5208
26
12 C F Aftertreatment Diesel Oxidation Cat-
alyst Temperature Sensor Module -
Bad Intelligent Device or Component
ECM 5208
26
16 C F Aftertreatment Diesel Oxidation Cat-
alyst Temperature Sensor Module -
Data Valid But Above Normal Oper-
ating Range - Moderately Severe
Level
ECM 5208
26
3 C F Aftertreatment Diesel Oxidation Cat-
alyst Temperature Sensor Module -
Voltage Above Normal or Shorted to
High Source
ECM 5208
26
9 C F Aftertreatment Diesel Oxidation Cat-
alyst Temperature Sensor Module -
Abnormal Update Rate
continued..........
...........continued
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
ECM 5209
53
3 C E Aftertreatment Diesel Exhaust Fluid
Dosing Unit Relay Feedback- Volt-
age Above Normal or Shorted to
High Source.
ECM 5209
53
3 C L Aftertreatment Diesel Exhaust Fluid
Dosing Unit Relay Feedback- Volt-
age Above Normal or Shorted to
High Source.
ECM 5209
53
4 C E Aftertreatment Diesel Exhaust Fluid
Dosing Unit Relay Feedback- Volt-
age Below Normal or Shorted to Low
Source.
ECM 5209
53
4 C L Aftertreatment Diesel Exhaust Fluid
Dosing Unit Relay Feedback- Volt-
age Below Normal or Shorted to Low
Source.
ECM 5209
68
19 C E Machine Constrained Operation- Re-
ceived Network Data in Error. The
received J1939 datalink message
was not valid.
ECM 5209
68
19 C L Machine Constrained Operation- Re-
ceived Network Data in Error. The
received J1939 datalink message
was not valid.
ECM 5209
68
9 C E Machine Constrained Operation- Ab-
normal Update Rate. No Communi-
cation or an invalid data transfer rate
has been detected on the J1939 data
link between the ECM and the ma-
chine electronic control unit.
ECM
5209
68
9 C L Machine Constrained Operation- Ab-
normal Update Rate. No Communi-
cation or an invalid data transfer rate
has been detected on the J1939 data
link between the ECM and the ma-
chine electronic control unit.
ECM
521 2 C F Brake Pedal Position - Data erratic,
intermittent or incorrect
ECM 521 2 C E Brake Pedal Position - Data erratic,
intermittent or incorrect
ECM 521 2 C L Brake Pedal Position - Data erratic,
intermittent or incorrect
ECM 5210
02
31 C E Engine Cranks Slowly - Condition
Exists
ECM 5210
02
31 C L Engine Cranks Slowly - Condition
Exists
ECM 5210
32
14 C E Aftertreatment System Assembly -
Special Instructions
ECM 5210
32
14 C L Aftertreatment System Assembly -
Special Instructions
MCU 5211 9 * L SPEEDLIMIT_PROP1 Timeout of
CAN-message SpeedLimit_Prop1
from Vehicle controller
MCU 5212 9 * L SPEEDLIMIT_PROP2 Timeout of
CAN-message SpeedLimit_Prop2
from Vehicle controller
ECM 5221
83
1 Y E EGR high temperature thermistor er-
ror
ECM 5221
83
1 Y L EGR high temperature thermistor er-
ror
ECM 5221
84
1 Y E EGR low temperature thermistor er-
ror
ECM 5221
84
1 Y L EGR low temperature thermistor er-
ror
ECM 5222
43
5 Y E Starting aid relay disconnection
ECM 5222
43
5 Y L Starting aid relay disconnection
ECM 5222
43
6 Y E Starting aid relay GND short circuit
ECM 5222
43
6 Y L Starting aid relay GND short circuit
continued..........
83
6 SPN 5~