User Manual

...........continued
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
ECM 623465 13 Y E Injector (No. 4 cylinder) correc-
tion value error
ECM 623465 13 Y L Injector (No. 4 cylinder) correc-
tion value error
ECM 624 5 P E Amber Warning Lamp : Current
Below Normal
ECM 624 5 P L Amber Warning Lamp : Current
Below Normal
ECM 624 6 P E Amber Warning Lamp : Current
Above Normal
ECM 624 6 P L Amber Warning Lamp : Current
Above Normal
ECM 625 9 C F Proprietary Datalink Error
(OEM/Vehicle Datalink) - Abnor-
mal update rate
ECM 625 9 C E Proprietary Datalink Error
(OEM/Vehicle Datalink) - Abnor-
mal update rate
ECM 625 9 C L Proprietary Datalink Error
(OEM/Vehicle Datalink) - Abnor-
mal update rate
ECM 625 2 C F Komnet Datalink Cannot Trans-
mit - Data Erratic, Intermittent,
or Incorrect. Communications
within the OEM datalink network
is intermittent.
ECM 626 1 C F Start Assist Device - Canister
Empty (Ether Injection)
ECM 626 18 C F Start Enable Device 1 Canister
Empty (Ether Injection) - Data
Valid But Below Normal Operat-
ing Range
ECM 626 3 C F Start Enable Device 1 Circuit
(Ether Injection) - Voltage above
normal, or shorted to high
source
ECM 626 4 C F Start Enable Device 1Circuit
(Ether Injection) - Voltage below
normal, or shorted to low source
ECM 626 18 C E Start Enable Device 1 Canister
Empty (Ether Injection) - Data
Valid But Below Normal Operat-
ing Range
ECM 626 18 C L Start Enable Device 1 Canister
Empty (Ether Injection) - Data
Valid But Below Normal Operat-
ing Range
ECM 626 3 C E Start Enable Device 1 Circuit
(Ether Injection) - Voltage above
normal, or shorted to high
source
ECM 626 3 C L Start Enable Device 1 Circuit
(Ether Injection) - Voltage above
normal, or shorted to high
source
ECM 626 4 C E Start Enable Device 1Circuit
(Ether Injection) - Voltage below
normal, or shorted to low source
ECM 626 4 C L Start Enable Device 1Circuit
(Ether Injection) - Voltage below
normal, or shorted to low source
ECM 626 5 P E Engine Start Enable Device 1 :
Current Below Normal
ECM 626 5 P L Engine Start Enable Device 1 :
Current Below Normal
ECM 626 6 P E Engine Start Enable Device 1 :
Current Above Normal
ECM 626 6 P L Engine Start Enable Device 1 :
Current Above Normal
ECM 626 11 C F Start Assist Device Control Cir-
cuit Error (Ether Injection)
ECM 627 12 C F Injector Power Supply - Bad In-
telligent Device or Component
continued..........
...........continued
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
ECM 627 12 C E Injector Power Supply - Bad in-
telligent device or component
ECM 627 12 C L Injector Power Supply - Bad in-
telligent device or component
ECM 627 2 C E Power Supply Lost With Ignition
On - Data Erratic, Intermittent,
or Incorrect
ECM 627 2 C L Power Supply Lost With Ignition
On - Data Erratic, Intermittent,
or Incorrect
ECM 627 2 C F Power Supply : Power Lost With
Ignition On - Data Erratic, Inter-
mittent, or Incorrect
ECM 628 9 C F Proprietary Datalink Error
(OEM/Vehicle Datalink) Abnor-
mal Update Rate. The ECM
cannot communicate with the
immobilizer anti-theft system.
ECM 629 31 C F At Least One Unacknowledged
Most Severe Fault - Condition
Exists
ECM 629 12 C E Engine Control Module Critical
Internal Failure - Bad intelligent
device or component
ECM 629 12 C L Engine Control Module Critical
Internal Failure - Bad intelligent
device or component
ECM 629 12 C F Engine Control Module Warning
Internal Hardware Failure - Bad
intelligent device or component
ECM 629 31 C E At Least One Unacknowledged
Moderately Severe Fault - Con-
dition Exists
ECM 629 31 C L At Least One Unacknowledged
Moderately Severe Fault - Con-
dition Exists
ECM 629 2 C F Fuel Pump Control Module,
Electronic Calibration Code Er-
ror
ECM 629 9 C F The ECM expected information
from a multiplexed device but
did not receive it soon enough,
or did not receive it at all.
TCU 63 * * L DRIVING MODE SIGNAL
TCU 63 * * F DRIVING MODE SIGNAL
ECM 630 12 Y E EEPROM memory deletion error
ECM 630 12 Y L EEPROM memory deletion error
ECM 630 13 C F Engine Control Module – out of
calibration
ECM 630 12 C E Engine Control Module Calibra-
tion Memory - Bad intelligent de-
vice or component
ECM 630 12 C L Engine Control Module Calibra-
tion Memory - Bad intelligent de-
vice or component
ECM 630 13 C E Electronic Calibration Code In-
compatibility - Out of Calibration
ECM 630 13 C L Electronic Calibration Code In-
compatibility - Out of Calibration
ECM 630 31 C E ECM Program Memory (RAM)
Corruption - Condition Exists
ECM 630 31 C L ECM Program Memory (RAM)
Corruption - Condition Exists
ECM 630 12 C F Engine Control Module - Warn-
ing Software error
ECM 630 2 C F Calibration Memory : Engine
Control Module data lost - Data
Erratic, Intermittent, or Incorrect
ECM 630 2 P E Calibration Memory: Erratic, In-
termittent, or Incorrect
continued..........
100
7 SPN 6~