User Manual
7 SPN 6~
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
TCU 6 * * E Short circuit in travel boost sole-
noid system
TCU 60 * * L ADDITIONAL BRAKE STATUS
SIGNAL
TCU 60 * * F ADDITIONAL BRAKE STATUS
SIGNAL
ECM 608 2 C F SAE J1587/J1922 data link -
can not transmit. Communica-
tion between the ECM and an-
other device on the J1587/
J1922 data link has been lost.
ECM 608 9 C F Data Communication error over
the J1587 data link Circuit
ECM 609 2 C F Engine Control Module Identifi-
cation Input State Error
ECM 609 2(J1587) C F Error detected in the control
synchronization of multiple en-
gines.
TCU 61 * * L AEB REQUEST SIGNAL
TCU 61 * * F AEB REQUEST SIGNAL
ECM 611 15 C F Turbocharger compressor outlet
temperature - data above nor-
mal. High turbocharger com-
pressor outlet temperature has
been calculated by the ECM.
ECM 611 2 C F Auxiliary Intermediate (PTO)
Speed Switch Validation - Data
Erratic, Intermittent, or Incorrect.
The position of the intermediate
speed control switch 1 does not
match the position of the inter-
mediate speed control validation
switch.
ECM
611 31 C F Engine Control Module Data
Lost - Condition Exits. Severe
loss of data from the ECM.
ECM 611 4 C F Post-Filter Oil Pressure Sensor
Circuit- Shorted Low
ECM 611 16 C E Fuel Inlet Meter Device - Data
Valid but Above Normal Opera-
tional Range - Moderately Se-
vere Level
ECM 611 16 C L Fuel Inlet Meter Device - Data
Valid but Above Normal Opera-
tional Range - Moderately Se-
vere Level
ECM 611 18 C E Fuel Inlet Meter Device flow de-
mand lower than expected - Da-
ta Valid but Below Normal Op-
erational Range - Moderately
Severe Level
ECM 611 18 C L Fuel Inlet Meter Device flow de-
mand lower than expected - Da-
ta Valid but Below Normal Op-
erational Range - Moderately
Severe Level
ECM 611 31 C E Operator Interface Mode Transi-
tion to Emergency Stop (Due to
E-Stop) - Condition Exists
ECM 611 31 C L Operator Interface Mode Transi-
tion to Emergency Stop (Due to
E-Stop) - Condition Exists
ECM 611 2 C E Auxiliary Intermediate (PTO)
Speed Switch Validation - Data
erratic, intermittent or incorrect
ECM 611 2 C L Auxiliary Intermediate (PTO)
Speed Switch Validation - Data
erratic, intermittent or incorrect
ECM 611 3 C F High voltage detected at the
alarm circuit when low voltage
was expected by the ECM.
ECM 611 7 C F Autoshift failure, at least three
shift attempts were missed.
continued..........
...........continued
TYPE SPN FMI
En-
gine
Ma-
chine
type
Description
ECM 611 16 C F Fuel Inlet Meter Device : Fuel
Inlet Meter Device - Data Valid
but Above Normal Operational
Range - Moderately Severe
Level
ECM 611 18 C F Fuel Inlet Meter Device : Fuel
Inlet Meter Device flow demand
lower than expected - Data Val-
id but Below Normal Operational
Range - Moderately Severe
Level
ECM
612 2 C F Engine Speed/Position Sensor
Circuit lost both of two signals
from the magnetic pickup sen-
sor - Data Erratic, Intermittent,
or incorrect
ECM 612 2 C E Engine Magnetic Speed/Posi-
tion Lost Both of Two Signals -
Data erratic, intermittent or in-
correct
ECM 612 2 C L Engine Magnetic Speed/Posi-
tion Lost Both of Two Signals -
Data erratic, intermittent or in-
correct
ECM 612 3 C F High voltage detected at the
ICON lamp circuit when low
voltage was expected by the
ECM.
ECM 612 4 C F Less than 6 VDC (low voltage)
detected at the ICON lamp cir-
cuit when high voltage was ex-
pected by the ECM.
ECM 613 14 C F OEM Component Failure
ECM 613 31 C F
ECM 614 2 C F
ECM 615 31 C F Incorrect voltage detected at the
ICON starter relay/Interlock Cir-
cuit input circuit by the ECM.
TCU 62 * * L PTO TORQUE SIGNAL
TCU 62 * * F PTO TORQUE SIGNAL
ECM 620 1 C F
ECM 620 18 C F OEM Sensor Supply Voltage
Low - Warning
ECM 620 3 C F High voltage detected on the in-
ternal electronic control module
(ECM) supply wire to the sen-
sors.
ECM 620 4 C F Low voltage detected on the in-
ternal electronic control module
(ECM) supply line to some of
the sensors.
ECM 623 4 C E Red Stop Lamp Driver Circuit -
Voltage Below Normal, or Shor-
ted to Low Source
ECM 623 4 C L Red Stop Lamp Driver Circuit -
Voltage Below Normal, or Shor-
ted to Low Source
ECM 623 5 P E Red Stop Lamp : Current Below
Normal
ECM 623 5 P L Red Stop Lamp : Current Below
Normal
ECM 623 6 P E Red Stop Lamp : Current Above
Normal
ECM 623 6 P L Red Stop Lamp : Current Above
Normal
ECM 623 4 C F Red Stop Lamp : Red Stop
Lamp Driver Circuit - Voltage
Below Normal, or Shorted to
Low Source
ECM 623464 13 Y E Injector (No. 3 cylinder) correc-
tion value error
ECM 623464 13 Y L Injector (No. 3 cylinder) correc-
tion value error
continued..........
99
7 SPN 6~