User Manual

GENERAL EM -9
TIGHTENING TORQUE
Items (diameter × length)
Screw size
O.D×pitch
(mm)
Nm kgf.m Ib-ft
Main bear ing cap bolt M14×2.0
49+90 5.0+90 36.4+90
Front plate flange bolt(8 ×16)
―
18.6~27.4 1.9~2.8 13.8~20.4
Rear oil seal s lin ger flange bolt(6×12)
―
7.8~11.8 0.8~1.2 5.8~8.7
Supply pump side timing gear case
mounting bolt
―
18.6~27.4 1.9~2.8 13.8~20.4
Supply pump flange bolt
―
16.7~25.5 1.7~2.6 12.4~18.9
Oil jet check valve M12×1.25
29.4 3.0 21.8
Rear plate flange bolt(10×22) M10×1.5
63.7 6.5 47.3
Rear st iffener bracket flange bolt(8 ×55)
―
18.6~27.4 1.9~2.8 13.8~20.4
Rear stiffener bracket flang e bolt (10×90)
―
38.2~58.8 3.9~6.0 28.4~43.6
Engine mounting bracket mounting bolt
―
32.3~49 3.3~5.0 24~36.4
Cylinder
block
Crankcase oil line set screw M10×1.5
24.5 2.5 18.2
Oil strainer flange bolt(8 ×16)
―
18.6~27.4 1.9~2.8 13.8~20.4
Oil strainer flange bolt (8 ×40)
―
18.6~27.4 1.9~2.8 13.8~20.4
Oil pan mounting flange bolt (8×12) M8×1.2
18.6~27.4 1.9~2.8 13.8~20.4
Oil level gauge mounting flange bolt(8×16)
―
18.6~27.4 1.9~2.8 13.8~20.4
Oil pan drain plug M14×1.5
34.3~39.2 3.5~4.0 25.4~29.1
Oil filter element M26×1.5
19.6 2.0 14.5
Oil cooler by-pass M16×1.5
19.6 2.0 14.5
Oil cooler relief valve M16×1.5
19.6 2.0 14.5
Oil cooler drain plug M14×1.5
34.3 3.5 25.4
Oil cooler mounting flange bolt
―
18.6~27.4 1.9~2.8 13.8~20.4
Oil line flange bolt
―
7.8~11.8 0.8~1.2 5.8~8.7
Oil lin e eyebolt
―
18.6~22.5 1.9~2.3 13.8~16.7
Idler g ear oil supply pipe
―
18.6~22.5 1.9~2.3 13.8~16.7
Turbo charger oil pipe eyebolt
―
18.6~22.5 1.9~2.3 13.8~16.7
Lubrication
system
Turbo charger oil pipe flange bolt(8×16)
―
18.6~27.4 1.9~2.8 13.8~20.4
Oil pump Oil pump mounting flange bolt(8 ×55)
―
18.6~27.4 1.9~2.8 13.8~20.4
Cylinder head mounting bolt M14×2.0
147+90 15.0 +9 0 109+90
Cylinderheadstud(10×25)
―
34.3 3.5 25.4
Cylinder
head
Cylinderheadstud(10×48)
―
34.3 3.5 25.4