User's Manual
Table Of Contents
- 1 Notes on the document
- 2 Safety regulations
- 3 Product description
- 3.1 Constituents
- 3.1.1 Voltage supply and alarming system
- 3.1.1.1 Terminal block
- 3.1.1.2 Expansion for VAC voltage supply (VAC voltage supply unit)
- 3.1.1.3 Alarm system expansion
- 3.1.1.4 SC200 - optional (VAC or alarm system expansion)
- 3.1.1.5 Alarm input/output module - optional (VAC or alarm system expansion)
- 3.1.1.6 Rectifier module - optional (VAC expansion)
- 3.1.2 E1 connection board
- 3.1.3 Redundancy package with LAN Routing Unit (LRU)
- 3.1.4 On/off switch
- 3.1.5 TIB transceiver module (TETRA Indoor Base)
- 3.1.6 Antenna Coupling System (ACS)
- 3.1.7 Fan unit
- 3.1.8 Cavity coupler (only for the Cavity variant)
- 3.1.9 Redundancy options for the DIB-500 R4.1 or the Base Station Function (BSF)
- 3.1.1 Voltage supply and alarming system
- 3.2 Interfaces
- 3.3 Wiring diagrams
- 3.4 Scope of delivery
- 3.1 Constituents
- 4 Transport and storage
- 5 Setup and commissioning
- 5.1 Safety measures and prerequisites
- 5.2 Tools, aids and materials
- 5.3 Installing equipment racks
- 5.4 Removing the top cover of the mounting frame
- 5.5 Connecting equipment racks (as of 5 carriers)
- 5.6 Connection to the electrical system
- 5.7 Connecting Ethernet cables
- 5.8 Installing the GPS antenna
- 5.9 Installing the GPS protector - optional
- 5.10 Connecting antennas
- 5.11 Connecting external alarm sensors (LSA+)
- 5.12 Connecting external alarms - optional, with VAC or alerting expansion
- 5.13 Mounting the top cover of the equipment rack
- 5.14 Switching on the voltage source
- 5.15 Switching on the DIB-500 R4.1
- 6 Configuration
- 6.1 Configuring the software
- 6.1.1 Work equipment
- 6.1.2 Preparatory measures
- 6.1.3 Deleting the ARP buffer
- 6.1.4 Configuring and generating network configurations via the NMC-515 ConfigurationManager
- 6.1.5 Creating the download repository
- 6.1.6 Adapting IP addresses (with more than one transceiver module)
- 6.1.7 Performing an initial download via NMC-522 DownloadManager
- 6.2 Adjusting a cavity coupler - optional (cavity variant only)
- 6.3 Concluding tasks
- 6.1 Configuring the software
- 7 Function tests and operating surveillance
- 8 Service interruption
- 9 Recommissioning
- 10 Maintenance
- 11 Component replacement
- 11.1 Safety measures and prerequisites
- 11.2 Overview of replacement components and tools, aids and materials
- 11.2.1 Replacing the TIB transceiver module (tools and aids)
- 11.2.2 Replacing the ACS (tools and aids)
- 11.2.3 Replacing components of the fan unit (tools, aids and materials)
- 11.2.4 Replacing the LRU (tools and aids)
- 11.2.5 Replacing the top hat rail power supply unit (tools and aids)
- 11.2.6 Replacing components of the mounting frame/the voltage supply unit (tools, aids and materials)
- 11.2.7 Replacing cavity couplers (tools and aids)
- 11.2.8 Replacing the GPS protector (tools and aids)
- 11.3 Replacing the TIB
- 11.4 Replacing the ACS
- 11.5 Replacing fan unit constituents
- 11.6 Replacing the LRU - optional (redundancy package)
- 11.7 Replacing the top hat rail - optional (redundancy package)
- 11.8 Replacing components of the VAC and alarm system expansion - optional
- 11.9 Replacing cavity couplers - optional (cavity variants only)
- 11.10 Replacing the GPS protector - optional
DIB-500 R4.1 Function tests and operating surveillance
Function tests and operating surveillance GPS
160 Installation, Operation and Service Manual 90DIB500R41IM_FCC02 – 99.1
All the network constituents of an ACCESSNET
®
-T IP network are monitored via the
NMC-511 FaultManager. Operational states and faults are detected by the network
management system and visualized via all the connected workstations with the
NMC-511 FaultManager installed and enabled.
The NMC-511 FaultManager displays the operational states and faults in an alarm sta-
tus list based on the corresponding network element in the respective network infra-
structure. This makes permanent network monitoring possible.
The procedures for this purpose are described in corresponding documents, refer to
Table 7.9.
In the NMC-511 FaultManager the operating conditions and errors on network compo-
nents are represented by so-called alarm objects.
Alarm objects furnish alarms/statuses for properties of hardware and software compo-
nents. In addition, alarm objects contain information that aids in the context of fault man-
agement in the evaluation, localisation and removal of errors.
Output via command line (shell)
In addition to the NMC-511 FaultManager, the messages can also be visualised via the
shell of the PUC software component. This requires especially trained technical person-
nel with "Service Level 3".
If you have any questions on this topic, please revert to your responsible service repre-
sentative.
Table 7.10 describes the possible messages of the GPS module.
Table 7.9 Required product documents
Product Document type
NMC-511 FaultManager User Manual
Table 7.10 GPS module – Possible messages
No. Alarm object (NMC-511 FaultMan-
ager)
Message (PUC shell) Description
1 GPS module | Synchronisation signal GPS_STATUS_1PPS_GPS_ERROR_E
VP
No or insufficient GPS
satellite reception
2 GPS antenna | Satellite reception GPS_SATELLITE_CONTACT_ERROR
_EVP
3 GPS module | NMEA interface GPS_STATUS_NMEA_ERROR_EVP No GPS receiver data
4 GPS antenna | Voltage supply GPS_STATUS_ANTENNA_ERROR_EV
P
Malfunction of the volt-
age supply in the TIB
transceiver module
5 GPS module | Voltage supply GPS_STATUS_HW_MODULE_ERROR_
EVP