User's Manual
Table Of Contents
- 1 Notes on the document
- 2 Safety regulations
- 3 Product description
- 3.1 Constituents
- 3.1.1 Voltage supply and alarming system
- 3.1.1.1 Terminal block
- 3.1.1.2 Expansion for VAC voltage supply (VAC voltage supply unit)
- 3.1.1.3 Alarm system expansion
- 3.1.1.4 SC200 - optional (VAC or alarm system expansion)
- 3.1.1.5 Alarm input/output module - optional (VAC or alarm system expansion)
- 3.1.1.6 Rectifier module - optional (VAC expansion)
- 3.1.2 E1 connection board
- 3.1.3 Redundancy package with LAN Routing Unit (LRU)
- 3.1.4 On/off switch
- 3.1.5 TIB transceiver module (TETRA Indoor Base)
- 3.1.6 Antenna Coupling System (ACS)
- 3.1.7 Fan unit
- 3.1.8 Cavity coupler (only for the Cavity variant)
- 3.1.9 Redundancy options for the DIB-500 R4.1 or the Base Station Function (BSF)
- 3.1.1 Voltage supply and alarming system
- 3.2 Interfaces
- 3.3 Wiring diagrams
- 3.4 Scope of delivery
- 3.1 Constituents
- 4 Transport and storage
- 5 Setup and commissioning
- 5.1 Safety measures and prerequisites
- 5.2 Tools, aids and materials
- 5.3 Installing equipment racks
- 5.4 Removing the top cover of the mounting frame
- 5.5 Connecting equipment racks (as of 5 carriers)
- 5.6 Connection to the electrical system
- 5.7 Connecting Ethernet cables
- 5.8 Installing the GPS antenna
- 5.9 Installing the GPS protector - optional
- 5.10 Connecting antennas
- 5.11 Connecting external alarm sensors (LSA+)
- 5.12 Connecting external alarms - optional, with VAC or alerting expansion
- 5.13 Mounting the top cover of the equipment rack
- 5.14 Switching on the voltage source
- 5.15 Switching on the DIB-500 R4.1
- 6 Configuration
- 6.1 Configuring the software
- 6.1.1 Work equipment
- 6.1.2 Preparatory measures
- 6.1.3 Deleting the ARP buffer
- 6.1.4 Configuring and generating network configurations via the NMC-515 ConfigurationManager
- 6.1.5 Creating the download repository
- 6.1.6 Adapting IP addresses (with more than one transceiver module)
- 6.1.7 Performing an initial download via NMC-522 DownloadManager
- 6.2 Adjusting a cavity coupler - optional (cavity variant only)
- 6.3 Concluding tasks
- 6.1 Configuring the software
- 7 Function tests and operating surveillance
- 8 Service interruption
- 9 Recommissioning
- 10 Maintenance
- 11 Component replacement
- 11.1 Safety measures and prerequisites
- 11.2 Overview of replacement components and tools, aids and materials
- 11.2.1 Replacing the TIB transceiver module (tools and aids)
- 11.2.2 Replacing the ACS (tools and aids)
- 11.2.3 Replacing components of the fan unit (tools, aids and materials)
- 11.2.4 Replacing the LRU (tools and aids)
- 11.2.5 Replacing the top hat rail power supply unit (tools and aids)
- 11.2.6 Replacing components of the mounting frame/the voltage supply unit (tools, aids and materials)
- 11.2.7 Replacing cavity couplers (tools and aids)
- 11.2.8 Replacing the GPS protector (tools and aids)
- 11.3 Replacing the TIB
- 11.4 Replacing the ACS
- 11.5 Replacing fan unit constituents
- 11.6 Replacing the LRU - optional (redundancy package)
- 11.7 Replacing the top hat rail - optional (redundancy package)
- 11.8 Replacing components of the VAC and alarm system expansion - optional
- 11.9 Replacing cavity couplers - optional (cavity variants only)
- 11.10 Replacing the GPS protector - optional
DIB-500 R4.1 Component replacement
Replacing cavity couplers – optional (cavity variants only)
218 Installation, Operation and Service Manual 90DIB500R41IM_FCC02 – 99.1
Uninstalling the "DCTools" application
The "DCTools" application facilitates extensive configuration of the SC200. For this rea-
son, the application must be uninstalled after having configured the SC200 since it is
not needed for the functional operation.
The "DCTools" application can be uninstalled via "Add or Remove Programs" in the
Windows Control Panel.
Proceed as follows to uninstall the "DCTools" application:
Preparation:
✓ The installation of the SC200 must have been completed.
✓ Administrator rights must have been granted for the respective installation direc-
tory.
Carry out the following steps:
1. Start the Windows Control Panel via the Windows Start Menu > Settings > Control
Panel > Software.
2. Select the "DCTools" application in the list of installed programs and click the
"Remove" button to uninstall the application.
➥ The Select Uninstall Method dialogue opens.
3. Ensure that Automatic has been selected and proceed according to the instructions
of the Setup wizard.
✓ You have successfully completed the uninstall process.
11.9 Replacing cavity couplers – optional (cavity variants
only)
Depending on the number of carriers, up to two equipment cabinets are used for the
DIB-500 R4.1 in the cavity variant. The cavity couplers (one per carrier) are installed in
the respective equipment cabinet(s) of the DIB-500 R4.1. With more than four carriers,
the equipment racks are positioned next to each other on site and connected with each
other.
The tasks listed in the following table must be performed for the replacement of a cavity
coupler.
Table 11.34 Overview of the tasks to be performed (Replacing cavity couplers – optional (cavity vari-
ants only))
Tasks/work steps Described in
Temporary service interruption Section 8.1 on
page 163
Replacing a cavity coupler Section 11.3.1 on
page 177
Adjusting a cavity coupler – optional (cavity variant only) Section 6.2 on
page 143
Recommissioning after a temporary service interruption Section 9.1 on
page 167