User's Manual
Table Of Contents
- 1 Notes on the document
- 2 Safety regulations
- 3 Product description
- 3.1 Constituents
- 3.1.1 Voltage supply and alarming system
- 3.1.1.1 Terminal block
- 3.1.1.2 Expansion for VAC voltage supply (VAC voltage supply unit)
- 3.1.1.3 Alarm system expansion
- 3.1.1.4 SC200 - optional (VAC or alarm system expansion)
- 3.1.1.5 Alarm input/output module - optional (VAC or alarm system expansion)
- 3.1.1.6 Rectifier module - optional (VAC expansion)
- 3.1.2 E1 connection board
- 3.1.3 Redundancy package with LAN Routing Unit (LRU)
- 3.1.4 On/off switch
- 3.1.5 TIB transceiver module (TETRA Indoor Base)
- 3.1.6 Antenna Coupling System (ACS)
- 3.1.7 Fan unit
- 3.1.8 Cavity coupler (only for the Cavity variant)
- 3.1.9 Redundancy options for the DIB-500 R4.1 or the Base Station Function (BSF)
- 3.1.1 Voltage supply and alarming system
- 3.2 Interfaces
- 3.3 Wiring diagrams
- 3.4 Scope of delivery
- 3.1 Constituents
- 4 Transport and storage
- 5 Setup and commissioning
- 5.1 Safety measures and prerequisites
- 5.2 Tools, aids and materials
- 5.3 Installing equipment racks
- 5.4 Removing the top cover of the mounting frame
- 5.5 Connecting equipment racks (as of 5 carriers)
- 5.6 Connection to the electrical system
- 5.7 Connecting Ethernet cables
- 5.8 Installing the GPS antenna
- 5.9 Installing the GPS protector - optional
- 5.10 Connecting antennas
- 5.11 Connecting external alarm sensors (LSA+)
- 5.12 Connecting external alarms - optional, with VAC or alerting expansion
- 5.13 Mounting the top cover of the equipment rack
- 5.14 Switching on the voltage source
- 5.15 Switching on the DIB-500 R4.1
- 6 Configuration
- 6.1 Configuring the software
- 6.1.1 Work equipment
- 6.1.2 Preparatory measures
- 6.1.3 Deleting the ARP buffer
- 6.1.4 Configuring and generating network configurations via the NMC-515 ConfigurationManager
- 6.1.5 Creating the download repository
- 6.1.6 Adapting IP addresses (with more than one transceiver module)
- 6.1.7 Performing an initial download via NMC-522 DownloadManager
- 6.2 Adjusting a cavity coupler - optional (cavity variant only)
- 6.3 Concluding tasks
- 6.1 Configuring the software
- 7 Function tests and operating surveillance
- 8 Service interruption
- 9 Recommissioning
- 10 Maintenance
- 11 Component replacement
- 11.1 Safety measures and prerequisites
- 11.2 Overview of replacement components and tools, aids and materials
- 11.2.1 Replacing the TIB transceiver module (tools and aids)
- 11.2.2 Replacing the ACS (tools and aids)
- 11.2.3 Replacing components of the fan unit (tools, aids and materials)
- 11.2.4 Replacing the LRU (tools and aids)
- 11.2.5 Replacing the top hat rail power supply unit (tools and aids)
- 11.2.6 Replacing components of the mounting frame/the voltage supply unit (tools, aids and materials)
- 11.2.7 Replacing cavity couplers (tools and aids)
- 11.2.8 Replacing the GPS protector (tools and aids)
- 11.3 Replacing the TIB
- 11.4 Replacing the ACS
- 11.5 Replacing fan unit constituents
- 11.6 Replacing the LRU - optional (redundancy package)
- 11.7 Replacing the top hat rail - optional (redundancy package)
- 11.8 Replacing components of the VAC and alarm system expansion - optional
- 11.9 Replacing cavity couplers - optional (cavity variants only)
- 11.10 Replacing the GPS protector - optional
Installation, Operation and Service Manual 90DIB500R41IM_FCC02 – 99.1 135
DIB-500 R4.1 Configuration
Configuring the software
6.1.5 Creating the download repository
For commissioning network elements locally via the NMC-522 DownloadManager, the
Download Repository must be created on the service computer. For this purpose, the
required directory structures must be stored on the service computer.
The procedures for this purpose are described in corresponding documents, refer to
Table 6.6.
6.1.6 Adapting IP addresses (with more than one transceiver module)
If a base station with multiple transceiver modules is used, the IP addresses of these
hardware components must be adapted.
The following work steps are required for this purpose:
| Adapting the IP addresses (IntelPC)
| Adapting the IP addresses (PowerPC)
6.1.6.1 Adapting the IP addresses (IntelPC)
The IP addresses of the hardware components are identical after the respective plat-
form image has been loaded. When hardware components are delivered, the platform
images have already been loaded. For the initial download via the NMC-522 Download-
Manager, however, the corresponding hardware components must feature a unique IP
address.
Table 6.7 describes the standard IP address that is assigned while loading the platform
image of a transceiver module.
If a base station with multiple transceiver modules is used, the IP addresses of all addi-
tional transceiver modules must be adapted. Otherwise it will not be possible to access
the respective transceiver module(s).
Table 6.8 describes the IP scheme by which the IP addresses of the transceiver mod-
ules must be assigned.
Table 6.6 Required product documents
Product Document type
Service computer Configuration Manual
Table 6.7 Standard IP addresses of the transceiver modules
Standard IP address
10.255.255.1
Table 6.8 Transceiver module IP addressing scheme (IntelPC)
First
transceiver module
Second
transceiver module
Third
transceiver module
Fourth
transceiver module
10.255.255.1 10.255.255.2 10.255.255.3 10.255.255.4