Users Manual

ManualsBrandsHytera Communications ManualsElectronicsDIGITAL PORTABLE RADIO





Checking the Battery Power

To check the battery power, press the preprogrammed Battery Power

Indicator key. The following table lists the battery power indications.

LED

Indicator

Alert Tone

Battery Power

Glows green

Three beeps

High

Glows orange

Two beeps

Medium

Glows red

One beep

Low

Glows red

Low battery tone

Below the low battery

threshold. Recharge or

replace the battery.

Selecting a Zone

A zone is a group of channels within the same operational area. The radio

supports up to 3 zones, each of which contains up to 16 channels.

To select a zone, press the preprogrammed Zone Up or Zone Down key.

Selecting a Channel

To select a channel, rotate the Channel Selector knob.

If the Channel Notify feature is enabled, the radio automatically announces

the current channel upon power-on and channel change.

Call Services

Calls on Digital Channel

You can initiate or receive the following types of calls on a digital channel:

 Private call: a call from an individual user to another individual user.

 Group call: a call from an individual user in a group to all the other

members in the group.

 All call (enabled by your dealer): a call from an individual user to all

other users on the current channel.

Initiating a Call

You can initiate a call in either of the following ways:

 On the home screen, press and hold the PTT key to initiate a

private/group/all call to the preset contact on the channel.

 If the One Touch Call feature is configured by your dealer, press the

preprogrammed One Touch Call key, and then press the PTT key to

initiate a call to a private or group contact.

Receiving and Responding to a Call

You can receive a call without any operation.

To respond to a call, press and hold the PTT key within the preset time.

Ending a Call

 A private or group call automatically ends when the call hang time

expires.

 An all call ends when the calling party releases the PTT key.

Calls on Analog Channel (Without Signaling)

You can initial a call to all other users on the current analog channel. The

            

190335437 





 !"#$%&'(

#)*! +(, -,P.R.C,P 518057

Summary of content (8 pages)

PAGE 1
! " # $ %&' ( # ) * ! + ( , - ,P.R.
PAGE 2
LED Indications Product Overview LED Indicator Product Layout - Programmable Keys For enhanced convenience, you can request your dealer to program SK1 and SK2 as shortcuts to radio features. For details, consult your dealer. 1 Radio Status Flashes green The radio is being turned on. Glows green The radio is receiving. Glows red The radio is transmitting. Flashes orange slowly The radio is scanning. Glows orange Call hang time: No voice is being transmitted or received during a call.
PAGE 3
Turning the Radio On or Off Basic Operations Charging the Battery CAUTION •• Read the Safety Information Booklet before charging. •• Use the approved charger to charge the battery. •• The remaining lithium-ion battery power is limited to 30% pursuant to the new lithium battery shipment regulation approved by International Air Transport Association (IATA). Before initial use, charge the battery. You can charge either the standalone battery or the radio with battery attached.
PAGE 4
Checking the Battery Power Call Services Call on Digital Channel To check the battery power, press the preprogrammed Battery Power Indicator key. The following table lists the battery power indications. LED Indicator Alert Tone You can initiate or receive the following types of calls on a digital channel: Battery Power Glows green Three beeps High Glows orange Glows red Two beeps One beep Medium Low Glows red Low battery tone Below the low battery threshold. Recharge or replace the battery.
PAGE 5
Call on Analog Channel (Without Signaling) You can initial a call to all other users on the current analog channel. The operations are the same as those on a digital channel. For details on more features and operations, please visit our website at: http://www.hytera.com, or scan the QR code to download the User Manual .
PAGE 6
FCC/ISEDC Statement This device complies with part 15 of the FCC/ISEDC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la partie 15 des règles FCC/ISEDC.
PAGE 7
RF Exposure Compliance and Control Guidelines and Operating Instructions  To control your exposure and ensure compliance with the  occupational/controlled environmental exposure limits, Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines. Contact your local dealer for the optional accessories of the product. always adhere to the following procedures. Guidelines:  Do not remove the RF Exposure Label from the device.
PAGE 8
SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value.