AQ85000G 8 * VOLT MAX LITHIUM-ION CORDLESS ROTARY TOOL WITH 40PCS ACCESSORIES Electronic Version of this Manual Available on Walmart.com * Maximum initial battery voltage (measured without load) is 8 volts. Normal voltage is 7.2.
Contents Overview ....................................................................................... 3 Workplace ..................................................................................... 4 Electrical safety ........................................................................... 4-7 Personal safety .................................................................... 5 Power tool use and care ...................................................... 6 Additional safety rule .........
8.0v Max Lithium-ion Cordless Rotary Tool Overview Overview A. Collet nut B. LED light C. Shaft lock button D. On/off button E. Speed control buttons F. Charging socket G. Battery charging light H. Speed indicator lights I. Power supply F G E D H C I B Figure 1 A Please read before returning this product for any reason: If you have questions or experience a problem with your Hyper Tough purchase, call 1-800-840-7856 from 8:00 a.m. to 8:00 p.m. Eastern Standard Time, Monday through Friday.
8.0v Max Lithium-ion Cordless Rotary Tool Workplace/Electrical safety Hyper Tough; 4 Remember To Recycle Customer Service 8:00AM-8:00PM(EST), Monday - Friday 1-800-840-7856 acs@americancustomerservice.
8.0v Max Lithium-ion Cordless Rotary Tool Electrical and Personal Safety h) Do not run cordless rotary tool while holding on your side. A spinning rotary tool accessory could become entangled with clothing and injury may result. 5 Remember To Recycle Customer Service 8:00AM-8:00PM(EST), Monday - Friday 1-800-840-7856 acs@americancustomerservice.
8.0v Max Lithium-ion Cordless Rotary Tool 6 Remember To Recycle Use and Care Customer Service 8:00AM-8:00PM(EST), Monday - Friday 1-800-840-7856 acs@americancustomerservice.
8.0v Max Lithium-ion Cordless Rotary Tool Additional Safety Rule handles if that If tools 7 Remember To Recycle Customer Service 8:00AM-8:00PM(EST), Monday - Friday 1-800-840-7856 acs@americancustomerservice.
.0v Max Lithium-ion Cordless Rotary Tool Symbols WARNING: FCC Part 15 marking and instruction Marking shall include: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
8.0v Max Lithium-ion Cordless Rotary Tool Rotary Tool Safety SAFETY RULES FOR ROTARY TOOLS 1. This power tool is intended to function as a grinder, sander, wire brush, or polisher. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 2. Use as intended only.
8.0v Max Lithium-ion Cordless Rotary Tool Rotary Tool Safety 12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 13. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 14. Do not operate the power tool near flammable materials. Sparks could ignite these materials.
8.0v Max Lithium-ion Cordless Rotary Tool Rotary Tool Safety/Charging 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
8.0v Max Lithium-ion Cordless Rotary Tool Charging/Operation C. In case the battery liquid gets in your eyes, flush your eyes with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: the liquid is a 25-35% solution of potassium hydroxide. Chargers are designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any other voltage. BEFORE ATTEMPTING TO CHARGE YOUR ROTARY TOOL, THOROUGHLY READ ALL THE SAFETY INSTRUCTIONS. • The rotary tool is not fully charged.
8.0v Max Lithium-ion Cordless Rotary Tool Change accessories by inserting the new one into the collet as far as possible to minimize run out and unbalance. With the shaft lock engaged, finger tighten the collet nut until the accessory shank is gripped by the collet. Using wrench, completely tighten to fully secure the accessory. NOTE: Avoid excessive tightening of the collet nut when there is no bit inserted.
8.0v Max Lithium-ion Cordless Rotary Tool Operation/Using Accessory Speed Setting Speed Range the felt polishing accessories. They may also be best for working on delicate projects, delicate 5 5,000 RPM wood carving and fragile model parts. All brushing applications require lower speeds 10 10,000 RPM to avoid wire discharge from the holder. 15 15,000 RPM Higher speeds are better for carving, cutting, shaping, and cutting dadoes or rabbets in wood.
8.0v Max Lithium-ion Cordless Rotary Tool Using Accessory For best results wire brushes should be used at speeds not greater than15,000 RPM. Refer to operating speeds section for proper tool speed setting. The three shapes come in three different materials: stainless steel, brass and carbon wire. The stainless steel perform well on pewter, aluminum, stainless steel, and other metals, without leaving “after-rust”. Brass brushes are non-sparking, and softer than steel; making them.
8.0v Max Lithium-ion Cordless Rotary Tool Using Accessory HOW TO ATTACH SANDING ,GRINDING,CUTTING. Using the sanding & cutting mandrel This mandrel has a small set screw at its tip and is used with cutting wheels and sanding discs. Higher speeds, usually maximum, are best when using these types of accessories. Using the drum sander To replace a band on the drum sander, loosen the screw without removing it to contract the drum. Slide the old band off & slide the new band on.
8.0v Max Lithium-ion Cordless Rotary Tool Maintenance/Recycling MAINTENANCE Keep the tool clean using a soft damp (not wet) cloth. Do not use solvents on the plastic parts. Lubrication is not necessary. WARNING: To avoid accidents, always be sure the tool is turned “OFF” before cleaning. Protect the tool and its parts and accessories from moisture and humidity. To maintain the best performance of your rechargeable battery, protect it from overheating, both from overcharging and during storage.
8.0v Max Lithium-ion Cordless Rotary Tool Warranty ACCESSORIES If you need accessories for use with your tool, most recommended accessories are available from your local retailer. If you need accessory information, please call 1-800-840-7856. 2-YEAR LIMITED WARRANTY For 2 years from the date of purchase, this product is warranted for the original purchaser to be free from defects in materials and workmanship through normal use.
8.
