HYPE R AQ76008G TOUGH 20V MAX CHARGE LITHIUM-ION GODLESS IMPACT DRIVER INSTRUCTION MANUAL Maximum initial battery voltage (measured without load) 1s 20 Volts. Nominal voltage is 18. Electronic Version of this Manual Available on Walmart.
R Overview., Work area safety.. Electric safety. Personal safety. Power tool use and car Battery/Service/Safety.. Additional safety rules. Symbolical Operation, Troubleshooting & Maintenance. Recycling/Specifications. Specification. Warranty. CALIFORNIA PROP 65 WARNING * Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
20V. Max Cordless Impact Driver Overview A, Chuck Sleeve Fast Load Chuck C. Varlable Speed Trigger Switch D. Led Work Light E. Battery Lock Button F. Forward / Neutral / Reverse Switch G. Soft Grip H. Built-in #2 Phillips Bit 1, Battery Pack J. Battery Charger Please read before resuming this product for any reason: If you have question or experience a problem with your Hyper Tough purchase, call 1-800-840-7856 from 8:00 a.m. to 8:00 p.m. Eastern Standard Time, Monday through Friday.
20V. Max Cordless Impact Driver Workplace/Electrical Safety SAVE THESE WARNINGS AND INSTRUCTIONS 'YOU MAY NEED TO REFER TO THEM LATER The term “power too!” in the WARNING refers to your AC power (corded) power too or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such sin the presence of flammable liquids, gases or dust.
20V. Max Cordless Impact Driver Personal safety/Power tool use and care PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 2. Use personal protective equipment. Always wear eye protection.
20V. Max Cordless Impact Driver Battery/Service/Safety accidents are caused by poorly maintained power tools. 6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
20V. Max Cordless Impact Driver Additional safety rules WARNING: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This limits are designed to provide reasonable protection against harmful interference in a residential installation.
Symbols 7. Watch what you are doing and use common sense. Don’t operate any tool when you are tired. ADDITIONAL SAFETY INFORMATION WARNING: Dust from use of this tool on construction material may cause serious and/or permanent respiratory {or other) injury. Direct the particles away from your face, and be sure to use HIGASHIOSAKA approved respiratory protection against dust exposure. WARNING: ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: 1. ANSI Z87.1 eye protection (CANCAN 294.3) 2, ANSI| $12.6 (53.
20V. Max Cordless Impact Driver Operation BEFORE ATTEMPTING TO CHARGE YOUR BATTERY PACK, THOROUGHLY READ ALL THE SAFETY INSTRUCTIONS. CAUTION: *The battery s not fully charged. Before first use, the battery pack requires 5-7 hours charge time to b fully charged. Subsequent recharging needs 3-4 hours for the battery to be fully charged.
20V. Max Cordless Impact Driver Operation TOOL / BATTERY PROTECTION SYSTEM The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions: OVERLOAD PROTECTION When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication.
20V. Max Cordless Impact Driver Operation SWITCH TRIGGER To turn the tool ON, depress the switch trigger. To turn it OFF, release the switch trigger. VARIABLE SPEED The switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. NOTE: You might hear a whistling or ringing noise from the switch during use. Do not be concerned. This is a normal part of the switch function.
20V. Max Cordless Impact Driver Troubleshooting & Maintenance TROUBLESHOOTING Probity Fossils Gauss Likely Solutions Too willnotstart.| « Battery Pack not * Ra move Battery Pack, make sirs properly connected. theta are no obstructions, reinsert the. Battery Pack according ko It saps (it should only it one way), and press filmy unl the Battery Pack locks in claps. * Battery Pack not * Make mra Charger I connected and pearly charged. ‘operating property. Give sough time for Battery Pack ta recharge property.
20V. Max Cordless Impact Driver Recycling/Specifications ». THE RBRC™ SEAL The RBRC™ SEAL (Rechargeable Battery Recycling corporation) on the lithium-ion battery (or battery pack) indicates that the cost of recycling the battery or battery pack have already been paid by Hyper Tough. In some areas iris illegal to place spent lithium-ion batteries in the trash or municipal solid waste stream and the CURB program provides an environmentally conscious alternative.
20V. Max Cordless Impact Driver Specifications/Warranty . Machine Weight: « Chuck size: 1/4° quick release chuck «No Load Speed: 0-2700 RPM .Impact rate: 0-3800 IPM . Max torque: 155 Nm /1375 in-lbs.
