Instruction manual Dear Customer, Instruction manual We are pleased that you have chosen a motorhome from HYMER and would like to thank you for the trust you have shown in our company. This instruction manual is intended to help you get to know and use your new (motor)home. It is essential that you read and comply with the safety instructions in chapter 2. Don't hesitate to contact our HYMER service centres if you have any questions.
Instruction manual CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Guarantee Guarantee Confirmation: I have today received the documents for the annual servicing intervals and the water ingress test for the stated model. Please paste the warranty stamp in here.
Guarantee Water ingress test For the water ingress test your HYMER contract partner checks the complete construction of your vehicle at all composite locations, windows, skylights, service flaps and doors for tightness. Important The performance and the exact adherence to the intervals is decisive for the continuation of the 6 year weatherproof guarantee. The water ingress test must be carried out on an annual basis. The interval may be carried out max.
Guarantee 3. Annual inspection The purchaser shall send the vehicle regularly, every year, to the vendor or to an authorised HYMER AG dealer or service centre for inspection. The purchaser shall bear the cost of the inspection. The first inspection must be conducted within the first year after delivery of the vehicle to the purchaser, however, latest within the first year from the date of initial registration of the vehicle.
Guarantee Inspection After each service, the inspection plan provides you with supplementary and detailed information concerning the work which has been specifically carried out on your vehicle. You receive the inspection checklist when you collect your vehicle from your HYMER contract partner. Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
Guarantee Inspection record for a motorhome or caravan Body inspection 1 Water ingress test 1 12 months after delivery Water ingress test: Paste in the inspection stamp for the 12 month check here (subject to payment).
Guarantee Inspection record for a motorhome or caravan Body inspection 3 Water ingress test 3 36 months after delivery Water ingress test: Paste in the inspection stamp for the 12 month check here (subject to payment).
Guarantee Inspection record for a motorhome or caravan Body inspection 5 Water ingress test 5 60 months after delivery Water ingress test: Paste in the inspection stamp for the 12 month check here (subject to payment).
Guarantee Inspection record for a motorhome or caravan Body inspection 8 Body inspection 9 8 years after delivery 9 years after delivery Date: Date: Mileage reading: Mileage reading: Dealer's signature and stamp: Dealer's signature and stamp: Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
Contents 1 Introduction . . . . . . . . . . . . . . . . . . 17 1.1 1.2 General . . . . . . . . . . . . . . . . . . . . . . . . 18 Environmental tips. . . . . . . . . . . . . . . . 18 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . 21 2.1 2.1.1 2.1.2 2.1.3 2.2 2.3 2.4 2.5 2.5.1 2.5.2 2.6 2.7 Fire prevention . . . . . . . . . . . . . . . . . . Avoidance of fire risks . . . . . . . . . . . . . Fire-fighting . . . . . . . . . . . . . . . . . . . . . In case of fire. . . . . . . . . . . . . . . .
Contents 6.7 6.8 6.8.1 6.8.2 6.12.3 6.12.4 Rotating seats . . . . . . . . . . . . . . . . . . . 80 Tables . . . . . . . . . . . . . . . . . . . . . . . . . 81 Suspension table with fold-out leg . . . . 81 Suspension table with separable support leg . . . . . . . . . . . . . 81 Fixed table with rigid table leg . . . . . . . 82 Suspension table with insertable table-top extension . . . . . . . 82 Lift-off table . . . . . . . . . . . . . . . . . . . . . 83 TV unit . . . . . . . . . . . . . . . . . . . . . .
Contents 10.7 10.7.1 10.7.2 10.7.3 10.7.4 10.7.5 Toilet . . . . . . . . . . . . . . . . . . . . . . . . . Swivel toilet . . . . . . . . . . . . . . . . . . . . Toilet with fixed seat . . . . . . . . . . . . . Emptying the sewage tank . . . . . . . . Winter operation . . . . . . . . . . . . . . . . Temporary lay-up . . . . . . . . . . . . . . . 11 Care. . . . . . . . . . . . . . . . . . . . . . . . . 161 11.1 11.1.1 11.1.2 External care . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . .
Contents 14 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Checklist before first journey of the vehicle Observe the following instructions before first journey of the vehicle: Checklist before first journey of the vehicle X Re-tighten the wheel nuts/wheel bolts after 50 km (30 miles). X Read the instruction manual to avoid personal and material damage. Observe the following instructions before each journey of the vehicle: X Check the tyre pressures. See Tyre pressure section. X Load the vehicle correctly. Observe the maximum permissible gross weight.
Checklist before first journey of the vehicle 16 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Introduction 1 Please read this instruction manual completely before using the vehicle for the first time! 1Introduction Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. X The non-observance of this symbol can lead to personal injury. Z The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. Z This symbol indicates recommendations or special aspects.
1 Introduction 1.1 General The vehicle is constructed in accordance with the latest technology and the recognised safety regulations. Nevertheless, personal injury may result and the vehicle may be damaged if the safety instructions in this instruction manual are not followed. Only use the vehicle in a technically impeccable condition. Follow the instructions in the instruction manual. Malfunctions which impair the safety of persons or the vehicle should be immediately remedied by qualified personnel.
Introduction 1 Z When staying in towns and communities for long periods, search for parking areas which are specially reserved for motorhomes. Enquire at the town or community authority about parking spaces. Z Always leave the parking places in a clean condition.
1 Introduction 20 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Safety 2 Chapter overview 2Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: z z z z z z z 2.1 2.1.
2 Safety z Minimum diameter of clearance = 450 mm z Maximum distance from the vehicle floor = 950 mm 2.2 General X The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (e.g. skylights with forced ventilation, mushroom-shaped vents or floor vents) are fitted to the vehicle.
Safety 2 X Before commencing the journey, open, lock and secure the shades sit- uated on the windscreen and on the driver's and front passenger's windows. X Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. During the journey, the swivel seats must remain locked in place in the direction of travel. X Before commencing the journey, store the television securely.
2 Safety Z Before commencing the journey, remove the external supports and retract the corner steadies or steady legs, which are fitted to the vehicle. Z Before commencing the journey, put the antenna in park position. Z During the initial journey and each time after changing a wheel, re-tighten the wheel bolts/wheel nuts after 50 km (30 miles). Subsequently inspect them at regular intervals in order to ensure that they are firmly seated. See chapter 13 for tightening torque.
Safety 2 X Do not use the gas cooker or gas oven for heating purposes. X If there are several gas devices, each gas device must have its own gas isolator tap. If individual gas devices are not in use, close the respective gas isolator tap. X Ignition safety valves must close within 1 minute after the gas flame has extinguished. A clicking sound is audible. Check function from time to time. X The built-in gas devices are exclusively meant for use with propane or butane gas or a mixture of both.
2 Safety X Only use special gas pressure regulators with a safety valve designed for vehicle use. Other gas pressure regulators are not permitted and cannot meet the demanding requirements. X Use the gas pressure regulator defroster if the temperature falls below 5 °C. X The designated gas bottle compartment will accommodate two gas bot- tles, i. e. Calor Gas Butane/Propane or Camping Gaz. All gas bottles must be fitted with the appropriate regulator. X Use the shortest possible tube lengths (150 cm max.
Before the journey 3 Chapter overview 3Before the journey This chapter contains important information which has to be noted before commencing your journey or carrying out any tasks before the journey.
3 Before the journey 3.2.1 Terms Z Technically speaking, the term "mass" has now replaced the term "weight". However, "weight" is still the term more frequent in common use. For better understanding, "mass" is therefore only used in the following sections for fixed formulations. Z All specifications according to EU norm DIN EN 1646-2. Maximum permissible gross weight in a laden condition The maximum permissible gross weight in a laden condition is the weight that a vehicle may never exceed.
Before the journey 3 Payload The payload is made up as follows: z Conventional load z Additional equipment z Personal equipment Z The vehicle's payload can be increased by reducing the weight in a ready- to-drive condition. To do this, it is allowed for example to empty the fluid containers or to remove the gas bottles. You will find explanations on the individual components of the payload in the following text.
3 Before the journey z Surfboards z Sports equipment For the personal equipment, according to the applicable regulations, the manufacturer must use a minimum weight that is determined according to the following formula: Formula Explanation 3.2.
Before the journey 3 To do this, proceed as follows: First only drive the vehicle on to the weighbridge with the front wheels and have it weighed. Then drive the vehicle on to the weighbridge with the back wheels and have it weighed. The individual values give the current axle loads. These are important for the correct loading of the vehicle (see section 3.2.3). The sum of these values is the current weight of the vehicle.
3 Before the journey Formulas A x G : R = weight on the rear axle Weight on the rear axle – G = weight on the front axle Explanation A G R = distance between storage compartment and front axle in cm = weight of the load in the storage compartment in kg = wheelbase of the vehicle (distance between axles) in cm Z Measure the external distances horizontally from the centre of the front wheel to the centre of the storage compartment or to the centre of the back wheel.
Before the journey 3 3.2.4 Roof load X Only climb on to the roof if a roof rail or step has been fitted. Always use the ladder at the rear to climb onto the roof. X Take care when stepping onto the ladder. There is danger of slipping when the ladder is moist or icy. X Take care when stepping onto the roof. There is danger of slipping when the roof is moist or icy. X Do not overload the roof. Road behaviour and brake reaction deteriorate as the roof load increases.
3 Before the journey Rear ladder Fig. 2 Folding downwards: Rear ladder lock Insert the key into the locking cylinder (Fig. 2,2) of the rear ladder lock (Fig. 2,1) and turn it a quarter turn until the key is in a vertical position. Hold the foldable part of the rear ladder (Fig. 2,4) and swing out the securing bracket (Fig. 2,5). Pull out the key and fold the rear ladder downwards. Folding upwards: Fold the rear ladder upwards and hold it firmly.
Before the journey 3 1 2 Fig. 3 Moving the clamping eyelets: Clamping eyelet Clamping rail Clamping eyelets rear garage Turn the clamping eyelet (Fig. 3,1) half a turn in an anticlockwise direction. Push the clamping eyelet into the clamping rail (Fig. 3,2) to the desired position. Give clamping eyelet one half turn in a clockwise direction. The clamping eyelet sits tightly in the clamping rail again. Check that the clamping eyelet is tight. 3.2.
3 Before the journey Loading the bike rack correctly: Fold the bike rack downwards. Place the heaviest bicycle directly against the rear wall. Place the lightest bicycles in the centre or on the outside of the bike rack. Secure the front and rear wheels of each bicycle with the retaining straps on the bike rack. In addition, fasten the outermost bicycle on the retaining bracket or retaining arm.
Before the journey 3 Fig. 4 Retracting: Rocker button for entrance step (entrance area) Fig. 5 Push button for entrance step (dashboard) Press the rocker switch (Fig. 4,1) in the entrance area or the push button (Fig. 5,1) on the dashboard in the driver's cabin. Extending: Press the rocker switch (Fig. 4,1) situated in the entrance area. When the engine is running and the entrance step is extended, a warning tone is heard. The warning tone ceases as soon as the entrance step is retracted. 3.
3 Before the journey Flat screen in the TV cabinet The flat screen is attached to a console in the TV cabinet. Fig. 6 Storing the television in the TV cabinet: Flat screen on jointed arm Return television into its initial position. Insert the holder for the flat screen until the latch (Fig. 6,1) locks into place. The flat screen is fastened to a jointed arm. Fig.
Before the journey 3 Move the jointed arm (Fig. 8,1) into the guide rail (Fig. 8,3) and place (Fig. 8) in the holder (Fig. 8,4). Re-tighten the knurled screws. 3.7 Sink cover X In the event of an accident or emergency braking, the sink cover (Fig. 9,1) could injure the occupants of the vehicle. Before the journey, take the sink cover off the sink and store it securely in the kitchen unit or wardrobe. Fig. 9 3.
3 Before the journey No.
Before the journey 3 Gas system Electrical system No. Checks 36 Gas bottles firmly fixed in the gas bottle compartment so that they are unable to turn 37 If the gas bottles are not connected to the gas tube, always place the protective cap on top 38 Regulator tap on the gas bottle and gas isolator taps are closed 39 Check the battery voltage of the starter and living area battery (see chapter 8).
3 Before the journey 42 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
During the journey 4 Chapter overview 4During the journey This chapter contains instructions on how to drive the motorhome. The instructions address the following topics: z z z z z z z z z z z z z z 4.
4 During the journey 4.2 Driving speed X The vehicle is equipped with a powerful engine. This means there are sufficient reserves in difficult traffic situations. This high power enables a high maximum speed and requires above-average driving ability. X The vehicle provides a large contact surface for wind. A sudden cross- wind can be especially dangerous. X Uneven or one-sided loading affects road performance.
During the journey 4 4.5 Seat belts The vehicle is equipped with seat belts in the living area on the seats for which seat belts are compulsory by law. National regulations apply seat-belt fastening. X Fasten your seat belts before the beginning of the journey and keep them fastened during the journey. X Do not damage or trap belts. Have damaged seat belts changed by an authorised specialist workshop. X Do not alter the belt fixing devices, automatic seat belt winders and the belt clips.
4 During the journey Child restraint systems are divided into five classes: Class Body weight Approximate age 0 Up to 10 kg Up to 9 months 0+ Up to 13 kg Up to 18 months I 9 kg to 18 kg 9 months to 4 years II 15 kg to 25 kg 3 years to 7 ½ years III 22 kg to 36 kg 6 years to 12 years The following illustrations show, which child restraint systems can be used on which seats. 4.7 Fig. 11 Suitable seats for child restraint systems (Integrated) Fig.
During the journey 4 4.7.1 Seats (Aguti) Fig. 13 Rotating seat into driving position Seat adjustment Fig. 14 Armrest adjustment The seats can be rotated in any direction. The seats can only be locked in position in the direction of travel. Push both armrests upward. Push the seat backwards or into the central position. Rotate the seat in the direction of travel and lock in position. Z Rotating the seats in the pitched vehicle is described in chapter 6.
4 During the journey 4.8 Headrests Z The headrests are not adjustable for all models. Fig. 15 Bench headrest Before commencing the journey, adjust the headrests (Fig. 15,1) so that the back of the head is supported at approximately ear height. Push the headrests upwards or downwards by hand. 4.9 Seating arrangement X During the journey, persons are only to sit on the permitted seats. The authorised number of seats is stipulated in the vehicle documents.
During the journey 4 Fig. 16 Opening and closing: 4.11 Switch for the electrical window winder in the driver's door Press switch (Fig. 16,1). Electrically adjustable external mirrors (Integrated) Z The main mirror of the two-part external mirror is electrically adjustable and heatable. Depending on the model, the vehicle is equipped with two electrically adjustable and heated external mirrors. The switches for external mirror adjustment and the mirror heater are on the dashboard. Fig.
4 During the journey 4.12 Roman shades for the windscreen X While driving, the Roman shade for the windscreen must be open, in a fixed position and secured. Integrated Fig. 19 Securing: Roman shade for the windscreen Use the handle (Fig. 19,2) to pull the two halves of the Roman shade for the windscreen outwards as far as they will go. Push the locking knob (Fig. 19,1) down. Partially integrated Fig. 20 Securing: Roman shade for the windscreen Fig.
During the journey 4 4.13 Roman shades for driver's window and front passenger's window X While travelling, the Roman shades for the driver's window and front passenger's window must be open, in a fixed position and secured. Integrated Fig. 22 Securing: Locking mechanism for Roman shades on driver's/front passenger's windows Use handle (Fig. 22,2) to push in the Roman shade as far as possible. Push the locking knob (Fig. 22,1) down.
4 During the journey 4.14 Writing and reading rest (Fiat base vehicle) X During the journey the writing and reading rest must be closed. Z If there is a passenger airbag, the writing and reading rest is locked so it cannot be opened. Fig. 25 4.15 Writing and reading rest (Fiat base vehicle) Bonnet X When the bonnet is open, there is a risk of injury in the engine compart- ment. X Even if the engine was switched off some time ago, it might still be hot.
During the journey 4 Opening: Pull the lever (Fig. 26,1) situated on the left-hand side of the vehicle on the dashboard. Place both hands on the top and the bottom edge of the bonnet (Fig. 27,1), do not grip the middle. Move the bonnet up. Opening (alternative): Insert key into locking cylinder on the bonnet and turn it in an anticlockwise direction. The bonnet is unlocked. Place both hands on the top and the bottom edge of the bonnet (Fig. 27,1), do not grip the middle.
4 During the journey Remove the key. Check that the cap is fastened securely on the fuel filler neck. Close the flap and press it down. 4.17 Towing X If the ignition key cannot be turned in the ignition lock, do not tow the vehicle. The steering will be locked. Z If the engine is not running or the power supply is disrupted, the servo assistance for the steering and brakes will not be operational. A considerable amount of force will be required for steering and braking.
Pitching the motorhome 5 Chapter overview 5Pitching the motorhome This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: z z z z z z z handbrake entrance step wheel chocks operation of the supports 240 V connection refrigerator retracting and extending the awning Z Pitch the vehicle so that it is as horizontal as possible. Use ramps where necessary. Otherwise, the water from the shower tray will not be able to drain properly.
5 Pitching the motorhome Z When the ground is soft, place a pad or block under the supports in order to prevent the vehicle from sinking into the ground. Z Pitch the vehicle so that it is as horizontal as possible. Otherwise, the water from the shower tray will not be able to drain properly. 5.5.2 Steady legs X The steady legs must not be used to jack up the vehicle in order to work beneath it, e.g. to change a wheel or carry out maintenance work.
Pitching the motorhome 5 Z Before commencing the journey, observe the following: Are all steady legs and support foot extensions retracted completely and secured with the splint? 5.6 240 V connection The vehicle can be connected to a 240 V power supply (see chapter 8). 5.7 Refrigerator X If the refrigerator is set to 12 V operation, it will constantly consume cur- rent.
5 Pitching the motorhome Fig. 32 Position support legs Fold out the support legs (Fig. 32,4) from the front bar (Fig. 32,1) and posi- tion them. Open the lock on the support legs. To do this, turn the catch lever (Fig. 32,2) upwards. Pull out the lower parts of the support legs (Fig. 32,3) until they reach the desired length. Close the lock on the support legs. To do this, turn the catch lever down- ward once again. Use the crank to completely extend the awning.
Living 6 Chapter overview 6Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: z z z z z z z z z z z 6.
6 Living Locking: Insert the key in the locking cylinder (Fig. 34,1) and turn it in an anticlock- wise direction until the door lock is engaged. Return the key to the central position and remove it. 6.1.2 Conversion door, inside Fig. 35 Opening: Locking: 6.1.3 Push the handle (Fig. 35,1) down. Turn the handle (Fig. 35,1) approx. 45° upward and leave it in this position. Conversion door, outside Fig.
Living 6 6.1.4 Conversion door, inside Fig. 37 Opening: Locking: 6.1.5 Pull on the handle (Fig. 37,1). The door lock is unlatched. Push the safety knob (Fig. 37,2) down. Driver's door, outside Fig. 38 Opening: Door lock of conversion door, inside Door lock of driver's door, outside Insert the key into locking cylinder (Fig. 38,2) and turn until the door lock is unlatched. Return the key to the central position and remove it. Pull on the handle (Fig. 38,1). The door is open.
6 Living 6.1.6 Driver's door, inside Fig. 39 Opening: Door lock of driver's door, inside Pull on the handle (Fig. 39,1). The door lock is unlatched. The safety knob automatically jumps out. Locking: 6.1.7 Push the safety knob in. Insect screen on the conversion door, extendable Z Open the insect screen completely before closing the conversion door. Fig. 40 Closing: Opening: 6.2 Insect screen Pull out the insect screen completely by the bar (Fig. 40,1).
Living 6 6.2.1 Flap lock, elliptical-shaped Z During rain, water can penetrate the opened flap lock. Therefore close the lock handle. Fig. 41 Opening: Flap lock, elliptical-shaped, closed Insert key into locking cylinder (Fig. 41,1) and turn one half turn in an anti- clockwise direction. The lock handle (Fig. 41,2) snaps out. Remove the key. Turn lock handle one half turn in an anticlockwise direction. The flap lock is open. Closing: Firmly close the external flap.
6 Living 6.2.2 Flap lock, elliptical-shaped (alternative) Z During rain, water can penetrate the opened flap lock. Therefore close the lock handle. Fig. 42 Opening: Flap lock, elliptical-shaped, closed Insert key into locking cylinder (Fig. 42,1) and turn a quarter turn in an anti- clockwise direction. The lock handle (Fig. 42,2) snaps out. Remove the key. Turn lock handle one quarter turn in an anticlockwise direction. The flap lock is open. Closing: Firmly close the external flap.
Living 6 6.2.3 Underfloor sliding drawer Z The maximum permitted underfloor sliding drawer load is 40 kg. Fig. 43 Opening: Retainer on the underfloor sliding drawer Open the flap lock (Fig. 43,1) as described above. Push the retainer (Fig. 43,2) down, keep it pressed and pull out the under- floor sliding drawer. 6.3 Ventilation X The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the oxygen needs to be replaced on a constant basis.
6 Living 6.4 Windows Z The windows are fitted with a blind or Roman shade and with an insect screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force. In order not to damage the tension mechanics, hold onto the blind or insect screen and allow it to slowly return to the initial position. The Roman shade and folding insect screen are made of thin woven fabric.
Living 6 Closing: 6.4.2 Close the window as far as possible and let the handle lock in place. Hinged window with automatic hinges Z Open the window completely, to release the lock. If the locking device is not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure. Z When opening the hinged windows, ensure that there are no torsional forces. Open and close the hinged windows evenly. Fig.
6 Living To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 47,3) a quarter turn towards the centre of the window. Slightly open the hinged window outwards. Return catch lever to its initial position. The locking catch (Fig. 47,2) has to be moved into the recess of window catch (Fig. 47,1). During the journey, the hinged window may not be in "continuous ventilation" position.
Living 6 6.4.4 Blind and insect screen Z Open blinds before commencing the journey. When the blinds are closed, vibrations can damage the spring shaft. The windows are fitted with a blind and an insect screen. The blind and insect screen are adjusted separately. Fig. 49 Blind Closing: Hinged window The blind is located in the upper blind box. Pull blind at the handle (Fig. 49,2) downwards. If the blind is to be com- pletely closed, it is suspended into the locking devices (Fig.
6 Living 6.4.5 Roman shade and insect screen The windows are fitted with a Roman shade and an insect screen. The Roman shade and insect screen can be adjusted separately. Fig. 50 Roman shade Closing: Hinged window The Roman shade is located in the bottom blind box. Grasp the Roman shade (Fig. 50,2) using the holding bar, pull it upwards and then release it at the desired height. The Roman shade will stay at this height.
Living 6 Closing: Grip the Roman shade (Fig. 51,2) in the centre of the holding bar, pull it out and release it at the required position. The Roman shade will stay in that position. Opening: Grip the Roman shade (Fig. 51,2) in the centre of the holding bar and slowly push it to its initial position. Insect screen The insect screen can only be operated together with the roman shade.
6 Living Driver's/front passenger's windows Fig. 53 Closing: Roman shade for the driver's and passenger's window Push the locking knob (Fig. 53,1) up. Using the handle (Fig. 53,2), draw the Roman shades for the driver's and passenger's window to the other side of the window and secure them to the magnetic strips. Opening: Use handle (Fig. 53,2) to push in the Roman shades for the driver's and passenger's window as far as possible. Push the locking knob (Fig. 53,1) down. 6.4.
Living 6 Opening: Depending on the locking system, press and hold down the locking handle (Fig. 55,1). Use the handle (Fig. 54,2 or Fig. 55,2) to pull the two halves of the Roman shade for the windscreen outwards as far as they will go. Push the locking knob (Fig. 54,1) downwards and release the locking handle (Fig. 55,1) and let it click into position. Driver's/front passenger's windows Various locking systems are built in depending on the model. Fig.
6 Living Z The skylights are fitted with a blind or Roman shade and with an insect screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force. In order not to damage the tension mechanics, hold onto the blind or insect screen and allow it to slowly return to the initial position. The Roman shade and folding insect screen are made of thin woven fabric.
Living 6 Locking in the ventilation position: Grip lever and pull hinged skylight downwards. Turn the lever one quarter turn. The latch (Fig. 58,4) must slide into the upper aperture (Fig. 58,2). Z If it rains and the hinged skylight is in ventilation position, that could lead to water penetrating the living area. Therefore close hinged skylight completely. Roman shade The Roman shade may be closed at any position, either with the hinged skylight open or closed.
6 Living Fig. 62 Ventilation position Heki skylight in ventilation position Fig. 63 Ventilation position locking mechanism The Heki skylight can be put in two ventilation positions: Bad weather position (Fig. 62,1) and central position (Fig. 62,2). Depending on the model, the skylight can be locked in the central position with the latch (Fig. 63,1). Press the safety knob (Fig. 60,2) and pull the bar (Fig. 60,1) down with both hands. Pull the bar in the guides (Fig. 61,2) to the desired position.
Living 6 Closing: Rotate the hand crank until the wind-up skylight is closed. The wind-up sky- light can be locked after rotating two or three more times. Check the locking mechanism. To do so, press your hand against the acrylic glass. Roman shade The Roman shade can be closed in any position, as desired. If the Roman shade is locked with the insect screen, the insect screen is also moved along on closing the Roman shade. Closing: Pull the handle of the Roman shade (Fig.
6 Living Opening: Press the right side of the rocker button (Fig. 65,2) on the operating unit (Fig. 65,1). Closing: Press the left side of the rocker button (Fig. 65,2) on the operating unit (Fig. 65,1). Roman shade Closing: If the Roman shade is locked with the insect screen, the insect screen is also moved along on closing the Roman shade. Take the handle of the Roman shade and pull upwards. Release the Roman shade at the desired position. The Roman shade will stay in that position.
Living 6 The elevating roof is lifted on one side. Fig. 66 Opening: Quick-action turnbuckle, open Fig. 67 Handles on the elevating roof On both sides, rotate the handle (Fig. 66,1) on the quick-action turnbuckle (Fig. 66,2) through half a turn anti-clockwise. The lock is released. The elevating roof moves up slightly and remains in this position. Press the elevating roof fully up (Fig. 67,2) using the handles. The lying surface in the elevating roof can be folded upwards.
6 Living Fig. 70 Lock Fig. 71 Quick-action turnbuckle, locked Pull down the elevating roof evenly by both handles until the elevating roof is lying on the vehicle roof. When doing this, make sure that the canvas does not get caught. On both sides, pull down the quick-action turnbuckle (Fig. 70,1) and hang it into the holding plate (Fig. 70,2) (Fig. 70). Rotate the handle (Fig. 71,1) on the quick-action turnbuckle (Fig. 71,2) through half a turn clockwise. Roll up the canvas (Fig.
Living 6 6.8 6.8.1 Tables Suspension table with fold-out leg Fig. 73 Suspension table with fold-out leg The suspension table may also be used as a bed foundation. Conversion to bed foundation: Slightly lift the front of the table-top. Unlock the table leg (Fig. 73,2) at the hinge and fold it in. Unhook the suspension table from the upper attachment rail. Attach the suspension table onto the lower attachment rail (Fig. 73,1) and rest it onto the table leg hinge (Fig. 73,3). 6.8.
6 Living Remove the table-top from the upper retainer. Hook the table-top at a 45° angle to the supports into the lower retainer (Fig. 74,3) and place on the floor with the upper part of the support leg (Fig. 74,5). 6.8.3 Fixed table with rigid table leg Fig. 75 Fixed table with rigid table leg The table-top of the fixed table of the rigid table leg can be moved both lengthways and crossways. It is not possible to convert it into a bed foundation.
Living 6 Lift the table-top slightly and push it back as far as possible. Re-tighten the knurled screws (Fig. 76,2). Reducing size: Undo the knurled screws (Fig. 76,2) at the bottom of the table. Slightly lift the front of the table-top (Fig. 77,2) and pull out. Take out the table-top extension (Fig. 77,1) and store it in the wardrobe. Lift up the front of the table-top slightly and push it all the way in. Re-tighten the knurled screws. 6.8.
6 Living 6.9 TV unit X Before commencing the journey, store the television securely. X Before commencing the journey, turn the flat screen and the screen holder back to the basic position, push them in and secure them. 6.9.1 Flat screen in the TV cabinet Positioning the flat screen The flat screen is attached to a console in the TV cabinet. Fig. 79 Flat screen in the TV cabinet Pull the release lever/handle (Fig. 79,1) forwards. Use handle to pull out as far as possible.
Living 6 Flat screen on jointed arm (alternative) The flat screen is fastened to a jointed arm. Fig. 81 Flat screen on jointed arm Loosen knurled screws (Fig. 81,2). Move the jointed arm (Fig. 81,1) upwards into the guide rails (Fig. 81,3) until the jointed arm is no longer held by the holder (Fig. 81,4). Move the flat screen to the required height and swivel it into required posi- tion. Re-tighten the knurled screws (Fig. 81,2).
6 Living 6.10 6.10.1 Beds Pull-down bed X The maximum permitted pull-down bed load is 200 kg. X The pull-down bed is not to be used for the storage of luggage. When the bed is not being used, only place the bed linen (max. 8 kg) which is required for two persons and the dinette table in it. X Before commencing the journey, secure the pull-down bed to the roof using the retaining belt. Tighten the retaining belt firmly. X Only use the pull-down bed, if the safety net is set up.
Living 6 Safety net The safety net and the retaining belts are located underneath the mattress in the pull-down bed. Only use the safety net if persons are already in the pulldown bed. Setting up: Attach the retaining belts (Fig. 82,1 or Fig. 83,1) to the hooks (Fig. 82,4 or Fig. 83,4) on the ceiling. Access ladder Always use the provided access ladder to climb up to the pull-down bed. Fig. 84 Access ladder in the receptacle In some models, the access ladder (Fig.
6 Living 6.10.2 Pull-down bed with support X Only use the pull-down bed if the access ladder (support) is hooked in correctly. X The maximum permitted pull-down bed load is 200 kg. X The pull-down bed is not to be used for the storage of luggage. When the bed is not being used, only place the bed linen (max. 8 kg) which is required for two persons and the dinette table in it. X Before commencing the journey, secure the pull-down bed to the roof using the retaining belt.
Living 6 Fig. 87 Attaching: Access ladder hooked in Fig. 88 Access ladder correctly positioned Hook the access ladder (Fig. 87,4) to the pull-down bed by attaching the two hooks (Fig. 87,1) to the holding bar (Fig. 87,3). When attaching, ensure that the ladder stiles are positioned behind the two fixtures (Fig. 87,2). This prevents lateral movement of the access ladder. Push the lower access ladder end forwards until the pull-down bed panel (Fig. 88,3) rests securely on the supports (Fig.
6 Living Fig. 89 Making ready for operation Control unit After every power interruption (e.g. lay-up over winter), the electrical drive must be made ready for operation again. To do this, proceed as follows: On the control unit (Fig. 89,3) press both arrow keys (Fig. 89,1 and 2) simultaneously and keep them pressed until the pull-down bed has moved fully down. Once the button is released, a beep sounds to confirm. Opening the pull-down bed: On the control unit (Fig.
Living 6 Fig. 90 Emergency operation Drive If the pull-down bed can no longer be moved via the control unit (e.g. due to loss of the vehicle's power supply), it can also be operated manually. To do this, proceed as follows: Remove side fabric panels. Remove the connection (e.g. securing splint and pin) (Fig. 90,2) between the push rod (Fig. 90,3) and lever (Fig. 90,1). Remove the push rod. Open or close the pull-down bed manually. Contact customer service. 6.10.
6 Living Z Do not use the bed in the elevating roof for luggage storage. When the bed is not being used, only keep the bed linen required for 2 people and the access ladder in it. Z Never pull down the bed in the elevating roof together with the elevating roof. Depending on the model, the vehicle is fitted with a elevating roof. The bed in the elevating roof can be used immediately without additional conversions after the elevating roof has been opened (see section 6.6).
Living 6 6.12 Sleeping conversion Z Depending on the model, the seating group can be different in shape and position to the one shown here. Z Depending on the model, an enclosed additional cushion must be inserted between the seat cushions. 6.12.1 Central seating group 1 2 3 4 Fig. 92 Prior to conversion Fig. 93 After conversion Back cushion Seat cushion Table-top Bedding box Slightly raise the front of the table-top (Fig. 92,3).
6 Living 6.12.2 Central seating group with lengthwise individual seat 1 2 3 4 5 6 Fig. 94 Prior to conversion Fig. 95 During conversion Fig. 96 After conversion Back cushion Seat cushion Lift-off table Seat cushion Back cushion Additional cushion Align the lift-off table (Fig. 94,3) centrally between the seats using the lon- gitudinal/transverse adjustment (see section 6.8). Convert the lift-off table (Fig. 95,3) to a bed foundation (see section 6.8). Remove the back cushions (Fig.
Living 6 6.12.3 Central bench with lengthwise seat 1 2 3 4 5 6 7 8 9 Fig. 97 Prior to conversion Fig. 98 During conversion Fig. 99 After conversion Back cushion Seat cushion Table Back cushion Seat cushion Table extension Support plate Additional cushion Additional cushion Extend the table (Fig. 97,3) and convert the extended suspension table into a bed foundation (see section 6.8). Pull the seat cushion of the bench (Fig. 97,2) forwards. Place the seat's back cushion (Fig.
6 Living 6.12.4 Front bench seat 1 2 3 4 5 Back cushion Seat cushion Table Driver's seat Additional cushion Fig. 100 Prior to conversion Fig. 101 After conversion Turn the driver's seat (Fig. 100,4) and push it all the way forward. Convert the table (Fig. 100,3) to a bed foundation (see section 6.8). Pull the seat cushion (Fig. 101,2) forwards. Insert the back cushion (Fig. 101,1) between the seat cushion and the rear wall. Place the additional cushion (Fig. 101,5) on the driver's seat.
Gas system 7 Chapter overview 7Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: z z z z z safety changing the gas bottles gas isolator taps external gas connection automatic switching facility The operation of the gas operation appliances of the vehicle is described in chapter 9. 7.
7 Gas system X Propane gas is capable of gasification up to -42 °C, whereas butane gas gasifies at 0 °C. Below these temperatures no gas pressure is available. Butane gas is unsuitable for use in winter. X Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than ten years after the manufacturing date.
Gas system 7 X Use the shortest possible tube lengths (150 cm max.) for external gas bottles. X Never block the floor ventilation openings below the gas bottles. Z With some models, the gas bottle compartment is located right next to the conversion door. With these models, only open the gas bottle compartment when the conversion door is closed. Danger from damages. Z For gas-operated units the gas pressure must be reduced to 30 mbar.
7 Gas system 7.4 Gas isolator taps 1 2 3 4 5 Heater/boiler Refrigerator Cooker Gas pipe Pipe to the gas appliance Fig. 103 Symbols for the gas isolator taps A gas isolator tap (Fig. 103) for every gas device is built into the vehicle. The gas isolator taps can be found under the cooker. Opening: Position the gas isolator tap of the corresponding appliance parallel (Fig. 103,1) to the pipe (Fig. 103,5) leading to the gas appliance.
Gas system 7 Fig. 104 External gas connection, gas isolator tap closed The external gas connection (Fig. 104) is located at the rear or to the left or right of the vehicle depending on the model. Connect the external gas device to the connection point (Fig. 104,1). Open the gas isolator tap (Fig. 104,2). 7.6 7.6.1 Automatic switching facility DuoControl switching facility X Do not use the switching facility in closed spaces.
7 Gas system The reversing valve is equipped with the regulator defroster Eis-Ex. This prevents damage to the gas system during the winter months. Only the electrical functions can be switched at the operating unit (Fig. 106). The regulator taps on the gas bottles (Fig. 105,1 and 6) must be opened manually. The reversing valve provides a constant gas pressure, regardless of which gas bottle is being drawn upon. The two indicator lamps on the operating unit indicate the level of the primary bottle.
Gas system 7 7.6.2 DuoComfort switching facility X Do not use the switching facility in closed spaces. Z If the vehicle is equipped with a panel from the DT line, the switching facility is operated via the panel. The operating unit is not provided in these models. Z Also read the manufacturer's instruction manual. The DuoComfort is an automatic switching facility with a remote display for a two-bottle gas system.
7 Gas system Putting into operation: Open the regulator taps on the gas bottles (Fig. 107,1 and 5). Use the knob (Fig. 107,7) on the regulator (Fig. 107,3) to select the gas bottle which is to be the primary source of gas (primary bottle). Always turn the knob as far as it will go. Switch on the DuoComfort switching facility at the operating unit (Fig. 108). To do so, set the rocker switch (Fig. 108,2) to winter operation "On and heating" (Fig. 108,4) or to summer operation "On" (Fig. 108,6).
Electrical system 8 Chapter overview 8Electrical system This chapter contains instructions regarding the electrical system of the vehicle.
8 Electrical system Total discharge Total discharge of the battery is imminent, if a battery is completely discharged by an active appliance and by closed circuit current and the off-load voltage falls below 12 V. Z Total discharge damages the battery. Capacity Capacity refers to the amount of electricity which can be stored in a battery. The capacity of a battery is given in ampere hours (Ah). The so-called K20 value is normally used.
Electrical system 8 8.3.2 Starter battery The starter battery serves for starting the engine and supplies the electrical appliances of the base vehicle as well as optional devices such as the radio, navigation system or central locking system with voltage. Position Discharging Look up the following table for the position.
8 Electrical system Switch off all gas appliances, all gas isolator taps and close the regulator tap on the gas bottle. Disconnect the starter battery from the vehicle (e.g. remove the battery ter- minals). There is a danger of short circuit when disconnecting the battery poles. For this reason, first disconnect the negative terminal on the starter battery and then the positive. Check that the external charger is turned off. Connect the external charger to the starter battery.
Electrical system 8 Z The battery is maintenance-free. Maintenance-free means: It is not necessary to check the acid level. It is not necessary to lubricate the battery poles. It is not necessary to refill the distilled water. Even a maintenance-free battery must be charged regularly. When the vehicle is not connected to the 240 V power supply or the 240 V power supply is switched off, the living area battery supplies the living area with 12 V DC. The living area battery has a limited power supply only.
8 Electrical system Fig. 109 Connection auxiliary batteries 1 2 3 Connection auxiliary batteries Seat console in the driver's cabin on the left hand side Seat console in the driver's cabin on the right hand side Living area seat console To allow all the batteries to be charged or discharged evenly, the batteries must be connected according to Fig. 109. X Always connect the load and charging lines cross-wise.
Electrical system 8 Z The example calculation refers to a new, optimally charged battery. The actual effective battery capacity depends on the current charging condition and the age of the battery. The current battery capacity can be determined by means of special indicator units. Record the daily requirement. Note the switching on times and the power output of the devices used (see table below). Example: In the morning, three spotlights with 10 watts [W] each are lit in the bathroom for 30 minutes.
8 Electrical system Two solar cells of 50 W produce the following gain: z Summer: Approx. 34 Ah/day (independent operation reached) z Winter: Approx. 8-9 Ah/day (in order to prolong independent operation, another living area battery must be installed) 8.4 Transformer/rectifier (EBL 99) Z Do not cover the ventilation slots. Danger of overheating! Z Depending on the model, not all slots for the fuses are occupied. Z If there are several living area batteries, use an auxiliary charging unit.
Electrical system 8 z The transformer/rectifier provides connections for a solar charge regulator and an auxiliary charging unit as well as other control and monitoring functions. z When the engine is turned off, the transformer/rectifier separates the starter battery electrically from the living area battery. This prevents the 12 V living area appliances from discharging the starter battery.
8 Electrical system Measures: Switch off all electrical appliances that are not absolutely essential at the corresponding switch. If necessary, use the 12 V main switch to switch the 12 V power supply back on for a short while. This is only possible, however, when the battery voltage is above 11 V. If the voltage is below this level, the 12 V power supply cannot be switched on again until the living area battery has been recharged. 8.4.
Electrical system 8 8.5 Panel (LT 95) Fig. 111 Panel (LT 95) 1 2 3 4 5 6 7 8 9 10 Indicator scale for battery voltage Indicator scale for tank fill level Alarm warning light 12 V indicator lamp Rotary knob Starter battery symbol Waste water tank symbol Water tank symbol Living area battery symbol 240 V indicator lamp Z Further information can be obtained in the manufacturer's instruction manual. 8.5.1 Switching the 12 V power supply On/Off The rotary knob (Fig.
8 Electrical system 8.5.2 Battery voltage display Z The battery voltage will be displayed for approx. 20 seconds after it has been called up. Use the rotary knob (Fig. 111,5) for reading the voltage of the living area battery as well as that of the starter battery. The voltage is displayed on the indicator scale for battery voltage (Fig. 111,1). Displays: Turn the rotary knob (Fig. 111,5) until the symbol for the desired battery lights up.
Electrical system 8 Z Measure the off-load voltage preferably several hours after the previous charging (e.g. in the morning) and not directly after a current drain. 8.5.3 Displaying the tank water level Z The tank fill level will be displayed for approx. 20 seconds after it has been called up. Use the rotary knob (Fig. 111,5) for checking the fill level of the water tank or the waste water tank. The fill level is displayed on the indicator scale for the tank fill level (Fig. 111,2).
8 Electrical system Measures: Fill water tank or empty waste water tank. 240 V indicator lamp Z If the vehicle is connected to the 240 V power supply, the 240 V indicator lamp is lit even if the 12 V power supply is switched off via the rotary knob. The 240 V indicator lamp (Fig. 111,10) illuminates whenever line voltage is available at the transformer/rectifier input. 8.6 240 V power supply X Only allow qualified personnel to work on the electrical system.
Electrical system 8 Z The 240 V connection in the vehicle is equipped with a fault current protec- tion switch (FI-switch). Z For the connection points on camp sites (camping distributors) fault current protection switches (FI-switches, 30 mA) are obligatory. The vehicle can be connected to an external 240 V power supply. Fig. 112 240 V fuse box with safety cutout and FI-switch Connecting the vehicle: Fig.
8 Electrical system 8.7.1 12 V fuses The appliances connected to the 12 V power supply in the living area are fused individually. The fuses are accessible at different positions in the vehicle: z z z z z On the transformer/rectifier On the fuse holder on the transformer/rectifier Under the seat consoles On the starter battery In the housing frame of the sewage tank 1 2 Unbroken fuse element Broken fuse element Fig. 114 12 V fuse An intact 12 V fuse can be detected by the unbroken fuse element (Fig.
Electrical system 8 Fuses on the living area battery The fuses are fitted next to the living area battery. 1 2 Jumbo flat fuse 50 A/red (for the transformer/rectifier) Flat fuse 2 A/grey (for battery sensor, living area battery) Fig.
8 Electrical system Fuses on the fuse holder The fuses are fitted next to the transformer/rectifier. The fuses are secondary fuses for reserve 4 (25 A) on the transformer/rectifier. 1 2 3 Flat fuse 2 A/grey (F1) (refrigerator control) Flat fuse 10 A/red (F2) (satellite system) Flat fuse (spare) Fig. 118 Fuses on the fuse holder Fuses on the relay box AD01 Fiat base vehicle A relay box (AD01) is installed in the seat console in the driver's cabin on the right hand side.
Electrical system 8 Function Value/colour Spare 1 (optional devices gas system) 2 A grey Solar 15 A blue Reserve 5 (TV connection in rear) 10 A red Reserve 6 (12 V additional plug socket) 10 A red Auxiliary charging unit 1) Fuse for the Thetford toilet (swivel toilet) 20 A yellow Circuit 1 15 A blue Circuit 2 15 A blue TV 10 A red Water pump 5 A beige with secondary fuses on the fuse holder The fuse is located in the locker wall of the sewage tank. 1 Flat fuse 3 A/purple Fig.
8 Electrical system Fuse for electrically operated skylight (Ford base vehicle) 8.7.2 The fuse is installed next to the fuse box on the front passenger side. Flat fuse 10 A red. 240 V fuse Z Check the fault current protection switch for each connection to the 240 V power supply, at least once every 6 months. Fig. 121 240 V fuse box with safety cutout and RCD A fault current protection switch (RCD) (Fig. 121,5) in the fuse box (Fig. 121,3) protects the complete vehicle from fault current (0.03 A).
Electrical system 8 8.8 8.8.1 Circuit diagrams Block diagram 240 V Fig. 122 240 V circuit diagram 1 2 3 4 5 6 7 Transformer/rectifier Auxiliary charging unit Refrigerator Sockets Automatic circuit breaker Optional device (e.g. air conditioning unit) 240 V connection Fig. 122 shows a schematic diagram of the 240 V network.
8 Electrical system 8.8.2 Block diagram 12 V Fig. 123 12 V circuit diagram 1 240 V automatic circuit breaker 2 Panel with 12 V main switch 3 Solar 4 Solar regulator 5 Transformer/rectifier with battery cut off switch A Light, consumer circuits can be switched on/off via 12 V main switch 6 Spare 1, 2, 3, 5 and 6 7 Circuit 1, circuit 2 8 Water pump 9 TV set B Basic supply can be switched on/off via battery cut-off switch 10 Refrigerator 11 Spare 4 (special equipment, e.g.
Electrical system 8 8.
8 Electrical system 128 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Appliances 9 Chapter overview 9Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: z z z z z z 9.
9 Appliances X Never operate the heater in gas operation in closed spaces (e.g. garages). Danger of poisoning and suffocation! X Do not use the space behind the heater as a storage compartment. When lighting the heater for the first time a small amount of smoke and odour will occur. Immediately set the operating switch of the heater to its highest position. Open doors and windows and ventilate well. Smoke and odour will disappear by themselves after a while. 9.2.
Appliances 9 1 2 3 4 5 6 7 8 9 Fig.
9 Appliances 9.2.4 Independent vehicle heater X Do not operate the heater in closed spaces. Danger of suffocation! X Do not operate the heater at petrol stations. Danger of explosion! The inside and the engine can be heated with the independent vehicle heater. The heating of the engine can be switched off. The independent vehicle heater can be turned on and off manually or with a timer. The time for the heating to start can be exactly preselected from 1 minute to 24 hours.
Appliances 9 9.2.5 Floor warming unit, warm air X On models with a warm air floor warming unit, never drill holes in the floor or screw in any screws. The warm air ducts might be damaged. X The air outlet nozzles in the driver's cab must remain open. Otherwise, the air cannot circulate and a build-up of trapped air occurs. X Do not close or cover up the slatted grille of the air intake opening. Z The floor warming unit only works if the hot-air heater is in operation.
9 Appliances Z The electrical floor warming unit only operates if the vehicle is connected to the 240 V power supply. Z The output of the electrical floor warming unit alone is not sufficient to heat the living area. Fig. 130 Switch for electrical floor warming unit Switching on: Connect the vehicle to the 240 V power supply (see chapter 8). Press the rocker switch (Fig. 130,1). The indicator lamp (Fig. 130,2) on the switch is illuminated. Switching off: Press the rocker switch (Fig. 130,1).
Appliances 9 Set the desired operating mode with the key (Fig. 132,8). z "FAN": Only ventilation without cooling. z "COMFORT": Cooling. The fan output and the room temperature can be set separately. The green indicator lamp in the receiver indicates the compressor is in operation and therefore cooling mode. Set the desired fan output and room temperature with the keys (Fig. 132,3 and 4) if necessary. The arrow (Fig. 132,9) indicates the selected setting mode.
9 Appliances 9.4 Boiler X Never let gas escape unburned due to danger of explosion. X Never run the boiler in gas operation when refuelling, on ferries or in the garage. Danger of explosion! X Never operate the boiler in gas operation in closed spaces (e.g. garages). Danger of poisoning and suffocation! X The water in the boiler can be heated up to 65 °C. Risk of scalding! Z Never use boiler when empty. Z If the boiler is not being used, empty it if there is any risk of frost.
Appliances 9 The voltage supply for the appliance cannot be interrupted by an interruption to the 12 V supply on the panel. Depending on the model, the red indicator lamp (Fig. 133,4) on the operating unit lights up when there is a fault (see chapter 14). Safety/drainage valve The boiler is equipped with a safety/drainage valve (Fig. 134). The safety/ drainage valve prevents water in the boiler from freezing, when there is frost and the heater is not switched on.
9 Appliances Filling/emptying the boiler Filling the boiler with water: The boiler can be supplied with water from the water tank. Switch on 12 V power supply on the panel. Close the safety/drainage valve. Turn the knob (Fig. 134,1) perpendicular to the safety/drainage valve and push the push button (Fig. 134,2) in. Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water.
Appliances 9 Z Only use pots and pans whose diameter is appropriate for the gas cooker burners. Z When the flame goes out, the thermocouple automatically cuts the gas supply. Z Further information can be obtained in the manufacturer's instruction manual. The vehicle kitchen unit is fitted with a three-burner gas cooker. Gas cooker lid Depending on the model, a two-part gas cooker lid is built in. Fig. 135 Gas cooker lid When using the burner on the right (Fig.
9 Appliances Switching off: Turn the control knob to the 0-position. The flame fades. Close the gas isolator tap "Cooker" and the regulator tap on the gas bottle. 9.5.2 Gas oven X Remove cap from waste gas vent before using the gas oven. X Keep the ventilation openings on the gas oven open at all times. X There must be no flammable objects near the gas oven when it is being lit. X The oven flap must remain open when it is being lit. X If ignition has not taken place, repeat the entire procedure.
Appliances 9 Press the control knob (Fig. 138,5) and hold it down for 5 to 10 seconds. Ignition will take place automatically. Release the control knob and turn to the desired setting. Switching the grill on: Pull out the heat protection plate (Fig. 138,1). Light the grill burner (upper burner). Leave the oven flap open. Switching off: Turn the control knob (Fig. 138,4) to "OFF". The flame fades. Close the gas isolator tap "Oven" and the regulator tap on the gas bottle.
9 Appliances The gas oven is equipped with electronic ignition. Fig. 139 Gas oven (Dometic) Switching the oven on: Open the regulator tap on the gas bottle and the gas isolator tap "Oven". Open oven door completely. The safety switch then releases the ignition. Press and hold control knob (Fig. 139,1) and turn it anti-clockwise (" ") to the required setting. Keep control knob (Fig. 139,1) pressed for a further 5-10 seconds. Ignition will take place automatically. Release control knob (Fig.
Appliances 9 9.6.1 Refrigerator ventilation grill Dometic Fig. 140 Refrigerator ventilation grill (with sliding trap) Removal: Push sliding trap (Fig. 140,1) upward. Remove refrigerator ventilation grill. Thetford Fig. 141 Refrigerator ventilation grill (Thetford) Removal: Move the locking device (Fig. 141,1) to the middle. Remove refrigerator ventilation grill. 9.6.
9 Appliances Z The refrigerator always requires a 12 V control voltage, regardless of which type of energy it is using. The control voltage is drawn from the living room area battery. Therefore the closed circuit current always flows even if the refrigerator is switched off. Always disconnect the refrigerator from the battery for a temporary lay-up. Fig.
Appliances 9 When changing over from 240 V or 12 V to gas, delay times are built into the AES. For example, when changing over from 12 V operation to gas operation, a 15 minute delay is built in the AES. This prevents a change-over to gas operation when the vehicle is stopped briefly and the engine is switched off (e.g. stop to fill tank). Refrigerating temperature control When turned on the first time the refrigerator automatically selects the middle thermostat position.
9 Appliances Switching off: Press and hold the On/Off/Power-Selection button (Fig. 142,1) for about 3 seconds. The refrigerator switches off and no displays are lit. Close the gas isolator tap "Refrigerator" and the regulator tap on the gas bottle. Additional functions In automatic mode, "AES" and the type of power currently in use are displayed alternately. The brightness of the display is reduced after a few seconds if no other buttons are pressed.
Appliances 9 1 2 3 4 Button for thermostat On/Off button Display Button for operating mode Fig. 143 Operating controls for the refrigerator (Thetford without SES) Switching on: Open the regulator tap on the gas bottle and the gas isolator tap "Refriger- ator". Press the button (Fig. 143,2). The display (Fig. 143,3) lights up in blue and the current settings are displayed. Press the button (Fig. 143,4). The current setting of the operating mode appears on the display.
9 Appliances Switching the 12 V operation on: Press the button (Fig. 143,2). Press the button (Fig. 143,4) repeatedly until the 12 V operating mode " " appears on the display. Press the button (Fig. 143,1) repeatedly until the desired thermostat setting appears on the display. Switching the 12 V operation off: Press the button (Fig. 143,2). The display is no longer lit up. Refrigerator is switched off.
Appliances 9 Dometic 8 series Fig. 144 Release button of the refrigerator door (Dometic 8 series) Opening: Closing: Fig. 145 Lock hook fixture Press the release button (Fig. 144,1) and open the refrigerator door. Close the refrigerator door. The lock hook engages audibly. When the vehicle has been positioned, the lock hook can be fixed. The refrigerator door can now be opened without having to press the release button. Fixing the lock hook: Press the fixture (Fig. 145,1) upwards.
9 Appliances Thetford Fig. 148 Lock of refrigerator door, closed (Thetford) Opening: Fig. 149 Refrigerator door in ventilation position (Thetford) Open the refrigerator door at the handle (Fig. 148,2). The lock (Fig. 148,1) is released automatically. Closing: Locking in the ventilation position: Fully close the refrigerator door. Ensure that the lock is engaged. Slightly open refrigerator door. Open the lock (Fig. 149,2) and snap it into the locking catch (Fig. 149,1).
Sanitary fittings 10 Chapter overview 10Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. The instructions address the following topics: z z z z z 10.1 water tank waste water tank complete water system toilet compartment toilet Water supply, general X Fill water tank from supply systems that have been verified to provide drinking water quality. X Only use such hoses or containers when filling that have been approved for use with drinking water.
10 Sanitary fittings 10.2 Water tank The water tank can contain 20 l to 150 l depending on the model. Z For driving safety and for regulatory reasons, when the vehicle is motion the fill quantity must be reduced to approximately 20 litres. If the water is drained using the safety drainage handle (see section 10.2.3), a residual quantity of approximately 20 litres will remain in the water tank. 10.2.
Sanitary fittings 10 Open drinking water filler neck. Fill the water tank with drinking water. Use a water hose, a water canister with a funnel or similar for filling. Close drinking water filler neck. 10.2.3 Reducing the water quantity for mobile operation X When filling the water tank, observe the maximum permissible gross weight of the vehicle. Luggage must be reduced accordingly when the water tank is full. Handle The handle is installed on the water tank. Fig.
10 Sanitary fittings 10.2.5 Draining water (stopper) Fig. 153 Water tank Unscrew the cap (Fig. 153,1) on the water tank. Remove the stopper (Fig. 153,3) from the drainage opening (Fig. 153,2). The water will drain. Screw the cap back on the water tank. 10.3 Waste water tank Hot air from the living area heater heats the waste water tank. This protects the waste water tank from frost.
Sanitary fittings 10 Emptying: Attach the waste water hose to the drain pipe (Fig. 154,2). Open drain cock. To do this, turn the operating lever (Fig. 154,1) of the drain cock one quarter turn. The operating lever is in a horizontal position or parallel to the drain pipe. The waste water will run out. Completely empty waste water tank. Close the drain cock again once all of the waste water has run out. To do this, turn the operating lever (Fig. 154,1) of the drain cock one quarter turn.
10 Sanitary fittings Close drinking water filler neck. Check that the cap on the water tank is not leaking. 10.5 Emptying the water system Z If the vehicle is not used for several days or if it is not heated when there is a risk of frost, empty the entire water system. Make sure that the 12 V power supply on the panel is switched off. Otherwise, the water pump will overheat and may get damaged. Leave the water taps on in central position.
Sanitary fittings 10 10.6 Toilet compartment Z Do not transport any loads in the shower tray. The shower tray or other items of equipment in the toilet compartment can be damaged. Z For ventilation purposes during or after a shower, and for drying wet clothing, close the toilet compartment door and open the window or the toilet compartment skylight. This improves the air circulation. Z Use the shower handset for showers. To do so, pull out the shower handset.
10 Sanitary fittings 10.7.1 Swivel toilet The flushing of the Thetford toilet is fed directly from the water system of the vehicle. The toilet bowl can be moved into the optimal position. Fig. 156 Thetford toilet bowl, swivelling Fig. 157 Flush button/indicator lamp Thetford toilet The operating unit is located close to the toilet bowl. Flushing: Before flushing open the sliding trap of the Thetford toilet. To do this, push the slide lever (Fig. 156,1) in an anticlockwise direction.
Sanitary fittings 10 10.7.3 Emptying the sewage tank Z The sewage tank can only be taken out if the sliding trap is closed. Fig. 160 Flap for the sewage tank Fig. 161 Sewage tank Slide the slide lever on the toilet bowl in a clockwise direction. The sliding trap is closed. Open the flap for the sewage tank on the outside of the vehicle. Insert the key into the locking cylinder of the push-button lock (Fig. 160,1) and turn a quarter turn in a clockwise direction. Remove the key.
10 Sanitary fittings 10.7.5 Temporary lay-up Z If the toilet is not to be used for an extended period, empty the water tank, the sewage tank and the water pipes. Laying up the toilet: Empty the water tank. Flush the toilet until no more water runs into the toilet. Empty the sewage tank. Rinse the sewage tank thoroughly. Leave the drainage neck on the sewage tank open. Let the sewage tank dry for as long as possible.
Care 11 Chapter overview 11Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: z z z z z exterior of the vehicle interior cushions water system winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time. The checklist address the following topics: z temporary lay-up z winter lay-up z start-up after a lay-up 11.1 11.1.
11 Care 11.1.3 Washing the vehicle Z Never clean the vehicle in the car wash. Water can enter the refrigerator grills, the waste gas vents, the ventilation of the extractor hoods or the forced ventilations. The vehicle could be damaged. Wash the vehicle only on a washing site intended for this purpose. Avoid full sunshine. Observe environmental measures. Only clean external applications and synthetic parts with plenty of warm water, dish washing liquid and soft cloth.
Care 11 Follow-up treatment of GRP add-on parts: Wash the vehicle and allow to dry as described above. Check if the GRP add-on parts are clean and dry. Apply the polisher with a soft cloth evenly on the surface of the GRP add- on part. Wait until a light grey film forms. Wipe the GRP add-on part with a dry, soft cloth. Move the cloth in circles over the surface of the GRP add-on part. We recommend using a polishing machine for this work. Z Paint protection has to be used to preserve the polish.
11 Care Z Do not pour any corrosive agents into the drain holes. Never pour boiling water directly into the drain holes. Corrosive agents and boiling water cause damage to drainage pipes and siphon traps. Z Do not use vinegar based products to clean the toilet and water system, or for decalcification of the water system. Vinegar-based products may cause damage to seals or parts of the installation. Use standard decalcifying products for decalcification. Z Save water. Mop up all remaining water.
Care 11 Z Always only dab moist or greasy marks, never rub them. It is most effective to gently press an absorbent cloth or a sponge onto the mark. Z Do not wash upholstery. Z When cleaning leather covers, make sure that the leather is not soaked through and that no water seeps through the seams of the leather covers. Z Treat the mark from the outside working inwards. This prevents the mark from spreading. Z In the case of both solid or softer contamination, first remove the coarse parts.
11 Care Vomit Carefully clean up the vomit and wash it out with cold water. Use only ordinary water-based cleaning agents. Alternatively, mix 2 tablespoons of ammoniac with 1 litre of water. Gently dab the mark with a cloth moistened with this solution. Turn the cloth frequently so that the mark only comes into contact with a clean part of the cloth. 11.4 Water system 11.4.1 Cleaning the water tank Empty the water tank and close the drainage opening. Remove the cap of the water tank.
Care 11 Empty the water system. Collect the mixture of water and cleaning agent for correct disposal. For rinsing fill the entire water system with drinking water and empty again several times over. 11.4.3 Disinfecting the water system Z Only use suitable disinfectants as sold by the specialist trade. Z Collect any emerging mixture of water and disinfectant for correct disposal. Empty the water system. Close all drain holes and drain cocks.
11 Care Z If there is any risk of frost, always run heater at a minimum of 15 °C. Switch the circulation fan (if there is one) to automatic. In the case of extreme external temperatures, the furniture flaps and doors should be left slightly open. The inflowing warm air can help prevent the freezing of water pipes, for example, and counteract the formation of condensation in the storage spaces. Z If there is any risk of frost, cover the outside surface of the windows with winter insulation mats. 11.6 11.
Care 11 Activities Body Done All vents should be sealed with the appropriate caps and all other openings (apart from forced ventilations) should also be sealed. This prevents animals (e.g. mice) from gaining entry Air the interior, all storage compartments accessible from the outside, and the parking space (e.g.
11 Care Activities Done Brush oil or glycerine on all locking mechanisms Rub all rubber seals with talc Use graphite dust to treat locking cylinders Interior Position de-humidifiers Remove upholstery from the vehicle and store in a dry place Air the interior every 3 weeks Empty all cabinets and storage compartments, open flaps, doors and drawers Thoroughly clean the interior If there is a risk of frost, do not leave the flat screen in the vehicle Electrical system Remove the starter battery and the li
Care 11 Activities Electrical system Done Connect to 240 V power supply using the external socket Fully charge living area and starter battery Z Charge the battery for at least 20 hours after lay-up. Connect the living area battery with the 12 V power supply. To do this, switch on the battery cut-off switch on the transformer/rectifier (see chapter 8) Check that the electrical system are working, e.g.
11 Care 172 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Customer service and maintenance 12 Chapter overview 12Customer service and maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle.
12 Customer service and maintenance 12.4 Air conditioning unit Z Never operate the air conditioning unit without a lint filter. Without a lint filter, the vaporiser becomes dirty and the capacity of the air conditioning unit is consequently impaired. Z Condensation can enter the vehicle if the condensation drain is clogged up. Keep the condensation drain free from dirt, leaves and similar. Fig. 162 Air conditioning unit (Truma) A lint filter (Fig.
Customer service and maintenance 12 Pos. in Fig.
12 Customer service and maintenance Daytime running light (Fig. 165,1) Low beam/main beam (Fig. 165,2 and Fig. 166,1) The daytime running light can only be replaced as a whole unit. Contact an authorised dealer or a service centre to replace it. Open the bonnet (see chapter 4). Put your hand behind the lamp holder. Turn the lamp holder with the lamp in an anticlockwise direction and remove. Turn the bulb in an anticlockwise direction and remove from the holder. Put in a new bulb.
Customer service and maintenance 12 Front headlight with direction indicator The direction indicator is integrated into the front headlight. The front headlight bulbs are changed from the engine compartment. Fig. 168 Front headlight (front side) Direction indicator (Fig. 168,1 and Fig. 169,1) Fig. 169 Front headlight (rear side) Open the bonnet (see chapter 4). Turn the lamp holder with the lamp in an anticlockwise direction and remove.
12 Customer service and maintenance Fig. 170 Adjusting front headlight Open the bonnet (see chapter 4). Remove the rubber cap from lamp housing. Swivel the two adjusting levers (Fig. 170,1) to the other side. Z For resetting, swivel the adjusting levers back to their original position. 12.5.3 Front lights (Fiat) 1 2 3 4 Low beam/main beam/parking light Fog light (dependent on model) Direction indicator Clearance light (dependent on model) Fig.
Customer service and maintenance 12 12.5.4 Rear lights HYMER Only a service centre may replace the third brake light. Fig. 172 Rear lights (front side) Fig. 173 Rear lights (rear side) Loosen three hexagon socket screws (Fig. 172,6) Remove housing. On the housing rear, remove the two Torx screws (Fig. 173,6) of the retainer. Change bulb. ERIBA Replace third brake light only as a complete unit. Fig. 174 Rear lights (tail lights) Unscrew the housing screws (Fig.
12 Customer service and maintenance Van Replace third brake light only as a complete unit. 1 2 3 Brake light/rear light Direction indicator Reverse light (right)/fog tail light (left) Fig. 175 Rear lights (tail lights) Undo housing screws of the lamps (Fig. 175,1 to 3). Remove housing. Change bulb. Licence plate light The licence plate light is the same for all models. Fig. 176 Rear lights (licence plate light) Undo the two housing screws (Fig. 176,1). Remove housing. Change bulb. 12.5.
Customer service and maintenance 12 Side marker light Use a suitable tool (e.g. a screwdriver) to lever out the cover. Apply the tool to the notch in the housing. Remove housing. Change bulb. Direction indicator The lamp is glued in. If the bulb is faulty, contact an authorised dealer or service centre. Marker light The lamp is glued in. If the bulb is faulty, contact an authorised dealer or service centre. 12.5.
12 Customer service and maintenance Hook at the upper edge of the housing must engage with the recess of the holder. Press down housing. 12.5.7 Types of bulbs for exterior lighting Integrated Item no.
Customer service and maintenance 12 Partially integrated Front The bulb types are described in the instruction manual of the base vehicle. Item no. Rear (HYMER) Rear (ERIBA) Rear (Van) Side 12.
12 Customer service and maintenance X Lights can get very hot. When the light is switched on, there must always be a safety distance of 30 cm between light and flammable objects. Fire hazard! X Do not replace the LEDs in lamps with standard light bulbs. Risk of fire due to intense heat build up. Z A new bulb should not be touched with the fingers. Use a cloth when installing the new bulb. Z Only use bulbs of the same type and with the correct wattage.
Customer service and maintenance 12 12.6.3 Recessed halogen light (flat) Fig. 182 Recessed halogen light (flat) The recessed halogen light (Fig. 182,2) is installed flush with the panel. Changing bulbs: Use a suitable tool (e.g. a blunt knife) to lever out the internal cover ring with glass disk (Fig. 182,1) from the housing. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. 12.6.4 Skylight spotlight Fig.
12 Customer service and maintenance 12.6.5 Wardrobe light Fig. 184 Wardrobe light Changing bulbs: Press the light covering (Fig. 184,1) lightly together and remove it. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. 12.6.6 Garage light Fig. 185 Garage light Changing bulbs: Undo the fastening screw (Fig. 185,2). Remove the cover (Fig. 185,1). Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. 12.6.
Customer service and maintenance 12 12.7 Adjusting the springs of the blind and the insect screen Z The spring adjustment screw cannot be turned back. Fig. 186 Re-tensioning the spring tension Depending on the model, the tensile force of the spring for the blind or the insect screen can be adjusted if necessary. Two adjustment screws for the blind (Fig. 186,1) and the insect screen (Fig. 186,2) are at the left side of the window frame.
12 Customer service and maintenance Here are some suggestions of important spare parts: z z z z z Fuses V-belt Windscreen blades Bulbs Water pump (submerged pump) When ordering spare parts, please indicate the serial number and the vehicle type to the authorised dealer or service centre. The vehicle described in this instruction manual is built and equipped to factory standards. Special equipment is offered depending on its purpose or use.
Customer service and maintenance 12 12.11 Dealers Contact your authorised dealer or service centre whenever spare parts are needed for the vehicle. You can find the addresses and telephone numbers of the authorised dealers and service centres: z In the brochure "HYMER dealers", which is included separately with the vehicle z In the Internet at http://www.hymer.com 12.
12 Customer service and maintenance 190 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Wheels and tyres 13 Chapter overview 13Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: z z z z tyre selection handling of tyres changing wheels spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 13.1 General X Check tyre pressure before a journey or every 2 weeks.
13 Wheels and tyres Fig. 188 Tighten the wheel nuts or wheel bolts cross-wise Check regularly that the wheel nuts or wheel bolts are firmly seated. Re- tighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 188) after 50 km (30 miles). See section 13.5.2 for tightening torque. When using new or newly painted rims, re-tighten the wheel nuts or wheel bolts once again after approx. 1,000 to 5,000 km (600 miles to 3,000 miles).
Wheels and tyres 13 13.3 215/70 R 15C 109/107 Q (example) 13.4 Tyre specifications Description Explanation 215 Tyre width in mm 70 Height-to-width proportion in percent R Tyre design (R = radial) 15 Rim diameter in inches C Commercial (transporter) 109 Load index code for single tyres 107 Load index code for twin tyres Q Speed index (Q = 160 km/h) Handling of tyres Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched.
13 Wheels and tyres X Never overload the vehicle jack. The maximum permissible load is spec- ified on the vehicle jack's identification plate. X Use the vehicle jack only for lifting the vehicle briefly while changing the tyre. X Do not start the motor while the vehicle is jacked up. X Whilst the vehicle is in a jacked up position, persons must not lie down under it. Z Do not damage the thread of the thread bolt or wheel nut when changing the wheel.
Wheels and tyres 13 13.5.3 Changing a wheel X The footplate of the vehicle jack must be levelly positioned on the ground. Z The wheel you have replaced should be repaired immediately. Z Take note of the general instructions in this chapter. Park the vehicle on as even and stable a surface as possible. Go into first gear. In the case of automatic transmission, change gear to "P" position. Apply the handbrake. Place chocks or other appropriate objects beneath the vehicle to secure it.
13 Wheels and tyres 13.6.1 Spare wheel in rear storage space or rear garage Fig. 189 Spare wheel in the rear storage space Removing the spare wheel: Loosen the wing nut (Fig. 189,1) and unscrew it. Remove the pad (Fig. 189,2). Remove the spare wheel. 13.7 Tyre pressure X Tyres overheat if the tyre pressure is too low. This can cause serious tyre damage. X Check tyre pressure before a journey or every 2 weeks.
Wheels and tyres 13 The vehicles are constantly brought up to the newest technical standards. It is possible that new tyre sizes are not yet included in this table. If this is the case, any authorised dealer or service centre will be happy to provide the newest values. 13.7.1 Fiat base vehicle 2-axle vehicle Tyres 13.7.
13 Wheels and tyres 198 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Troubleshooting 14 Chapter overview 14Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies.
14 Troubleshooting Fault Cause Remedy Starter or living area battery is not charged when operated in 240 V mode Fuse on the transformer/ rectifier is defective Replace fuse on the transformer/rectifier Charger module in the transformer/rectifier is defective Contact customer service Living area battery is not charged during vehicle operation Fuse on terminal D+ of the alternator is defective Replace fuse Disconnector relay in the transformer/rectifier is defective Contact customer service 12 V
Troubleshooting 14 Fault Cause Remedy Starter battery is discharged in 12 V operation Disconnector relay in the transformer/rectifier is defective Contact customer service Battery cut-off switch or main switch on the transformer/rectifier is switched off Switch battery cut-off switch or main switch on Living area battery is discharged Charge living area battery immediately No voltage is supplied by the living area battery Z Total discharge damages the battery.
14 Troubleshooting 14.4 14.5 Gas cooker/gas oven Fault Cause Remedy Ignition fuse does not operate (flame does not burn after the control knobs are released) Heat-up time is too short Keep control knob pressed for approx. 15 to 20 seconds after ignition Ignition fuse is defective Contact customer service Flame extinguishes when being reduced to its minimum setting Thermocouple sensor is incorrectly set Correctly reset thermocouple sensor (do not bend).
Troubleshooting 14 14.
14 Troubleshooting Error code 14.6.2 Cause Remedy 9 The gas supply has been cut off.
Troubleshooting 14 Fault Cause Remedy "GAS" indicator lamp flashes yellow, no gas Air in the gas pipe Switch off the refrigerator with energy selector switch Open regulator tap on the gas bottle and the gas isolator tap of the refrigerator Switch on the refrigerator with energy selector switch. After 10 seconds, the AES will attempt another ignition If the "GAS" indicator lamp flashes yellow again after approx.
14 Troubleshooting 14.
Troubleshooting 14 Fault Cause Remedy Any change in the taste or odour of the water Tank filled with dirty water Clean water system mechanically and chemically; then disinfect and rinse copiously with drinking water Fuel filled into the water tank by mistake Clean water system mechanically and chemically; then disinfect and rinse copiously with drinking water.
14 Troubleshooting Z The authorised dealers and service centres are available for any spare parts requirement.
Special equipment 15 15.1 Weight details for special equipment 15Special equipment X The use of accessories, parts and fittings not supplied by HYMER AG may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product. X Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety.
15 Special equipment 210 Item designation Surplus weight (kg) Insulation mat for driver's cabin window 3 Driver's cabin insulating glass 5 Driver's cabin air conditioning unit 30 Truma air conditioning unit 25 Steady legs, 2 pcs. 9 Curve light 2 160-litre refrigerator 11 Refrigerator with oven 19 Awning 300 cm 25 Awning 350 cm 32 Awning 400 cm 40 Awning 450 cm 45 Awning 500 cm 50 Navigation system 2.5 Fog light 1 Mains supply (garage rear wall) 2 Guest bed (approx.
Technical data 16 16.1 Technical data 16Technical data Z Only the details provided in the actual vehicle documentation shall be binding with regard to the technical data. Z The measurements as well as the net weight of the vehicle may change when mounting accessories or special equipment. Differences due to manufacturing tolerances (+/- 5 %) are possible and admissable. Further information can be found in the manual of the base vehicle. The technical data are not a component of the instruction manual.
16 Technical data 212 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
Index 12 V appliance, retrofitting . . . . . . . . . . . . . . . . 12 V fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . For Thetford toilet . . . . . . . . . . . . . . . . . . . On the living area battery . . . . . . . . . . . . . On the relay box AD01 . . . . . . . . . . . . . . . On the starter battery . . . . . . . . . . . . . . . . On the transformer/rectifier (EBL 99) . . . . 12 V indicator lamp . . . . . . . . . . . . . . . . . . . . . 12 V main switch . . . . . . . . . . . . . . . . . .
Index Types of external bulbs . . . . . . . . . . . 182, 183 Wardrobe light . . . . . . . . . . . . . . . . . . . . . . 186 Bunk bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Butane gas . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 98 C Cable reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Camping gas bottles, use . . . . . . . . . . . . . . . 26, 98 Capacity of the battery . . . . . . . . . . . . . . . . . . . 106 Caravan coupling . . . . . . . . . . . . .
Index Doors Conversion door . . . . . . . . . . . . . . . . . . . . . 59 Driver's door . . . . . . . . . . . . . . . . . . . . . . . . 59 Lock . . . . . . . . . . . . . . . . . . . . . . . . . 59, 60, 61 Troubleshooting . . . . . . . . . . . . . . . . . . . . 207 Drain cock, waste water tank . . . . . . . . . . . . . 154 Drinking water filler neck . . . . . . . . . . . . . . . . . 152 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Opening . . . . . . . . . . . . . . . . . . . . . . . . .
Index Floor warming unit, warm air Switching off . . . . . . . . . . . . . . . . . . . . . . . . 133 Switching on . . . . . . . . . . . . . . . . . . . . . . . . 133 Fluorescent tubes, changing . . . . . . . . . . . . . . 183 Fog light . . . . . . . . . . . . . . . . . . . . . . . . . . 176, 177 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . 44 Forced ventilation . . . . . . . . . . . . . . . . . . . . . 22, 65 Front bench seat, sleeping conversion . . . . . . . 96 Front passenger's seat . .
Index Insect screen . . . . . . . . . . . . . . . . . . . . . 69, 70 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Roman shade . . . . . . . . . . . . . . . . . . . . . . . 70 Hot air distribution . . . . . . . . . . . . . . . . . . . . . . 130 Hot-air heater Circulation fan . . . . . . . . . . . . . . . . . . . . . . 130 Operating modes . . . . . . . . . . . . . . . . 130, 131 Switching off . . . . . . . . . . . . . . . . . . . . . . . 131 Switching on . . . . . . . . . . . . . . . . .
Index Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Bike rack . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Rear garage . . . . . . . . . . . . . . . . . . . . . . . . . 34 Rear storage space . . . . . . . . . . . . . . . . . . . 34 Roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Underfloor sliding drawer . . . . . . . . . . . . . . . 35 Load rack for roof loads . . . . . . . . . . . . . . . . . . . 33 Load see also payload . . . . . . . . . . . .
Index Refrigerator door locking mechanism Closing . . . . . . . . . . . . . . . . . . . . . . . 149, 150 Locking in the ventilation position . . . 149, 150 Opening . . . . . . . . . . . . . . . . . . . . . . . 149, 150 Refrigerator ventilation grill, removal . . . . . . . . 143 Remote control, air conditioning unit (Truma) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Replacement key . . . . . . . . . . . . . . . . . . . . . . . 189 Risk of frost damage . . . . . . . . . . . . .
Index Safety instructions . . . . . . . . . . . . . . . . . . . . 22 Weight details . . . . . . . . . . . . . . . . . . . . . . 209 Spit motor, switching on . . . . . . . . . . . . . . . . . . 141 Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Spring on the blinds, adjustment . . . . . . . . . . . 187 Starter battery Battery alarm . . . . . . . . . . . . . . . . . . . . . . . 117 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Discharging . . . . . . . . . . . . .
Index Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Excessive wear . . . . . . . . . . . 23, 39, 191, General instructions . . . . . . . . . . . . . . . . . Handling . . . . . . . . . . . . . . . . . . . . . . . . . . Identification . . . . . . . . . . . . . . . . . . . . . . . Load-carrying capacity . . . . . . . . . . . . . . . Tyre pressure . . . . . . . . . . . . . . . . . . . . . . Tyre pressure table . . . . . . . . . . . . . . . . . . Tyre selection . . . . . . . . . . . . . .
Index 222 CL/HV/EX/EC/EJ - 04/11-1 - englisch (EN) - 2048801 - HYW-0243-02EN
