User Programming Chart User Manual

ManualsBrandsHydrotech ManualsWater purifiers5600 SXT

8/7/08

SOFTENERS AND IRON FILTERS

Model 5600 SXT-User Programming Chart

Time of Day

FROM SERVICE MODE:-

• To set Time of the Day push and hold or button for 5 seconds

(*Not both Up and Down Buttons)

Display is TD (Time of Display) →

→→

→ Press or button to adjust the

display time.

Press Extra Cycle button to resume normal operation

Model 5600 SXT -User Programming Chart

FROM SERVICE MODE:-

• To set user programming push and hold and buttons for 5

seconds, and the time of day is NOT set to 12:01 PM.

Display is DO (DAY OVERRIDE) →

→→

→ [factory default setting: OFF]. Press UP/DOWN

buttons to adjust the setting.

↓

↓↓

↓

↓↓

↓

Display is RT (REGENRATION TIME) ([default:

For Iron Filters - 11:00 P.M.

For Softeners – 2:00 A.M.]

Press UP/DOWN buttons to adjust the time.

↓

↓↓

↓

↓↓

↓

Display is H (FEED WATER HARNESS) [grains per gallons default: Softeners - 15].

Iron content ppm per gallon default: Iron Filters - 20

Press UP/DOWN buttons to adjust the value. NOT AVAILABLE IF THE VALVE TYPE

IS SET TO FILTER IN MASTER PROGRAAMING.

↓

↓↓

↓

↓↓

↓

Display is RC (FIXED RESERVE CAPACITY) [Fixed reserve capacity in gallons default:

0]. Press UP/DOWN buttons to adjust the value.

↓

↓↓

↓

DOWN

Extra Cycle

Button

Extra Cycle

Button

DOWN

Extra Cycle

Button

Extra Cycle

Button

42133

Summary of content (10 pages)

PAGE 1
8/7/08 SOFTENERS AND IRON FILTERS Model 5600 SXT-User Programming Chart Time of Day FROM SERVICE MODE:• To set Time of the Day push and hold (*Not both Up and Down Buttons) Display is TD (Time of Display) → Press display time.
PAGE 2
↓ Display is CD (CURRENT DAY OF THE WEEK). Press UP/DOWN buttons to adjust the current day of the week. ONLY AVAILABLE IF DAY OF THE WEEK CONTROL IS ON IN MASTER PROGRAAMING Model 5600 SXT- Master Programming Chart FROM SERVICE MODE:- • To enter master programming mode, set the Time of Day display to 12:01 P.M.
PAGE 3
Press UP/DOWN buttons to adjust the value. ↓ Extra Cycle Button ↓ Display is H (WATER HARDNESS) → Grains per Gallon for softener and ppm per gallon of iron for iron filters will appear [factory default setting grains per gallons for Softeners – 15gpg Iron content in ppm per gallon for Iron Filters – 20ppm]. Press UP/DOWN buttons to adjust the value. ↓ Extra Cycle Button ↓ Display is RS (RESERVE SELECTION) → Type of reserve [Factory Default Setting: RC (Fixed Reserve Capacity)].
PAGE 4
↓ Display is BR (BRINE RINSE) →[Factory Setting: For Chemical Free Iron Filters 0 (0 minutes) For Iron Filters 50 (50 minutes) For Softeners 60 (60 minutes)] Press UP/DOWN buttons to adjust the time. ↓ Extra Cycle Button ↓ Display is RR (RAPID RINSE) → [Factory Setting: For Softeners and Iron Filters - 10 (10 minutes) For Chemical Free Iron Filters – 4 (4 minutes) ]. Press UP/DOWN buttons to adjust the time.
PAGE 5
Model 5600 SXT-Diagnostics Chart To enter the diagnostic mode, push and hold UP and Extra Cycle Button button for 5 seconds. Display is FR (CURRENT FLOW RATE)→ → display current flow rate in gallons per minutes. ↓ UP ↓ Display is PF (PEAK FLOW RATE)→ → display peak flow rate in gallons per unit since the last regeneration cycle. ↓ UP ↓ Display is HR (HOURS IN SERVICE)→ → display to view the hours in service since the last regeneration cycle.
PAGE 6
8/7/08 FILTERS Model 5600 SXT-User Programming Chart Time of Day FROM SERVICE MODE:• To set Time of the Day push and hold (*Not both Up and Down Buttons) Display is TD (Time of Display) → Press display time.
PAGE 7
Model 5600 SXT- Master Programming Chart FROM SERVICE MODE:- • To enter master programming mode, set the Time of Day display to 12:01 P.M. ↓ Extra Cycle Button ↓ Press and hold UP and DOWN buttons together until the programming icon replaces the service icon Display is DF (DISPLAY FORMAT) → Unit of measure for volume and display format for time [Factory Default Setting: GAL]. Press UP/DOWN buttons to adjust the settings.
PAGE 8
Display is RS (RESERVE SELECTION) → Type of reserve [Factory Default Setting: RC (Fixed Reserve Capacity)]. Press UP/DOWN buttons to adjust the setting. ↓ Extra Cycle Button ↓ Display is RC (FIXED RESERVE CAPACITY) → Reserve capacity in gallons [Factory Default Setting: 0]. Press UP/DOWN buttons to adjust the value. ↓ Extra Cycle Button ↓ Display is DO (DAY OVERRIDE) → [factory default setting: OFF]. Press UP/DOWN buttons to adjust the setting.
PAGE 9
↓ Display is D (DAY OF WEEK) →used to set the day of week in which the regeneration should occur [Factory Setting: OFF]. Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING. ↓ Extra Cycle Button ↓ Display is CD (CURRENT DAY) → used to set the current day of week in which the regeneration should occur Press UP/DOWN buttons to adjust the setting. ONLY AVAILABLE IF CONTROL TYPE IS SET TO DAY OF WEEK SETTING.
PAGE 10
↓ Display is RC (RESERVE CAPACITY)→ →display the reserve capacity in gallons.