Installation Sheet

ManualsBrandsHydrosystems ManualsPlumbingDaniela 58" Free Standing Hydroluxe SS Soaking Tub with Center Drain, Drain Assembly, and Overflow

IMPORTANT SAFETYINSTRUCTIONS

GENERAL INSTRUCTIONS

INSTALLER -

Please pass these

IMPORTANT

instructions along to

the homeowner!

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

TABLE OF CONTENTS

Follow All Instructions, Installation Instructions, General Requirements ...............................PAGE 2

Bathtub Installation....................................... .........................................................................PAGE 3

Bathtub Installation Continued..................... ..........................................................................PAGE 4

Supplemental Install Information, Thermal Air Installation......................................................PAGE 5

Install Instructions For Tubs Without A Pedestal....................................................................PAGE 6

User Care And Maintenance, Limited Warranty .....................................................................P

AGE 7

Limited Warranty Continued....................................................................................................PAGE 8

STON COLLECTION FREESTANDING MODEL

Please refer to www.hydrosystem.com for videos on how to install your bathtub and get specific dimensions on your

model bathtub

– 1 –

Summary of content (8 pages)

PAGE 1
INSTALLER ese h t s s a p e s Plea T IMPORTAN ng to o l a s n o i t c instru ner! w o e m o h the STON COLLECTION FREESTANDING MODEL IMPORTANT SAFETYINSTRUCTIONS GENERAL INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. TABLE OF CONTENTS Follow All Instructions, Installation Instructions, General Requirements................................PAGE 2 Bathtub Installation....................................... .......................................................
PAGE 2
WARNING: When using your Hydro Systems whirlpool tub, basic precautions should be followed. READ AND FOLLOW ALL INSTRUCTIONS. 1. DANGER: To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times. 2. Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 3. Never drop or insert any object into any opening. 4. Do not operate this unit without suction cover installed. 5.
PAGE 3
Please refer to www.hydrosystem.com for videos on how to install your bathtub and get specific dimensions on your model bathtub BATHTUB INSTALLATION PREPARATION FIGURE 1 1 Clean, level, and prepare the floor for installation. 2 Place the unit in the exact installed position on the floor and trace the outline of the bath with a pencil or any erasable marking (Figure 1). Templates for Freestanding bathtubs come with the tub.
PAGE 4
FIGURE 5A INSTALL BATHTUB 10 Apply generous bead of adhesive or silicone to the bottom of the tub supports (Figure 5A). 11 Then apply a bead of tub and tile caulk or silicone around the edge of the base (Figure 5B). 12 Carefully set tub into position (Figure 6) and connect the drain hardware (previously installed). FIGURE 5B FIGURE 6 FIGURE 7 Overflow O-Ring D980-CAP 2-7/8” D980-RING 792A-BJ OVERFLOW INSTALL 13 5/16” Apply a thin bead of silicone around face of the overflow O-ring.
PAGE 5
FIGURE 8 COMPLETE BATHTUB INSTALLATION 15 Fill tub with water to the overflow and then drain the tub while inspecting the waste connections below the floor for leaks. Access from below will be necessary for this step (Figure 8). SUPPLEMENTAL INSTALLATION INFORMATION FREE STANDING TUBS GENERAL INFORMATION • Rough In Dimensions – For critical dimensions, we suggest taking the measurements of the actual tub on site. All printed specifications are +/- ½ inch and subject to change without notice.
PAGE 6
• It is not recommended that the blower be mounted over 8 feet away from the tub. The supplied wiring between the tub and the blower is approximately 10 feet long. • Remote blower locations – There are several locations where the blower can be located. There must be a GFCI electrical outlet within 2 feet of the blower. The blower is approximately 9.25 inches long and 8 inches in diameter and 5” high.
PAGE 7
12) Connect the ‘P-trap’ to the drain kit. 13) Use clear silicone to seal the gap between the overflow pipe and the floor. Lower bell flange to the floor. Attach overflow cover and thread stopper assembly into waste flange. Fill tub to overflow and allow water to stand for 30 minutes. Check carefully for any leaks. NOTE: The overflow is a plumbing device designed to prevent water from reaching a certain level in your tub. DO NOT, under any circumstances, tape off or block the overflow in any way.
PAGE 8
Accordingly, HYDRO SYSTEMS, INC. is not responsible for any such warranties or representations. THERE ARE NO WARRANTIES BEYOND THE DESCRIPTION ON THE FACE HEREOF. NO WARRANTY OF MECHANTABILITY, FITNESS, NOR OTHER WARRANTY (WHETHER EXPRESS, IMPLIED OR STATUTORY) IS MADE BY HYDRO SYSTEMS, INC., EXCEPT THAT IT WARRANTS THE GOODS TO BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP IN NORMAL USE AND SERVICE AS DESCRIBED ON THE FACE HEREOF. WARRANTY OBLIGATIONS OF HYDRO SYSTEMS, INC.