Instructions / Assembly

HF2 SERIES
Slim Flat Cap Filter Housings
Data Sheet
Tested and certi ed by NSF International to ANSI/
NSF Standard 42 for material requirements only.
Distributed by:
An American Company
JUST ADD WATER
TM
LIT-HF2-DS 08/30/18
P.O. Box 2235 Chino Hills, CA 91709 | USA
[e-mail] • www.HydronixWater.com
Materials of Construction
Opaque Housing: Polypropylene
Clear Housing: San
Cap: Polypropylene
O-Ring: Buna-N
Operating Data
Maximum Temperature: 125°F (51.7°C)
Maximum Pressure: 75 PSI (5.17 bar)
Applications
• Reverse Osmosis
• Residential Plumbing
• Photography
• Beverage
• Ice maker
• Misting Units
WARNING: READ THESE INSTRUCTIONS BEFORE CHANGING OR INSTALLING. FOLLOW
THESE INSTRUCTIONS TO REDUCE RISK OF DANGER.
Caution: filter housing must be protected against freezing and extreme temperatures.
Filter housings should not be in direct contact with sunlight for a prolonged period of
time since uv rays can make housings brittle. Pressure should always be measured before
installation and water pressure regulators should be installed in the main line or in front
of the housing if water pressure exceeds manufacturers’ maximum water pressure: 75 psi.
Installers should make sure  lters and replacement  lters are the correct length and are
not too long so as to not cause undo strain and stress on the housing. A leak detector
must be installed on all installations where high pressure, water hammer and pressure
spikes are known or suspected to be present and on all installations where pressure
is over 60 psi. Failure to the above may result in cracking of the  lter housing, water
leakage and water damage.
Caution: all filtration systems contain other parts that have a limited service life. Exhaustion
of the service life of those parts often cannot be easily detected. Commonly, it is only
after leakage has been observed or water damage has occurred that one is made aware
that the service life has been exhausted.
Important notice: to prevent costly repairs or possible water damage we strongly
recommend that the bowl or sump of all plastic housings be replaced periodically:
every 5 years for clear sumps, and every 4 years for opaque sumps. If your sump has
been in use for more than the recommended period, it should be replaced immediately.
Be sure to date any new or replacement sump for future reference and indicate the next
recommended replacement date.
Warranty: limited three (3) year warranty from the date of sale for material defects only.
Warranty is limited to repair or replacement of product only. Any misuse, misinstallation,
lack of maintenance, exceeding maximum pressure or failure to follow these instructions
will void limited warranty.
DISCLAIMER OF WARRANTIES. Except as expressly warranted in writing by hydronix
water technology, the goods sold by hydronix water technology are purchased by
the buyer “as is.” Hydronix water technology does not warrant that the goods are of
merchantable quality or that they can be used for any particular purpose. Except as
expressly warranted in writing by hydronix water technology, hydronix water technology
makes no representation or warranty of any kind with respect to the products.
LIMITATION OF LIABILITY. In no event shall hydronix water technology be liable to the
purchaser or any other entity for more than the invoice price received by hydronix water
technology for any non-conforming products. Hydronix water technology shall not be
liable to the purchaser or any other entity for personal injury, property damage, or any direct,
indirect, special, incidental, consequential, punitive, exemplary, or other damages of
any kind, including without limitation the cost of procurement of substitute goods, the
loss of pro ts, products, or production, or the interruption of business, however caused
and on any theory of liability, and whether or not hydronix water technology has been
advised of the possibility of such damages. The essential purpose of this provision is
to limit the liability of hydronix water technology arising out of the sale of products to
the purchaser whether for breach of contract, negligence, or otherwise. These limitations
shall apply notwithstanding any failure of essential purpose of any limited remedy
and not withstanding the provisions of any other agreement between hydronix water
technology and the purchaser.
Installation Guidelines
Model # Guide
HF 2-5 WH WH 14
Filter
Housing
Body
Length
Cap
Color
Body
Color
Connection
Type
Housing
Style
Housing Style: 2 = Slim Flat
Cap
Body/Cartridge
Length: 5 = 5”
10 = 10”
Body Color: WH -White
CL - Clear
BL - Blue
Cap Color: WH - White
BK - Black
Connection Type:
14 = 1/4”
38 = 3/8”
12 = 1/2”
LEGEND