Install Instructions

ManualsBrandsHydrolevel ManualsHeating SuppliesWire Harness for Connecting Safgard 1100 to Burnham CHG, SCG, PVG, Crown Bimini

126 Bailey Road, North Haven, CT 06473 • Phone (203) 776-0473 • FAX (203) 764-1711 • www.hydrolevel.com

1. Disconnect boiler wire harness from the

“SECONDARY” port on the Integrated Control

Module .

2. Plug into female plug adapter on #45-348 Wire

Harness .

3. Plug male adapter on #45-348 Wire Harness

into “SECONDARY” port on the Integrated

Control Module .

#45-348 Wire Harness

For use with Safgard Model 1100 Low Water Cut-Off on boilers equipped with United Technologies

Integrated Boiler Control Module

#45-348 Wire Harness

For boilers equipped with Honeywell Integrated Boiler Control Module

Wire Harnesses

MODEL 45-348

MODEL 45-349

MODEL 45-350

MODEL 45-353

Model 1100-H2

includes Low Water Cut-Off

and #45-348 Wire Harness







#45-348 Wire Harness

(available separately)

Wire harnesses on this sheet are available separately or

can be ordered with the Safgard Model 1100 low water cut-off.

See each listing below.

1. Disconnect boiler wire harness from the

“SECONDARY” port on the Integrated

Control Module  and plug into female plug

adapter on #45-348 Wire Harness .

2. Plug male adapter on #45-348 Wire Harness

into “SECONDARY” port on the Integrated

Control Module .

3. Plug the other end of the Wire Harness into

the Model 1100 low water cut-off .

#45-348

Wire

Harness

Model 1100

(available separately)









Summary of content (4 pages)

PAGE 1
Wire Harnesses MODEL MODEL MODEL MODEL Wire harnesses on this sheet are available separately or can be ordered with the Safgard Model 1100 low water cut-off. See each listing below. 45-348 45-349 45-350 45-353 #45-348 Wire Harness For use with Safgard Model 1100 Low Water Cut-Off on boilers equipped with United Technologies Integrated Boiler Control Module 1. Disconnect boiler wire harness from the “SECONDARY” port on the Integrated Control Module . 2.
PAGE 2
#45-349 Wire Harness For use with Safgard Model 1100 Low Water Cut-Off on boilers equipped with Weil McLain “U Control” Model 1100-H5 includes Low Water Cut-Off and #45-349 Wire Harness #45-349 Wire Harness (available separately) 1. Remove the factory installed Molex jumper from plug P12 on the “U Control” panel and plug in the Safgard Wire Harness . 2. Plug the other end of the Wire Harness into the Model 1100 low water cut-off .
PAGE 3
#45-349 Wire Harness For use with Safgard Model 1100 Low Water Cut-Off Model 1100-H5 includes Low Water Cut-Off and #45-349 Wire Harness #45-349 Wire Harness (available separately) Install the Safgard Model 1100 low water cut-off in the boiler or boiler piping as described in the installation instructions. 1. Remove the jumper installed in the boiler’s low water cut-off plug receptacle and plug in the 42" Safgard Wire Harness . 2.
PAGE 4
#45-353 Wire Harness For boilers equipped with United Technologies Integrated Boiler Control Module 1. Disconnect boiler wire harness from the Vent Damper port on the Integrated Control Module and plug into female plug adapter on #45-353 Wire Harness . 2. Plug male adapter on #45-353 Wire Harness into Vent Damper port on the Integrated Control Module . 3. Plug the other end of the Wire Harness into the Model 1100 low water cut-off .