Instructions / Assembly

1525 South Gladiola Street, Suite 8, Salt Lake City, UT 84104 • www.GetNewLook.com

NewLook® International, Inc. HydroHalt™

NewLook International, Inc. HydroHalt is a waterproofing and vapor retarding membrane for waterproofing a variety of

architectural surfaces, including concrete, masonry, wood, block, and metal. HydroHalt is designed specifically for subterranean

(below grade) foundation walls and other applications, such as decks, walls (both negative and positive side) and water

retainment structures. Use HydroHalt in conjunction with mesh or mat material for repairing cracks, joints and spalled areas.

USES & BENEFITS

• Waterproofing and vapor retarding (barrier) for architectural surfaces

• Waterproofing adhesive for protection/insulation board or tile

• Base coat for other water-based surface wearing products; no maintenance required!

• Non-hazardous, non-toxic, and non-flammable (VOC Compliant); user and eco-friendly

• Excellent elongation and recover

• Good tensile strength

• Exceptional bonding; won’t delaminate from surfaces

• Not affected by ponded water

• Water-based; may be applied to green or uncured concrete and to damp surfaces

PROPERTIES

Typical Uncured Properties Test Method Unit

Specific Gravity 1.034

Viscosity 9m-13m centipoise

pH 11.5 pH

Flammability 270° F

Color Brown to Black

Non-Toxic No Solvents

Shelf Life 6 months

Initial Cure 30 minutes

Final Cure 24-48 hours

Tensile Strength ASTM 412 32 psi

Elongation ASTM 412 3,860%

Resistance to Decay ASTM E 154 Section 13 9% Perm Loss

Accelerated Aging ASTM G 23 No Effect

Moisture Vapor Transmission ASTM E 96 0.071 g/sq. ft./hr.

Hydrostatic Water Pressure ASTM D 751 28 psi

Perm Rating (US Perms) ASTM E 96 0.17

Methane Transmission Rate ASTM D 1434 0

Adhesion to Concrete & Masonry ASTM C 836 7 lbf./inch

Hardness ASTM C 836 85

Crack Bridging ASTM C 836 No Cracking

Low Temperature Flexibility ASTM C 836-00 No Cracking at -20°

Resistance to Acids:

Acetic 30%

Sulfuric and Hydrochloric 15%

PAGE 1
NewLook® International, Inc. HydroHalt™ NewLook International, Inc. HydroHalt is a waterproofing and vapor retarding membrane for waterproofing a variety of architectural surfaces, including concrete, masonry, wood, block, and metal. HydroHalt is designed specifically for subterranean (below grade) foundation walls and other applications, such as decks, walls (both negative and positive side) and water retainment structures.
PAGE 2
COVERAGE 60-mils wet (to achieve 40-mils cured): 28 square feet per gallon 90-mils wet (to achieve 60-mils cured): 19 square feet per gallon LIMITATIONS • • • • • • • Should be applied to clean and dry surfaces Adjacent areas and surfaces should be protected from contact with HydroHalt HydroHalt be stored above 40° F A test area, mock-up or representative jobsite sample should always be provided to verify compatibility of substrate Solvent-based products should not be applied over HydroHalt During warm we
PAGE 3
Store HydroHalt in a dry place and in temperatures above 40° F. LIMITED PRODUCT WARRANTY This product is warranted to be of uniform quality within manufacturer’s tolerances. NewLook International, Inc. has no control over the use of HydroHalt (“Product”), therefore no other oral or written representation or statement of any kind, express or implied, now or hereafter made is authorized or warranted by NewLook or its affiliates, and NewLook and its affiliates hereby disclaims all such warranties.