W28 Ring Scanner Product Specification www.hycoiot.
W28 Series Product 2D Ring Scanner Product Specification Disclaimer Disclaimer @ 2018 Shanghai Hyco Genyong Technology Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or remove the seal label from the device. Otherwise, Shanghai Hyco Genyong Technology Co., Ltd.
W28 Series Product 2D Ring Scanner Product Specification The products depicted in this manual may include software copyrighted by Shanghai Hyco Genyong Technology Co., Ltd. or a third party. The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior written consent from the copyright holders. This manual is copyrighted.
W28 Series Product 2D Ring Scanner Product Specification Menu Overview .............................................................................................................................. 3 Product Features ............................................................................. 错误!未定义书签。 Product advantage .......................................................................... 错误!未定义书签。 Product demostration ......................................................................
W28 Series Product 2D Ring Scanner Product Specification Overview In addition to extract price information at the checkout counter in supermarkets, the purpose of scanning barcodes/2D codes/RFID in the express delivery, logistics, supply chain, food and drug tracing management, intelligent manufacturing and other fields is for responsibility division, which is intended to function as an electronic signature in each shift.
W28 Series Product 2D Ring Scanner Product Specification Ultra-low power consumption and green Light, flexible, ease of use Reinforce brand identity with customers Recognize codes on multiple materials Rich accessories Product demonstration Ring Scanner Scan Window Left touch button Ring strap Front view Indicator Light Right touch button 5
W28 Series Product 2D Ring Scanner Product Specification Back view How to wear The wearing method of this product is shown in the picture 1 below. The product can be worn on the third joint of the index finger of the left or right hands to adapt to the tightness of the ring strap. If it feels too tight or too loose, you can replace the silicone ring strap with an appropriate size.
W28 Series Product 2D Ring Scanner Product Specification Figure 1 How to charge Connect the charging cradle to the power source, and place the Scanner into the charging cradle as shown in Figure 2 (the scanning lens of the Scanner is upward), and then charging starts. The charging status indicator turns red to indicate that it is charging, and green to indicate that the battery is fully charged, and charging is complete.
W28 Series Product 2D Ring Scanner Product Specification ★ In order to avoid triggering the light when taking out the Scanner from the charging cradle and directing the eyes to cause injury. Therefore, it is set that after the Scanner is charged, it needs to touch three times in a row to emit light normally.
W28 Series Product 2D Ring Scanner Product Specification Working Indicating LED: Red – Power-up Green – In operation Charging & Bluetooth Indicating LED: Red – Charging and Bluetooth disconnection Blue – Bluetooth connection, no charging or charging finished Purple – Charging and Bluetooth connection Green – Fully charged or no charging Charging thorugh C20 Charging Station C20 charging station Charging Indicator light Picture 3 Download C20 specification sheet through：http://www.hycoiot.com/C20.
W28 Series Product 2D Ring Scanner Product Specification Replacing the ring strap This product is equipped with 1 silicone ring strap, and 5 different kinds of spare silicone ring straps to adapt to different finger sizes. You can contact HYCO Technology Customer Service Center to purchase additional ring straps as a spare. Figure 4 How to replace the ring strap You can complete the replacement as shown in Figure 5.
W28 Series Product 2D Ring Scanner Product Specification Figure 5 ring strap haven’t push to the end of the slot and affects charging Figure 6 Specifications Physical characteristics Dimension 38.6mm*29.0mm*22.1mm （ ring strap not include） Weight 20g（ring strap not include） Material Shell of scanner： PC+ ABS Ring strap ：Silicone Rubber Use environment Ambient light Indoor (artificial light): less than 4,842 lx Outdoor (daylight): less than 86,111 lx Working Temp.
W28 Series Product 2D Ring Scanner Product Specification Parameter fill-in light White LED Aim "+" pattern 650nm laser diode Scan speed 60 frames/sec Scan angle Horizontal angle 32.5 ° , vertical angle 21.
W28 Series Product 2D Ring Scanner Product Specification Ingress protection IP66 Within the applicable temperature range, it can withstand 12 drops from a height of 3 Anti-drop/roll-off meters to the concrete floor; performance According to IEC 60068-2-32 standard, it can withstand more than 1,000 rolls (0.5 meters) Antistatic ability Battery ±30 KV air static electricity, ±25 KV contact static electricity 3.
W28 Series Product 2D Ring Scanner Product Specification International CE，FCC certification ★ The technical specifications of this product are subject to change without notice.
W28 Series Product 2D Ring Scanner Product Specification Vibration reminder Vibration reminder function default turns on, this function can be turn on/off through scan below function code. 开启振动 Turn on vibration reminder 关闭振动 Turn off vibration reminder Remind type Turn on the vibration function (default) Turn off vibration 1 short vibration Description After turning on this function, if the barcode is correctly identified, it will vibrate. The vibration time is 70 milliseconds.
W28 Series Product 2D Ring Scanner Product Specification Scan angle When scanning the bar code, the light-emitting surface should be perpendicular to the paper surface as a reference, within the range of the pitch deflection angle ±65°, and the tilt deflection angle ±50°, the scan line completely crosses the barcode area, and there is enough white space on the left and right sides.
W28 Series Product 2D Ring Scanner Product Specification Figure 6 The scannable field of view of this product is a rectangular divergent area, with a horizontal field angle of 32.5゜ and a vertical field angle of 21.4゜.
W28 Series Product 2D Ring Scanner Product Specification 5mil 6 18.5 10mil 7.5 33.5 Code128A UPCA 100% 5.5 28.5 123ABC 20mil 12 50 40mil 21 81 50mil 29 98 10mil 3.5 13.5 14mil 3 18 8 20mil 3 25 Data Matrix 10mil 4 8.5 63234604655469 14mil 4 12 8 20mil 4 20 QR Code 63234604655469 Note: 1. The average reflection difference (MRD) of the barcode is more than 80%; 2.
W28 Series Product 2D Ring Scanner Product Specification Update scanner firmware This product supports two ways to update the firmware: 1. Use Android mobile devices (such as mobile phones, tablets, etc.) to update product firmware. Install the "HYCO" APK on the android device; Open the APK and select the "software upgrade" function; Follow the prompts to transfer the scanner firmware.
W28 Series Product 2D Ring Scanner Product Specification www.hycoiot.com. Or contact Hao Chuang Technology Customer Support Center.
W28 Series Product 2D Ring Scanner Product Specification Ring Strap 10 个 5 different size Certificate of conformity 1 Certificate of conformity for the product User manual 1 Product using guide If there is any non-compliance, please contact HYCO Technology Customer Support Center or call the customer service hotline 4006-305-758. Battery Safety Guide There should be no debris, combustibles, or chemicals in the charging area of the device.
W28 Series Product 2D Ring Scanner Product Specification The heavy impact caused by any device using the battery falling on a hard surface may cause the battery to overheat. Do not short-circuit the battery, or use metal or other conductive objects to touch the battery terminals.
W28 Series Product 2D Ring Scanner Product Specification Appendix Function setting barcode Common Setting 【Equipment inform】 Scan below barcode to get device inform when successful connect to terminals 设备信息输出 【Restore factory setting】 Scan below barcode to restore factory setting, The device will disconnect from the cradle, and the identifiable code system and Bluetooth name will be restored to the default factory settings.
W28 Series Product 2D Ring Scanner Product Specification 【Turn on/off vibration】 Scan below barcode to turn on/off vibration 开启振动 Turn on vibration 关闭振动 Turn off vibration Add Enter/Tab After scan “Add Enter” barcode, it can automatically move to next line in the text field after each scanning. If user wants to close the function, scan “Delete Enter” barcode. 添加回车换行 Add Enter 删除回车换行 Delete Enter After scan "Add the tab" barcode, it can automatically move to next line in excel after each scanning.
W28 Series Product 2D Ring Scanner Product Specification 添加制表符 Add the Tab 删除制表符 Delete the Tab Trigger mode setting 【Automatic interval scanning】 After scan "Automatic interval scanning" bar code, ring could automatically scan every 0.5 ~ 3 seconds 自动间隙连续扫描 without touching (2 seconds by default) 【Triggered continuous scanning】 Scan the barcode “Triggered continuous scanning”, ring could keep scanning when user keeps touching the ring.
W28 Series Product 2D Ring Scanner Product Specification scan once. User can switch to this model by scan below barcode. 手动触发扫描 Turn on/off identifiable symbology Scanning the corresponding barcode can turn on/off the identification of different types of barcodes, and turn off unnecessary symbologies, which can reduce the error rate of barcodes and increase the scanning speed to a certain extent.
W28 Series Product 2D Ring Scanner Product Specification 【Turn on/off CODE39】 开启 CODE39 Turn on CODE39 关闭 CODE39 Turn on CODE39 Decode digits setting Limit the number of digits for identifying barcodes, and barcodes below the HYCO set digits/higher than the maximum set digits will not be recognized. The default length is 2 to 50 digits, the HYCO can be 1 digit, and the maximum can be 99 digits.
W28 Series Product 2D Ring Scanner Product Specification Scan [Restore factory setting] barcode switch back to default setting Sample ： Set Code39 code HYCO recognition 3 digits maximum recognition 20 digits 最小 CODE39 ① HYCO CODE39 数字条码 3 ② digit 3 确认长度设置 ③ confirm HYCO setting complete 最大 CODE39 ① maximum CODE39 数字条码 2 ② Digit 2 28
W28 Series Product 2D Ring Scanner Product Specification 数字条码 0 ③ digit 0 确认长度设置 ④ confirm Setting completed 【digit setting function code】 Code39 setting code 最小 CODE39 Minimum CODE39 最大 CODE39 Maximum CODE39 Code128 digit setting code 最小 CODE128 Minimum CODE128 29
W28 Series Product 2D Ring Scanner Product Specification 最大 CODE128 Maximum CODE128 Digital barcode barcode 数字条码 0 Digital barcode 0 数字条码 1 Digital barcode 1 数字条码 2 Digital barcode 2 数字条码 3 Digital barcode 3 数字条码 4 Digital barcode 4 30
W28 Series Product 2D Ring Scanner Product Specification 数字条码 5 Digital barcode 5 数字条码 6 Digital barcode 6 数字条码 7 Digital barcode 7 数字条码 8 Digital barcode 8 数字条码 9 Digital barcode 9 Confirm/cancel setting barcode 确认长度设置 Confirm length setting 31
W28 Series Product 2D Ring Scanner Product Specification 取消长度设置 Abolish length setting Preamble barcode output setting 开启 EAN13前导码输出 Turn on EAN13 Preamble barcode output 关闭 EAN13前导码输出 Turn off EAN13 Preamble barcode output supplemental barcode output setting 开启 EAN13/EAN8补码输出 Turn on EAN13/EAN8 supplemental output 关闭 EAN13/EAN8补码输出 Turn off EAN13/EAN8 supplemental output 32
W28 Series Product 2D Ring Scanner Product Specification 自动 EAN13/EAN8补码输出 Automatic EAN13/EAN8 supplemental output FULL ASCII Setting 开启 CODE39FULL ASCII Turn on CODE39FULL ASCII 关闭 CODE39FULL ASCII Turn off CODE39FULL ASCII Bluetooth disconnect alarm setting barcode Turn on the Bluetooth disconnection alarm, which can continuously remind the operator when the Bluetooth connection has been disconnected, which is convenient for timely processing.
W28 Series Product 2D Ring Scanner Product Specification 关闭蓝牙断开报警 Turn off Bluetooth disconnect alarm After turning on the Bluetooth disconnection alarm, when the Bluetooth is disconnected, the blue light of the ring flashes + vibrating prompt, which will continue this state; there are two ways to turn on or turn off the function: ① Use the communication command, ②Scan the barcode for the specified setting. After the Bluetooth connection is successful, it prompts to terminate.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
W28 Series Product 2D Ring Scanner Product Specification Manufacturer's Name: Shanghai Hyco Genyong Technology Co., Ltd. Sample Description: Room 105, 1/F, Building B, No.999 of Huaxu Road, Qingpu District, Shanghai, China. Trade Mark: HYCO Model number: W28 Operating Temperature: ‐10° C to 40° C This device was tested for typical body‐worn operations.
