Instructions / Assembly

ManualsBrandsHY-C ManualsBuilding materials6 ft. Extension Kit for GutterSweep Rotary Gutter Cleaning System

GutterSweep

Rotary Gutter Cleaning System

Operator’s Manual

Thank you for purchasing the

GutterSweep

™

Rotary Gutter Cleaning System.

Please follow the important safeguards and operating instructions included within this

manual to enjoy the benefits and safe operation of the

GutterSweep

™

System.

BEFORE

AFTER

Accessories

Included

Rotary Paddle Brush

Gutter Brush with Water

Jet Nozzle

Gutter Scoop with Water Jet Nozzle

Digital Camera Mount—

inspect gutters before

and

after cleaning

(

Camera not included)

Works with your cordless drill

™

Summary of content (8 pages)

PAGE 1
GutterSweep ™ Rotary Gutter Cleaning System Operator’s Manual Thank you for purchasing the GutterSweep™ Rotary Gutter Cleaning System. Please follow the important safeguards and operating instructions included within this manual to enjoy the benefits and safe operation of the GutterSweep™ System.
PAGE 2
Important Safeguards > Read all safety & operating instructions before use. > All warnings in the manual must be strictly adhered to. > Failure to comply with the safety and operating instructions may result in property damage or personal injury. > Retain the operator’s manual for future use. > Not all gutters can be cleaned from the ground level. In some cases, the gutter opening may be too narrowor the debris too compacted to remove with the GutterSweep™ Tools.
PAGE 3
Table of Contents What’s Included 1. Rotary Drive Extension Poles 2 2. Rotary Paddle Brush Getting Started .............................................................. 4 Cleaning Gutters with Rotary Paddle Brush ............... 5–6 Cleaning Gutters with Non-Rotary Tools ....................... 7–8 Cleaning Gutter Exterior .............................................. 8 Additional Applications ................................................... 8 3. Gutter Brush with Water Jet Nozzle 4.
PAGE 4
Getting Started Assembling Tool for Rotary Gutter Cleaning Step 1. Connect Pole Sections: > Loosen coupling nut slightly on lower pole section (Do Not Remove Coupling Nut). > Depress button on pole to be connected and slide into Coupling. Be sure upper pole section is locked into place by rotating section until button locks into sleeve. > Hand tighten threaded coupling nut. Step 2. Attach Curved Tube: > Connect Curved Tube by sliding into top pole section using the same method as described above.
PAGE 5
Determine Type of Build-Up in Gutters Step 1. Once the tool is assembled, use the “Camera Mount” with your digital camera to get a photo or short video of your gutters “Before & After” cleaning. This will help determine what type of debris is in the gutter and what cleaning attachment to choose for the job. Important Note: Do Not use your camera while cleaning as it may cause permanent damage to your camera. Gardus accepts no liability for damage to your camera. Step 2.
PAGE 6
Rotary Gutter Cleaning (cont.) Step 2. Cleaning Around Gutter Supports: Important Note: Use caution while spinning Paddle Brush near gutter supports. Operate drill at half speed or less especially while cleaning under supports. 1) Clean completely under the support until the Curved Tube makes contact with the gutter support. 2) Pull the Paddle Brush back slightly and lift up and over gutter support. 3) Lower the Paddle Brush back into the gutter and continue cleaning. Step 3.
PAGE 7
Cleaning with Non-Rotary Attachments Remove and Rinse Cleaning with the Gutter Brush and Gutter Scoop Step 1. Determine Type of Build-up in Gutters Attach Grip Handle to end of base pole section facing up as shown > Refer to page 4 Step 2: Connect as many pole sections as needed to reach desired gutter height. Note: A 6 ft. Extension Kit is available and sold separately.
PAGE 8
Cleaning with Non-Rotary Attachments Step7. Collect Debris on Tarp and Dispose: It’s best to clean the ground area before rinsing the gutter clean with water. Step 8. Rinsing the Gutter: Connect garden hose to Water Control Valve then connect Water Control Valve to bottom pole section and turn water on. Use the Gutter Brush or Gutter Scoop with built in water jet nozzle to rinse the inside and outside of the gutter clean.