CRT1350LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers TRAINING • • • • • Read the Owner’s Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction. Keep the area of operation clear of all persons, particularly small children, and pets.
PRODUCT SPECIFICATIONS Gasoline Capacity: Unleaded Regular 3 Quarts (2,8L) OIL (API-SG-SL): (Capacity 20 oz/0,6L) Spark Plug: SAE 30 Above 32°F/0°C SAE 5w30 Below 32°F/0°C Champion RC12YC (Gap: .030"/0.76mm) CUSTOMER RESPONSIBILITIES • • • Read and observe the safety rules. Follow a regular schedule in maintaining, caring for and using your tiller. Follow instructions under “Maintenance” and “Storage” sections of this Owner’s Manual.
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY FRONT A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY UNPACKING CARTON (See Fig. 2) • CAUTION: Be careful of exposed staples when handling or disposing of cartoning material. Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. HANDLE ASSEMBLY "UP" POSITION IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES.
ASSEMBLY CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) • • • Hook spring of clutch cable through hole in control bar bracket. CONTROL BAR BRACKET Insert end of shift rod into hole of shift lever indicator. Insert hairpin clip through hole of shift rod to secure. SHIFT ROD SHIFT LEVER INDICATOR HAIRPIN CLIP CONTROL BAR CLUTCH CABLE CONTROL BAR BRACKET Fig. 7 REMOVE TILLER FROM CRATE • END OF CLUTCH CABLE • Fig. 6 • Make sure shift lever indicator is in “N” position (See Fig.
OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning.
OPERATION 00155 The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine. SHALLOWEST TILLING (CULTIVATING) STOPPING (See Fig.
OPERATION • When you have completed your turn-around, release the drive control bar and lower handle. Place shift lever in till position and move throttle control to desired speed. To begin tilling, hold drive control bar against the handle. ADD GASOLINE • TO TRANSPORT CAUTION: Before lifting or transporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.
OPERATION • When engine starts, slowly move choke control to "RUN" position as engine warms up. NOTE: A warm engine requires less choking to start. • Move throttle control to desired running position. • Allow engine to warm up for a few minutes before engaging tines. NOTE: If at a high altitude (3000 feet) or in cold temperatures (below 32°F), the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual.
MAINTENANCE ER EV EV ER Y2 5H OU RS Y5 0H EV OU ER YS RS EA SO N UR HO CH Y5 EA ER RE EV FO BE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE S US E MAINTENANCE SCHEDULE SERVICE DATES Check Engine Oil Level Change Engine Oil 1,2 Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge 2 Clean Engine Cylinder Fins Replace Spark Plug RH Gear Case Grease Fitting (1oz.
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SG-SL.
MAINTENANCE SPARK PLUG COVER KNOB Replace spark plugs at the beginning of each tilling season or after every 50 hours of use, whichever comes first. Spark plug type and gap setting is shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual. COVER FOAM PRECLEANER AIR CLEANER CARTRIDGE TRANSMISSION Once a season, lubricate the right hand side gear case grease fitting with 1 oz. of EP #1 Grease. BASE CLEANING Do not clean your tiller when the engine and transmission are hot.
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. • First loosen handle lock lever. • Handle can be positioned at different settings between “HIGH” and “LOW” positions. • Retighten handle lock lever securely after adjusting.
SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT (See Fig. 23) • • • • • • GROUND DRIVE BELT ADJUSTMENT (See Fig. 23) Remove belt guard (See “TO REMOVE BELT GUARD” in this section of this manual). Remove old belt by slipping off engine pulley first then remove from transmission pulley. Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES. Check belt adjustment as described below. Replace belt guard.
SERVICE AND ADJUSTMENTS TINE REPLACEMENT (See Figs. 24, 25 and 26) • CAUTION: Tines are sharp. Wear gloves or other protection when handling tines. • A badly worn tine causes your tiller to work harder and dig more shallow. Most important, worn tines cannot chop and shred organic matter as effectively nor bury it as deeply as good tines. A tine this worn needs to be replaced.
SERVICE AND ADJUSTMENTS ENGINE TO ADJUST CARBURETOR The carburetor has been preset at the factory and adjustment should not be necessary. However, engine performance can be affected by differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, contact your nearest authorized service center/department IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS.
STORAGE Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual). WARNING: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION 1. 2. 3. 4. 5. Out of fuel. Engine not “CHOKED” properly. Engine flooded. Dirty air cleaner. Water in fuel. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Clogged fuel tank. Loose spark plug wire. Bad spark plug or improper gap. Carburetor out of adjustment. Oil soaked air filter. 6. 7. 8. 9. 10. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Clean or replace air cleaner cartridge.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 HANDLE ASSEMBLY 8 6 2 30 12 13 33 2 10 14 11 41 27 15 27 1 29 37 21 16 37 4 20 19 18 32 26 24 17 11 23 31 Handle_assy_99_20.euro KEY NO. PART NO.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 MAINFRAME, LEFT SIDE 7 6 9 8 39 10 62 5 68 42 12 18 13 16 14 27 18 37 19 15 32 17 18 29 15 15 30 54 28 3 23 17 15 63 64 24 15 4 26 25 mainframe_left_20.euro KEY NO. PART NO.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 MAINFRAME, RIGHT SIDE 15 1 14 16 44 19 18 20 17 44 44 22 44 13 7 8 21 12 7 21 9 8 9 mainframe_right_18_r1 11 KEY NO. 1 7 8 9 11 12 13 14 15 PART NO. 532 17 56-24 532 18 02-75 810 04 06-00 873 22 06-00 532 12 49-61 532 00 49-29 532 00 50-15 532 00 50-14 532 12 47-18 873 97 05-00 – – – – – – – KEY NO. 16 17 18 19 20 21 22 44 DESCRIPTION Bumper Counter Weight, R.H.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 TRANSMISSION KEY NO. PART NO. -1 532 18 13-37 Transmission Assembly 532 18 13-32 Gearcase, R.H. w/Bearing (Includes Key No. 18) 532 18 13-62 Spacer Gearcase 532 17 50-35 Gear Reverse 532 10 53-45 Gear, Cluster, Red 1st & 2nd 532 10 04-13 Bearing, Needle 532 14 45-64 Sprocket and Tine Assembly 532 14 45-63 Sprocket Assembly w/Bearing (Includes Key No.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 TINE SHIELD TINE?SHIELD? ? ?IN?R KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 18 19 20 PART NO.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 TINE ASSEMBLY ! ! ! " " ! " " " " " ! " " " " " " " " " ! ! ! ! KEY NO. 1 3 4 5 6 7 8 PART NO. 532 00 65-56 532 10 11-94 532 12 46-60 532 18 93-59 873 61 06-00 810 04 06-00 874 61 06-16 DESCRIPTION Tine, Outer, L.H. Tine, Inner, L.H.
REPAIR PARTS TILLER - - MODEL NO. CRT1350LS (96093001602), PRODUCT NO. 960 93 00-16 DECALS 1 2 4 6 5 3 8 7 KEY NO. 1 2 3 4 5 6 7 8 --- PART NO.
SERVICE NOTES 27
04.21.11 CL Printed in the U.S.A.
