Operators Manual
Table Of Contents
- Simboli
- Indice
- Prima dell’avviamento osservare quanto segue:
- Alla gentile clientela
- Importante
- Abbigliamento protettivo
- Dispositivi di sicurezza della macchina
- Attrezzatura di taglio
- Montaggio del manubrio e impugnatura dell'acceleratore
- Montaggio della lama e della testina portafilo
- Montaggio della protezione per il trasporto
- Come indossare l’imbracatura ed agganciare il decespugliatore
- Carburante
- Carburante
- Rifornimento
- Controlli prima dell’avviamento
- Avviamento e arresto
- Istruzioni generali di lavoro
- Carburatore
- Filtro dell’aria
- Filtro del carburante
- Riduttore angolare
- Candela
- Schema di manutenzione
- Caratteristiche tecniche
- Dichiarazione di conformità CE
- Símbolos
- Índice
- Antes de arrancar, observe lo siguiente:
- Apreciado cliente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del manillar y la empuñadura de acelerador
- Montaje de la hoja y del cabezal de corte
- Montaje de la protección para transportes
- Ajuste del arnés y la desbrozadora
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Filtro de aire
- Filtro de combustible
- Engranaje angulado
- Bujía
- Programa de mantenimiento
- Datos técnicos
- Declaración CE de conformidad
- Símbolos
- Índice
- Antes de arrancar, observe o seguinte:
- Prezado cliente!
- Importante
- Equipamento de protecção pessoal
- Equipamento de segurança da máquina
- Equipamento de corte
- Montagem da direcção e do punho do acelerador
- Montagem da lâmina e cabeçote de recorte
- Montagem da protecção para transporte
- Ajuste do suporte e do roçador
- Segurança no manejo de combustível
- Combustível
- Abastecimento
- Controlo antes de arrancar
- Arranque e paragem
- Instruções gerais de trabalho
- Carburador
- Filtro de ar
- Filtro de combustível
- Engrenagem angular
- Vela de ignição
- Esquema de manutenção
- Especificações técnicas
- Certificado CE de conformidade
- Symbols
- Contents
- Note the following before starting:
- Dear Customer,
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Assembling the handlebar and throttle
- Fitting blades and trimmer heads
- Fitting the transport guard
- Adjusting the harness and brush cutter
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburettor
- Air filter
- Fuel filter
- Bevel gear
- Spark plug
- Maintenance schedule
- Technical data
- EC-declaration of conformity
120 – English
TECHNICAL DATA
EC-declaration of conformity
(Applies to Europe only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the brush cutters Husqvarna
233R, 243R and 253R
with serial numbers dating from 2011 onwards (the year is clearly stated on the rating plate,
followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:
- of May 17, 2006 "relating to machinery" 2006/42/EC
- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
- of May 8, 2000 ”relating to the noise emissions in the environment”
2000/14/EC. Conformity assessment according
to Annex V. For information relating to noise emissions, see the chapter Technical data.
The following standards have been applied: EN ISO 12100-2:2003, CISPR 12:2005, EN ISO 11806:1997
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type
examination on behalf of Husqvarna AB. The certificates are numbered:
SEC/11/2317 - 233R, SEC/11/2318 - 243R,
SEC/11/2319 - 253R
Huskvarna 30 June 2011.
Bengt Frögelius, Development manager (Authorized representative for Husqvarna AB and responsible for technical
documentation.)
H1154201-30,233,243,253,R.fm Page 120 Tuesday, July 5, 2011 4:18 PM