Instructions / Assembly
Each tool is packed with an anti-dust cap on the air connector,
Keep the anti-dust cap cover the air connector
when the tool is not in use.
checkitafterunpacking.
ANTIDUST-
Do not at any time let brake fluids,
gasoline, petroleum-based products,
penetration oils, ect., come in contact
with plastic parts. Chemicals can
damage, weaken or destroy plastic
which may result in serious personal
injury.
WARNING:
!
Do not store tools in a cold weather
environment to prevent frost or ice
formation on the tool's operating valves
and mechanisms that could cause tool
failure.
CAUTION:
COLD WEATHER OPERATION
For cold weather operation, near and below
freezing, the moisture in the air line may freeze
and prevent tool operation. We recommend the
use of air tool lubricant or permanent antifreeze
(ethylene glycol) as a cold weather lubricant.
RECOMMENDED HOOKUP
TROUBLE SHOOTING
Stop using tool immediately if any of
the following problems occur.
Serious personal injury could result.
Any repairs or replacements must be
done by a qualified service person or
an Authorized service center.
WARNING:
!
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and maybe
damaged by their use. Use clean cloths to
remove dirt, dust , oil, grease, etc.
CLEANING
The air compressor must be able to maintain a minimum of 80 psi when the tool is being used. An
inadequate air supply can cause a loss of power and inconsistent driving.
An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid
and solid impurities which can rust or gum up internal parts of the tool.
Always use air supply hoses with a minimum working pressure rating equal to or greater than the
pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 3/8" air hose
for runs up to 50'. Use 1/2" air hoses for 50' run or longer. For better performance, install a 3/8" quick
plug (1/4" NPT thread) with an inside diameter of .315" (8mm) on the tool and 3/8" quick coupler on
the air hose.
Use a pressure regulator on the compressor, with an operating pressure of 0-125 psi. A pressure
regulator is required to control the operating pressure of the tool between 80 and 100 psi.
1.
2.
3.
4.
The air compressor must be able to maintain a
minimum of psi when the tool is being used.
An inadequate air supply can cause a loss of
power and inconsistent driving.
80
CAUTION:
WARNING:
!
Do not connect with an air compressor which can
potentially exceed 200psi. As tool may burst,
possibly causing injury.
Quick
coupler
Quick
connector
Air hose
Quick
connector
Oiler
Filter
Quick
connector
Regulator
Compressor
1009
Air leaking between
housing and cap
1. Loose screws in housing.
2. Damage to cap gasket.
1. Tighten screws.
2. Replace cap gasket.
Air leaking through cap
exhaust or nose area
1. Air escaping from tool.
2. Damaged O-Ring
1. Slap the cap side of the tool into the palm
of your hand with enough force to reset the
internal piston.
2. Replace O-rings.
CORRECTIVE ACTIONPROBLEMS
POSSIBLE CAUSE(S)
Nailer not setting
fastener completely
Nailer operates slowly
or has loss of power
1. Nail guide loose.
2. Inadequate air flow to nailer
1. Nailer not lubricated sufficiently.
2. Worn O-rings.
3. Low air pressure.
1. Tighten nose guide.
2. Check hose, fitting, or compressor.
1. Lubricate nailer.
2. Replace and lubricate O-rings.
3. Check and adjust pressure.
WARRANTY
2 YEARS LIMITED WARRANTY
If within two years from the date of purchase, this Husky air tool product fails due to a
defect in materials or workmanship, please immediately contact Product Support at
(8am to 5pm EST, M-F, except normal Holiday).Do not return the air
tool to the store. Please be prepared to send the product, postage prepaid, along with
a copy of the dated first owner purchase receipt with the toolmodelto: PRIME
GLOBAL PRODUCTS, INC. Address: . Adefectiveproduct
willbepromptlyreplacedwithanewoneofequalorgreatervalue. Thiswarranty
excludesincidental/consequentialdamagesandfailuresduetomisuse, abuseor
normalwearandtear. Thiswarrantygivesyouspecific rights, and you may also
have other rights, which vary, from state to state. Please call for
details.
1-866-676-8468
Ball Ground, Ga 30107
1-866-676-8468