Use and Care Manual

12
13
Operation(Continued)
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the tool fromthe air source.
Press theselectablefiringmode button, turningthe
selectablefiringmodeswitchinthedownwards position,
the firing mode indicator should be pointing at the multi-
nail icon.
Connect the tool to the air source.
Pull and hold the trigger with the tool off the work piece.
Press the work contact element against the work piece. A
nail will be driven.
The tool must be allowed to recoil away from the work
piece.
Move the tool along the work piece with a bouncing
motion. Each time the work contact element is depressed
a nail will be driven.
Assoonasthedesirednumberofnailshasbeendriven ,
removefingerfromtrigger .
Selectablefiring
mode button
Selectablefiringmode
switch in downwards
position
CONTACT ACTUATION MODE
Contactactuationallowsveryfastrepetitivefastener
placement .
To use the tool to drive nails in this actuation mode the work
contact element and trigger can be actuated in any order.
NOTE:
This actuation mode is recommended when less precise nail
placement is required.
Extreme care should be taken because a nails will be driven
when the work contact element is pressed against any
surface.
Since the tool can be actuated without removing the finger
from the trigger, this is considered to be a less restrictive
mode, suitable for more experienced users.
Maintenance
ANTI-DUST CAP
Each tool is packed with an anti-dust cap on the air
connector, check it after unpacking.
Keep the anti-dust cap covering the air connector when the
tool is not in use.
LUBRICATION
Lubrication is required for best performance after long
periods use. Oil for pneumatic fastening tools is added
through the air line connection and will lubricate internal
parts.
WARNING:Anytimeinspection, maintenance,and
cleaningaredone:
Disconnectthetoolfromtheairsource.
Emptythemagazinecompletely.
Turn the tool so the air inlet is facing up. Place 2 - 3 drops
of pneumatic fastening tool oil into air inlet. Do not use
detergent oils, oil additives, or air-tool oils asthese
lubricantswillcauseacceleratedweartothesealsand
bumpersinthetoolresultinginpoortoolperformance ,
andfrequenttoolmaintenance .
Disconnect the air supply from the tool to add the
lubricant.
After adding oil, connectthetooltotheairsourcerun ,
tool briefly. Wipe off any excess oil from the cap exhaust.
SEQUENTIAL FIRING MODE
Single sequential actuation provides the most accurate
fastener placement. This is considered to be more restrictive
mode of operation, suitable for less experienced users.
To use the tool to drive nails in this actuation mode, work
contact element and trigger must be used in a specific order.
Disconnect the tool fromthe air source.
Press theselectablefiringmode button, turningthe
selectablefiringmodeswitchintheupwards, the firing
mode indicator should be pointing at the single nail icon.
Connect the tool tothe air source.
Thework contactelement must be completely depressed
by placing the nose of the tool against the work piece.
The trigger must be pulled firmly and then released.
The tool must be allowed to recoil away from the work
piece.
To continue operation in a separate location, move the tool
along the work piece, repeating step 4 through 6.
Firing the tool
8
1.
2.
3.
4.
5.
6.
The tool is equipped with a trigger that select one of two
firing modes:
Selectablefiring
mode button
Selectablefiringmode
switch in upwards position
Note:
If the trigger is pulled before the work contact element is
depressed, the tool will not operate.
This is considered to be more restrictive mode of operation,
suitable for less experienced users.
WARNING: Remove the finger from the trigger when
not driving nails. Always carry the tool by the handle
only.
WARNING:An improperly functioning tool must not be
used. Do not actuate the tool unless the tool is placed
firmly against the work place.
WARNING:Always know the operational mode of the
tool before using. Failure to know the operational
mode could result in death or serious personal injury.
WARNING: Duringnormalusethetoolwillrecoil
immediatelyafterdrivingafastenerThisisanormal .
functionofthetoolDonotattempttopreventthe .
recoilbyholdingthetoolagainsttheworkRestriction .
oftherecoilcanresultinasecondfastenerbeing
drivenfromthetoolGripthehandlefirmlyandletthe .
tooldotheworkFailuretoheedthiswarningcan .
resultinseriouspersonalinjury .
WARNING:Thetoolmustbeallowedtorecoilaway
fromtheworkpiece. Do not drive a nail on top of
another nail.
Operation(Continued)