Installation Manual

ManualsBrandsHusky Liners ManualsAutomotiveHusky Liners 58446 Black Combo Custom Mud Guards 4 Pack

PART NO. 5844

5844 Front Instructions (2 SIDED DOC)F

Rev: 0

FORD F150

WITHOUT FENDER FLARES

FRONT MUD GUARD INSTALLATION INSTRUCTIONS

Install Paint Protection Film before mud guards (see other side)

Please read instructions thoroughly before installation.

Tools Required

• 1/8” drill bit / Drill

• Short #2 Phillips screwdriver

• Center punch

Package Contents

• Driver & passenger side front mud guard

• #10 SEM screw (qty. 2)

• U-clip (qty. 2)

• Paint Protection Film (1 set)

• Spring Clip (Qty 2)

• Instruction sheet

NOTE: Turn the front wheels all the way to the left or right for mud guard installation. However, it may be necessary

to remove the wheels depending on the tools being used for installation.

Determine which mudguard you have by locating the part number molded in the mounting flange

(5844 LH 5844 RH).

Clean and degrease the mud guard location area on the fender before installation.

2. Remove existing fasteners from location B and C.

3. Peel red protective cover from the 3M adhesive on the mudguard.

4. Attach mud guard to front fender with factory fasteners at location B and C, check fit and make sure mud guard is

parallel to ground before tightening. Be sure to press firmly on the area with the 3M adhesive tape to make sure

adhesive is set.

5. Install the spring clip over the mudguard and the fender lip at the location with the raised tic marks.

OPTIONAL FASTENER INSTALLATION

6. Using the mud guard as a template mark, center punch and drill 1/8” holes at location A.

7. Install #10 SEM screw through the mudguard and sheet metal and into the U-clip on the backside of the metal.

(Note: The U-clip dose not clip over the sheet metal, it acts as a nut on the backside of the fender lip)

PAINTING INSTRUCTIONS

Note: If painting mud guards, perform a mud guard test fit to ensure correct fit and application prior to painting.

1. Clean mud guard with a soap and water solution to remove dirt and other contaminates.

2. Sand painting surface with 320 grit sand paper.

3. Apply a coating of flexible primer-adhesion promoter.

Summary of content (4 pages)

PAGE 1
PART NO. 5844 FORD F150 WITHOUT FENDER FLARES FRONT MUD GUARD INSTALLATION INSTRUCTIONS Install Paint Protection Film before mud guards (see other side) Please read instructions thoroughly before installation. Tools Required • 1/8” drill bit / Drill • Short #2 Phillips screwdriver • Center punch • • • • • • Package Contents Driver & passenger side front mud guard #10 SEM screw (qty. 2) U-clip (qty.
PAGE 2
PART NO. 5844 4. Apply a flexible paint as directed by the paint manufacturer. PAINT PROTECTION FILM - INSTALLATION INSTRUCTIONS NOTE: The Paint Protection Film is a precut template of film used to protect the mud guard mounting surfaces of your fenders against wear. The templates (left and right side) can be removed from the backing liner by folding the liner at the center cut of the template, separating the film sides and peeling the film templates from the backing liner. 1.
PAGE 3
PART NO. 5944 FORD F150 WITHOUT FENDER FLARES REAR MUD GUARD INSTALLATION INSTRUCTIONS Install Paint Protection Film before mud guards (see other side) Please read instructions thoroughly before installation. Tools Required • 1/8” drill bit / Drill • Short #2 Phillips screwdriver • Center punch • • • • • • Package Contents Driver & passenger side rear mud guard #10 SEM screw (qty. 6) U-clip (qty. 4) Spring Clip (qty.
PAGE 4
PART NO. 5944 PAINT PROTECTION FILM - INSTALLATION INSTRUCTIONS NOTE: The Paint Protection Film is a precut template of film used to protect the mud guard mounting surfaces of your fenders against wear. The templates (left and right side) can be removed from the backing liner by folding the liner at the center cut of the template, separating the film sides and peeling the film templates from the backing liner. 1. Position mud guard on fender to indicate placement location of paint protection film. 2.