User's Manual

GettingStarted
BatteryInstallation(BatteriesnotIncluded)
Thecalleruses8AAbatteries(AlkalineorRechargeableNIMH).CAUTION:
Never attempt to recharge nonrechargeable batteries. Doing so could
damage the caller and could cause fire and/or personal injury. Remove
batterydoorbyunscrewingthethumbscrewatthetopofthebatterydoor.
Insertbatteriesintheproperorderasindicatedinthebatterycompartment.

Theremoteuses3AAbatteries(AlkalineorRechargeableNIMH).CAUTION:
Never attempt to recharge nonrechargeable batteries. Doing so could
damagethecallerandcouldcausefireand/orpersonalinjury.Removethe
rubberprotectivecoverfromtheremotethenremovebatterydoor.Insert
batteriesintheproperorderasindicatedinthebatterycompartment.

PowerOn
Topoweronboththecallerandremote,pressandholdthepowerbutton
for5seconds.
Thecallerwasdesignedtobeusedbyremotebutcanbeusedwithoutthe
remote.

SelectingaTracktoPlay
To use the caller without the remote simply use the track up and down
buttons on the caller to scroll to the desired track number and press the
selectbuttontoselect.Usevolumeupanddownbuttonstoselectdesired
volumelevel.

Using the remote controller. Use the track up and down buttons on the
callertoscrolltothedesiredtrackandpresstheselectbuttontoselect.Use
volumeupanddownbuttonstoselectdesiredvolumelevel.







1
MuteIndicator:LocatedonthebottommiddleportionoftheLCDscreenon
theremote.Thisindicates(whenlit)thatthecallerismuted.Whennotlit
thecallerisnotmuted.
Battery Level Indicator: Located at the bottom right portion of the LCD
screenontheremote.Thisindicatestheremotescurrentbatterylevel.

ÊSynchronizationofyourcallerandremotetracklist.
After any changes have been made to the track list or a firmware update
has been completed, you must resynchronize the caller and the remote.
Thisassuresthatthetracklistanddescriptionsarethesameontheremote
andthecaller.Todothisyousimplyperformthefollowingsteps.
1. Poweronthecaller
2. Powerontheremotecontrol
3. Press and hold the “Track Select” button on the remote for 15
seconds or until the remote displays “Synchronizing”. NOTE: The
remoteandcallermustbewithin10feetofeachotherduringthis
process.Resyncingtheremoteerasessaved“HotButton”settings.
Oncethesynchronizationprocesshascompletedyournewtracklist
will automatically be displayed on the remote. At this time your
callerisreadyforuse.

ÊConfiguring“HotButtons”onyourRemote
“Hot Buttons” store selected tracks and selected volume levels for easy
quick access to your most used tracks. This is a very handy feature that
keeps your most used sounds readily accessible. These “Hot Buttons” are
locatedjustbelowtheRemote’sLCDdisplayandarenumbered“1”“2”“3”
and“4”.Tosetthe“HotButtons”performthefollowingsteps.
1. Poweronthecaller
2. Powerontheremote
3. Selectyourdesiredtrack.
4. Selectyourpreferredlevelofvolume.
5. Pressandholdthe“HotButton”youwishtosaveyourtrackand
volumelevelstofor5seconds.Toconfirmthesettingsweresaved
lookatyour“HotButtons”Indicatoratthetoplefthandcornerof
yourremote’sLCDscreen.Asuccessfulsavewillbeindicatedby
highlightingthe“HotButton”numberthatyousetitto.
6. Repeatsteps35toseteach“HotButton”toyourdesiredtrackand
volumelevel.

10