Oscillating Stand Fan Owner’s Manual English Model 90405 90434 90435 Form# 44086-01 20101102 ©2010 Hunter Fan Co.
Table of Contents Introduction ������������������������������������������������������������� 3 Safety and Warnings ������������������������������������������������ 3 Grounding ��������������������������������������������������������������� 5 Fused Plug ��������������������������������������������������������������� 6 Unpacking ��������������������������������������������������������������� 7 Base Assembly ��������������������������������������������������������� 7 Motor Assembly ����������������������������
Introduction Thank you for choosing the Hunter Oscillating Stand Fan. This manual gives you complete instructions for assembling and using your fan. Here are some the features you will enjoy with your fan: 33An attractive design that enhances any decor 33A powerful motor for maximum air flow 33Three speeds to adjust your comfort level 33All metal construction Safety and Warnings To reduce the risk of fire or electrical shock, DO NOT use this fan with any solid-state speed control device.
through the grill when the fan is running. 10. DO NOT operate any appliance with a damaged cord or plug, after the appliance malfunctions or has been dropped or damaged in any manner. 11. To disconnect, grip plug and pull from wall outlet. NEVER yank on cord. 12. ALWAYS use on a dry surface. 13. This product is intended for household use only and not for commercial or industrial use. 14. DO NOT operate fan in the presence of explosive and/or flammable fumes. 15.
Grounding This appliance is for household use only and may be plugged into any 120-volt AC electrical outlet (ordinary household current). DO NOT use any other type of outlet. Grounded Plug Warning Grounding Pin Grounded Outlet Box Cover This unit is suitable for grounded receptacle use only. The power cord has a grounded plug as shown in Figure 1, and must be used with an electrical outlet that can accommodate the grounding pin.
Fused Plug This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. If the fuse fails, it is generally due to a short circuit or circuit overload.
Unpacking (2) Base Cover As you unpack the fan, save the carton and packing materials in case you want to move or ship the unit in the future. Carefully remove all items from the box. NOTE: It is best to have someone hold the box while you lift the fan and the protective packaging out of the carton. Make sure all shipping materials are removed from fan before operating. (1) Base Weight Figure 3. Base Assembly 1. Insert the Weight(1) into the Base Cover(2). Figure 3. 2.
Motor Assembly 1. Grasp the Telescope Pole firmly and twist the Adjustment Knob Counter Clockwise to loosen. Figure 7. 2. Raise the Inner Pole and tighten the Adjustment Knob by twisting Clockwise until secure. 3. Remove the Motor Knob(7), Motor Bolt(6), and Tilt Adjustment Knob(8). Loosen the screw above the Motor Knob(7). 4. Set the Motor(5) on top of the Pole(3), Figure 8., and Secure using the Motor Bolt(6) and Knob(7). Retighten the screw above the motor knob in the slot to secure motor. Figure 9.
Grill Assembly Handle 1. Place the back grill against the motor housing(5), Figure 11., and line up the 4 tabs on the back of the grill(9) to the 4 screws holes on the front of the motor. (9) Back Grill Caution: Make sure the Handle on the back of the Back Grill is facing up. 2. Attach the Back Grill(9) to the Motor(5) using the 4 Grill Mount Screws. Figure 12. (5) Motor Figure 11. Note:1 screw will have a star washer on it, for grounding purposes. The other 3 screws will not have a washer. 3.
Grill Assembly (Cont.) (9) Back Grill Hunter Logo 1. Remove the Grill Ring from the Front Grill(11) by loosening the screw holding it. 2. Place the Front Grill(11) against the Back Grill(9) so the Hunter logo faces right side up and push together until the tabs on the grills hold them together. Figure 15. 3. Slide the Grill Ring over both Front(11) and Back(9) Grills turning it so the screw that will secure it is on the bottom. Figure 16. (11)Front Grill Figure 15. 4.
Operation Off / Speed Selection To turn the fan on and off / control the speed. Turn the speed knob on the top of the motor to the porper setting. Figure 19. Low Off Medium High Oscillation To allow the fan to oscillate, push the Knob beside the fan speed control down. Pull up on the knob if oscillation is not desired. Figure 20. Figure 19. Adjustment To adjust the angle the fan is blowing. 1. Loosen the adjustment knob under the Fan Motor 2.
Maintenance This fan is permanently lubricated and will not require additional lubrication (oil) for the life of the fan. This fan requires little maintenance and contains no user serviceable parts. DO NOT try to fix it yourself. Contact qualified service personnel if servicing is needed. Before cleaning, turn fan off and unplug from electrical outlet. Wipe off excess dust with a lintfree cloth.
1. Problem 33Fan will not oscillate. Solution 33Push down on the knob on top of motor housing to activate oscillation. 2. Problem 33Can not adjust the angle of the fan. Solution 33Loosen the adjustment knob, tilt the fan, then retighten adjustment knob.
y IF THE USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN, THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT TO THE GLASS GLOBES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE FAN.
IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. y SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. nt ra ar W any such damage. Proof of purchase is required when requesting warranty service. The purchaser must present sales receipt or other document that establishes proof of purchase.
