8" Sherpa Cart Fan Owner’s Guide and Installation Manual English Español Page 21 Français Form #44805 20081023 ©2008 Hunter Fan Co.
Important Safety Information Read & Save These Instructions CAution near an open flame, cooking or any other heating appliances. When using electrical appliances, basic precautions should always be taken to reduce the risk of fire, electric shock and personal injury: 12. DO NOT use near curtains, plants, window treatments, etc. 13. Never operate the fan if the grills are not properly installed. Operating the fan without the grills could result in serious injury. 1.
Welcome Unpacking Thank you for choosing a Hunter As you unpack the fan, save the carton Fan. This manual gives you complete and packing materials in case you want to instructions for using your fan. move or ship the unit in the future. Carefully remove all items from the box. Before using your fan, record the following information for your records and for NOTE: It is best to have someone hold warranty assistance. the box while you lift the fan and the protective packaging out of the carton.
Grounding Instructions LINE CORD SAFETY TIPS This appliance is for household use only and may be plugged into any 120-volt 1. NEVER pull or yank on the cord or the appliance. AC electrical outlet (ordinary household current). DO NOT use any other type of 2. To insert plug, grasp it firmly and guide it into the outlet. outlet. Warning 3. To disconnect the appliance, grasp the plug and remove it from the outlet. This unit is suitable for grounded receptacle use only. 4.
Assembly [b] [a] [a] [b] [c] [b] 2. Place the Axle [a] between the Wheel Brackets [b]. [a] [a] 3. Fasten with Large Bolt [a], Lock Washer [b], and Flat Washer [c]. 4. Tighten with Large Allen Wrench [a] (included). [a] [a] [b] 5. Insert Grey Upright Tubes [a] into Base Assembly [b]. 44805 6. Make sure the Holes [a] in the tubes are facing inward. [5] 10/23/2008 ENGLISH 1. Insert Sleeve [a] into center of Wheel [b].
Assembly [a] ENGLISH [c] [a] [b] 7. Fasten Small Bolt [a] and Nylon Nut [b] using Small Allen Wrench [c] (included) and an adjustable wrench or pliers. 8. Store the Small Allen Wrench [a] in the cover of the electrical box when not in use. This wrench can be used to adjust the tilt resistance (see page 7). [a] [a] [a] [b] 9. Lower the Fan Assembly [a] onto the Tubes [b] of the base assembly. Slide down until it stops. 10.
Operation ADJUSTING HEIGHT OF FAN 1. 2. 3. 4. ENGLISH • This fan has a special height adjustment feature allowing it to be placed near a standard height window. Place you foot on the carrying ledge. Pull in on thumb levers. Raise fan assembly slightly and release levers so they will locate in the next hole. Slowly raise or lower the fan to the desired position. • The fan section can be raised and locked approx. 9" and 16" from the load carrying position.
Operation HALOGEN LIGHTS [b] 1. Each light has its own switch [a]. 2. Push once to turn the lamp on. Push again to turn the light off. 3. 150 watt Bulbs are included. • To replace bulbs.: i. Unplug unit and make sure lights cool down. ii. Remove the wing nut [b] at the top of the back of the light. [a] ENGLISH iii. Carefully let the cover hinge down so as not to break the lens. Warning iv. Re-lamp with Type T-3 150 watt bulb or smalller.
STORAGE 1. ALWAYS store the fan in a dry place. 2. NEVER store the fan while it is still plugged in. 3. NEVER wrap the cord tightly around the fan. 4. DO NOT put any stress on the cord where it enters the fan, as it could cause the cord to break. MAINTENANCE This fan is permanently lubricated and will not require additional lubrication (oil) for the life of the fan. This fan requires little maintenance and contains no user serviceable parts. DO NOT try to fix it yourself.
Form #44805 20081023 ©2008 Hunter Fan Co.
